Habitat Quattro 814/3859 User manual

Quattro Chair
Assembly Instructions - Please keep for future reference 814/3859
760/7286
Important - Please read these instructions fully before starting assembly
If you need help or have damaged or missing parts, call the Customer Helpline:
Argos= 0345 640 0800
Issue 1 -05/09/20
Dimensions
Width - 52cm
Depth - 49cm
Height - 71cm

1
• Check you have all the
components and tools listed on
the following pages.
• Remove all fittings from the
plastic bags and separate them
into their groups.
• Keep children and animals
away from the work area, small
parts could choke if swallowed.
• Make sure you have enough
space to layout the parts before
starting.
• During assembly do not stand
or put weight on the product, this
could cause damage.
• Assemble the item as close to
its final position (in the same
room) as possible.
• Assemble on a soft level
surface to avoid damaging the
unit or your floor.
• Parts of the assembly will be
easier with 2 people.
• We do not
recommend the
use of power
drill/drivers for
inserting screws,
as this could damage the unit.
Only use hand screwdrivers.
• Unit weight: 4.2 kgs.
• Maximum safe weight of user:
110kgs.
Safety and Care Advice
Important - Please read these instructions fully before starting assembly
Care and maintenance
Handy Hints
• Only clean using a damp cloth
and mild detergent, do no use
bleach or abrasive cleaners.
• From time to time check that
there are no loose screws on
this unit.
• Always lift the product when
moving it around. Never drag.
• Do not stand on the product.
• Do not use this product as step
ladder.
• This product should not be
discarded with household
waste. Take to your local
authority waste disposal centre.
• Assemble all parts and bolts
loosely during assembly, only
once the product is complete
should you fully tighten the
bolts.
• Regularly check and ensure
that all bolts and fittings are
tightend properly.

2
Components - Parts
Please check you have all the parts listed below
If you have damaged or missing components,
call the Customer Helpline: 0345 640 0800
Components - Fittings
Please check you have all the fittings listed below
Note: The quantities below are the correct amount to complete the assembly. In some cases more fittings
may be supplied than are required.
Ruler - Use this ruler to help correctly identify the screws
0 15 30 45 60 75 905 20 35 50 65 80 9510 25 40 55 70 85 100 120 140105 125 145110 130 150115 135 155 160 165 170
D
Washer x 5
Spring washer x 5
C
Upper Leg2Seat1Lower Leg3
M6 x 50mm Bolt
A
M6 x 65mm Bolt x 4
B
E
Allen key x 1
F
Foot pad x 4

Assembling the seat
Place the seat face
down on a flat protected
surface.
Position the legs &
on the seat then align
and fix through holes
using bolts , spring
washers and flat
washers . Tighten the
bolts using allen key .
Carefully turn the chair
upright and place on a
flat surface.
3
Assembly Instructions
Step 1
Assembling legs
Attach the upper leg
to the lower leg as
shown and fix through
holes using bolt ,
spring washer and flat
washer . Tighten the
bolt using allen key .
3
2
Step 2
3
2
C
A
D
3
2
3
2
A
A
A
C
C
D
D
E
E
E
C
D
3
3
2
2
3
2
1
3
2
1
1
3
2B
E
C
D
B
C
D
B
C
D
B
C
D
B
C
D
B
C
D
1
2 3

4
Assembly Instructions
Step 3
Assembly is complete.
If you need help or have damaged or missing parts, call the Customer Helpline:
Argos= 0345 640 0800
3
2
Attaching foot pads
Remove backing from
foot pads and carefully
position on the bottom of
sa&sgeleht
shown.
23
F
FF
F
F
Carefully turn the chair
upright after assembly.