Habitat Border BORD-AV-SS15-A User manual

Depth - 43cm
Width - 110cm
Height - 42cm
Tools required
Border AV Unit
Dimensions
If you need help or have damaged or missing parts, email:
[e-mail] or call: 0344 499 4686
Dimensions
Assembly Instructions — Please keep for future reference
Important — Please read these instructions before assembly
BORD-AV-SS15-A

General care and maintenance
General information
Maximum weight limit
Important:
max load for shelf is shown below.
Safety and Care Advice
Assemble on a soft level surface
to avoid damaging the unit or your
floor.
We do not
recommend the
use of power drill/
drivers for inserting
screws, as this could
damage the unit. Only use hand
screwdrivers.
Dispose of all packaging carefully
and responsibly.
Do not stand or put weight on the
product, this could cause damage.
Assemble the item as close to its
final position (in the same room)
as possible.
Do not place furniture directly in
front of radiators, fires or any
other source of heat.
Parts of the
assembly will be
easier with 2
people.
Check you have all the
components and tools listed on
the front cover and pages 2 - 3.
Remove all fittings from the
plastic bags and separate them
into their groups.
Keep children and animals away
from the work area, small parts
could choke if swallowed.
Make sure you have enough
space to layout the parts before
starting.
Received, please contact the store
or Habitat Head Office via its web
site: www.habitat.co.uk
or write directly to:
Habitat Retail Ltd.
489-499 Avebury Boulevard,
Milton Keynes MK9 2NW
Please retain your receipt as
proof of purchase.
If you have any comment or
suggestions regarding this
product, assembly instructions
or service.
If for any reason you should have
problems with your Habitat
product, please contact the store
from which you purchased it.
1
Dust regularly with a clean dry
cloth.
Wipe up any spills immediately
with a damp cloth and then dry
the surface with a clean dry
duster.
Repeat this procedure for
periodic cleaning.
From time to time check that
there are no loose screws on
this unit.
This product should not be
discarded with household waste.
Take to your local authority waste
disposal centre.
The use of furniture polish or
spray is not necessary or
recommended.
Always use place mats and
coasters to protect the surface
from moisture and heat.
Important — Please read these instructions fully before starting assembly

BC
BC
Components - Panels If you need help or have damaged or missing parts, email:
[e-mail] or call: 0344 499 4686
Note: There are 'Batch Code' lables where shown on the indicated items, these should be retained.
2
3. Right side
10. Adjustable foot
2. Left side
4. Bottom
6. Adjustable shelf x 2
8. Back panel 9. Foot x 2
11. Door x 2
7. Back lower rail
5. Wall
1. Top
Please check you have all the panels listed below

5 55 60 65 70 75 80 85 90 95 100 105 110 115 1205045403530252015100
Fittings contained
in Pack 1
Ø3.5x16mm Screws x 4
B
Magnetic catchs x 2
C
Ø8x30mm Wooden dowels x 18 Ø6x41mm Metal dowels x 28
Ø4x14mm Screws x 26
Ø26mm Hinges x 4
Ø26mm Hinge plates x 4
Magnetic catch plates x 2Shelf supports x 4Ø15x15mm Locking cams x 28
P
Ø3x12mm Screws x 4
A
DFE
GHK
M
If you need help or have damaged or missing parts, email:
[e-mail] or call: 0344 499 4686Components - Fittings
Note: The quantities below are the correct amount to complete the assembly.
In some cases more fittings may be supplied than are required.
3
Please check you have all the fixin
g
s listed below
Ruler — To help correctly id entify the fixings

B
1E
FF
4
Assembly Instructions
4
B
B x 9 E x 2 F x 4
B x 19
4
Step 2
Step 1