Haas+Sohn HSP 6 Pallazza III 535.08-PGI Technical Document

HSP 6 Pallazza III 535.08–PGI
Equipment sheet
Pellet stove GB
0553508021413a
Equipment sheet
HSP 6 Pallazza III 535.08–PGI

GB
Notes in the text
Of utmost importance there are the notes entitled WARNING. The notes entitled WARNING advise you on
serious danger of damage to the heating device or of an injury.
The note entitled Notice advises you on possible damage to your heating device.
The note entitled Important calls your attention to the information important for the operation of your heating
device.
The note itself calls your attention to the information important for the operation of your heating device in
general.

Contents
GB
Contents
1. Technical data.............................................................................................................................. 1
2. Dimensions................................................................................................................................... 2
3. Cleaning work .............................................................................................................................. 3
3.1. Cleaning the surface ................................................................................................................. 3
3.2. Cleaning the glass panel .......................................................................................................... 3
3.3. Clean combustion chamber “function instruction” Error F040............................................. 3
3.4. Cleaning the combustion pot - weekly .................................................................................... 3
4. Maintenance work....................................................................................................................... 5
4.1. Cleaning the flue gas passes ................................................................................................... 5
4.2. Cleaning the pellet container - annual maintenance ............................................................ 8
5. Replacement parts list............................................................................................................... 9
5.1. Replacement parts list Pallazza III 535.08–PGI (without trim parts).................................. 9
5.2. Detail A1.................................................................................................................................... 11
5.3. Replacement parts list Pallazza III 535.08–PGI.................................................................. 12
6. Circuit diagram .......................................................................................................................... 13

Technical data
GB
1
1. Technical data
Pallazza III 535.08 –
PGI
Heat output range: 2,4 – 8,3 kW
Nominal heat output: 8,0 kW
Height: 1195 mm
Width: 557 mm
Depth: 493 mm
Weight: 138 kg
Diameter of flue elbow: 80 mm
Flue gas temperature: 206 °C
Testing transport pressure at nominal output: 11 Pa
Testing transport pressure at partial output: 5 Pa
Flue gas flow rate in g/s 5,6 g/s
CO level in flue gas (%) (min./max.) 0,001/0,023 %
Efficiency: 90/95%
CO level in flue gas: 15 mg/Nm³
NOx level in flue gas: 143/- mg/Nm³
OGC level in flue gas: <5 mg/Nm³
Proportion of dust in flue gas: 9/- mg/Nm³
Contents of storage container (pellet tank): about 32 kg
Duration of burn with one charge (min./max.): about 20 h/60 h
Permitted fuel: Low-dust wood pellets Diameter: 6 mm
to Ö-Norm M 7135, DIN plus, EN plus-A1 Length: max. 30 mm
Room heating capacity to Ö-Norm M 7521: max. 230 m³
Room heating capacity to DIN 18893, constant heating: 250m³/145m³/98m³
Room heating capacity to DIN 18893, timed heating: 165m³/95m³/65m³
Electricity supply: 230 V (50 Hz)
Electricity supply input:
in normal operation: max. 50 W
Electric ignition (for max. 15 minutes on ignition): max. 380 W
Electronics fuses: (F3) T 0,315 A, 250 V
Fuses for the ignition, screw conveyor motor, induced draught,
(F1) T 3,12 A, 250 V
Safety distances
Minimal distances from flammable materials:
side: 15 cm
rear: 10 cm
front (radiation area): 80 cm

Dimensions
GB
2
2. Dimensions

Cleaning work
GB
3
3. Cleaning work
WARNING
Before starting any cleaning work, the stove must be cool down!
Once the cleaning work is completed, the correct operating status of the device must be re-
established: Put the combustion pot in correctly, close the combustion chamber door.
3.1. Cleaning the surface
Dirt on the upper surface of the stove may be cleaned off with a damp cloth or if necessary with mild soapy
water. You are advised against using corrosive cleaning agents and solvents since these might damage the
surfaces.
3.2. Cleaning the glass panel
To clean the viewing panel, you must first open the stove door. Dirt on the glass panel can be removed with a
glass cleaner or with a damp sponge on which you have sprinkled some of the wood ash present.
(Environmentally friendly). Cleaning the glass panel may only be done with a cooled down stove in the OFF
operating mode.
3.3. Clean combustion chamber “function instruction” Error
F040
• The whole combustion space must be cleaned after 30-hours operation at the latest, or once a week.
• The requirement to clean the fire-box (flickering of the display) appears during heating, in case that the
cleaning interval has elapsed.
• After the fire-box has been cleaned, the error message "Clean the fire-box" will be confirmed automatically.
The condition for automatic confirmation of this error message is that the fire-box door is opened for more
than 60 seconds. This time is necessary for careful cleaning of the fore-box, including the burner.
• This reset of the operating hours counter occurs even if the cleaning of the combustion chamber is
performed before the 30 operating hours have run provided that the stove is in “Off” operating status and the
door is open for longer than 60 seconds during cleaning.
3.4. Cleaning the combustion pot - weekly
During operation, deposits may form in the combustion pot. How quickly the combustion pot becomes dirty
depends solely on fuel quality. The deposits or encrustations must be removed from time to time.

Cleaning work
GB
4
WARNING
If this is not done, the clinker will continue to accumulate. Then the device will no longer be able to ignite
properly. Pellets can pile up in the combustion pot. In extreme cases, this can reach all the way back to the
pellet chute. Backfire in the pellet container and smouldering in the pellet tank might possibly result.
This will destroy your device and is not covered in your guarantee.
WARNING
Cleaning the combustion pot may only be done with a cooled down stove in “OFF” operating mode.
Otherwise there is a risk of burns!
• Take out the burner bowl from the stove.
• Remove the remains of ashes and slag.
• After the cleaning, mount the burner bowl back to its proper position on the burner rest.
• Re-check the proper seating of the burner bowl, in order to avoid any lack of tightness.

Maintenance work
GB
5
4. Maintenance work
WARNING
Before starting any cleaning work, the stove must be cool down! The mains plug must be pulled out of
the power supply socket (always in advance)!
The frequency of maintenance in turn depends to a large extent on the pellet quality (ash content). Quality
pellets have a low ash content of about 0.2-0.3%. However, if the ash content is higher (0.5% and over), the
interval from maintenance to maintenance is reduced and the accumulation of ash increases by 2 or 3 times.
WARNING
Devices that are not maintained in accordance with our specifications must not be operated. Failure to
observe this point will invalidate all guarantee claims.
4.1. Cleaning the flue gas passes
CAUTION
Check and clean the flue-gas ways, exhaust (flue-gas) fan and flue-gas ducts at the latest after 1000 kg of
pellets have been consumed. Clean with a brush or an ash extractor.
Please perform the cleaning in two steps:

Maintenance work
GB
6
Figure 1: Removing the flue baffle