Haier HPU-18H03 User manual

PACKAGED UNIT
OPERATION MANUAL
Please read this operation manual before using the air conditioner.
0010519818
HPU-18C03/E1
HPU-24C03/E1
HPU-18H03/E1
HPU-24H03/E1

Cautions
Disposal of the old air conditioner
Before disposing an old air conditioner that
goes out of use,please make sure it's
inoperative and safe. Unplug the air
conditioner in order to avoid the riskof child
entrapment.
It must be noticed that air conditioner
system contains refrigerants,which require
specialized waste disposal. The valuable
materials contained in an air conditioner can
be recycled. Contact your local waste
disposal center for proper disposal of an
old air conditioner and contact your local
authorityor your dealer if you haveany
question. Please ensure that the pipework
of your air conditioner does not get damaged
prior to being picked up bythe relevant
waste disposal center,and contribute to
environmental awareness byinsisting on
an appropriate,anti-pollution method of
disposal.
Disposal of the packaging of your
new air conditioner
All the packaging materials employed in the
package of your newair conditioner may
be
disposed without anydanger to the
environment.
The cardboard boxmaybe broken or cut into
smaller pieces and given to a waste paper
disposal service. The wrapping bag made of
polyethylene and the polyethylene foam pads
All these valuable materials maybe taken
to awaste collecting center and used again
after adequate recycling.
Consult your local authorities for the name
and address of the waste materials
collecting centers and waste paper disposal
services nearest to your house.
Safety Instructions and Warnings
Before starting the air conditioner,read the
information given in the User'sGuide
carefully.The User'sGuide contains very
important observations relating to the
assembly, operation and maintenance of
the air conditioner.
The manufacturer does not accept
responsibilityfor anydamages that may
arise due to non-observation of the following
instruction.
Damaged air conditioners are not to be
put into operation. In case of doubt,consult
your supplier.
Use of the air conditioner is to be carried
out in strict compliance with the relative
instructions set forth in the User'sGuide.
Installation shall be done byprofessional
people,don't install unit byyourself.
For the purpose of the safety,the air conditioner
must be properlygrounded in accordance
with specifications.
Always remember to unplug the air
conditioner before openning inlet grill. Never
unplug your air conditioner bypulling on
the power cord. Always grip plug firmlyand
pull straight out from the outlet.
All electrical repairs must be carried out
byqualified electricians. Inadequate repairs
mayresult in amajor source of danger for
the user of the air conditioner.
Do not damage anyparts of the air
conditioner that carryrefrigerant bypiercing
or performating the air conditioner's tubes
with sharp or pointed items ,crushing or
twisting anytubes ,or scraping the coatings
off the surfaces. If the refrigerant spurts
out and gets into eyes ,it mayresult in
serious eyeinjuries.
1

Cautions
Do not obstruct or cover the ventilation
grille of the air conditioner. Donotput
fingers or anyother things into the
inlet/outlet and swing louver.
Do not allowchildren to playwith the air
conditioner. In no case should children be
allowed to sit on the outdoor unit.
Specifications
The refrigerating circuit is leak-proof.
1. Applicable ambient temperature range:
2. If the power supplycord is damaged,it
must be replaced bythe manufacturer
or its service agent or a similar qualified
person.
3. If the fuse on PCboard is broken,please
change it with the type of T. 3.15A/ 250V.
4. The wiring method should be in line with
the local wiring standard.
5. After installation,the power plug should
be easilyreached.
6. The waste batteryshould be disposed
properly.
7. The appliance is not intended for use by
young children or infirm persons without
supervision.
8. Young children should be supervised to
ensure that theydo not playwith the
applience.
9. Abreaker should be used in the circuits,
which should be all-pole cutoff and the
distance between its two contacts should
be not at least 3mm .
10.Please employthe proper power plug,
which fit into the power supplycord.
11.The power plug must haveacquired the
local attestation.
The machine is adaptive in following
situation
Cooling
Indoor
Outdoor
Maximum: D.B/W.B32°C/ 23°C
Minimum: D.B/W.B18°C/ 14°C
Maximum: D.B/W.B43°C/ 26°C
Minimum: D.B18°C
Maximum:D.B27°C
Minimum:
Minimum:
D.B15°C
Maximum: D.B/W.B24°C/ 18°C
D.B/W.B-7°C/-8°C
2
Indoor
Outdoor
Heating

Cautions
Please read the following SafetyInstructions carefullyprior to use.
The instructions are classified into twolevels,WARNING and CAUTIONaccording to the
seriousness of possible risks and damages as follows. Compliance to the instructions are
strictlyrequired for safetyuse.
Safety Instruction
Installation
WARNING
Please call Sales/Service Shop for the Installation.
Do not attempt to install the air conditioner byyourself because improper worksmay
cause electric shock, fire,water leakage.
CAUTION
Installation in an inadequate place maycause accidents. Do not install in the following place.
Connect the earth
cable.
PROHIBITIONPROHIBITION
STRICT
ENFORCEMENT
Do not install in the
place where there
is anypossibility
of inflammable
gas leakage around
the unit.
Do not get the unit
exposed to vapor
or oil steam.
Checkproper
installation of the
drainage securely
Use fuse with specified capacity.
Replacement with steel or copper wires are
absolutelyprohibited.
Grounding wire should not be connected to
that of gas pipeline,water pipeline,lighting
arrester or telephone.
FUSE
STEEL WIRE
COPPERWIRE
3

When abnormalitysuch as burnt-small found,immediately
stop the operation button and contact sales shop.
Connect power supplycord to the
outlet completely.
After installed,the unit shall be
tested for electric leakage.
Takecare not to damage the
power supplycord.
Do not use power supplycord in
a bundle.
Donotusepower supplycord
extended or connected in halfway.
Do not insert objects into the air
inlet or outlet.
Do not tryto repair or reconstruct
byyourself.
PROHIBITION
PROHIBITION
PROHIBITION
PROHIBITION
PROHIBITION
OFF STRICT
ENFORCEMENT
STRICT
ENFORCEMENT
Use an exclusivepower source with a circuit breaker.
CAUTION
Do not use for the purpose of
storage of food,art work, precise
equipment,breeding ,or cultivation.
Take fresh air occasionally
especiallywhen gas appliance is
running at the same time.
Do not operate the switch with wet
hand.
Do not pour water onto the unit
for cleaning.
Checkgood condition of the
installation stand.
Do not install the unit near a fireplace
or other heating apparatus.
Do not place animals or plants in
the direct path of the air flow.
Do not place anyobjects on or
climb on the unit.
Do not place flower vase or water
containers on the top of the unit.
PROHIBITION
PROHIBITION
PROHIBITIONPROHIBITION
PROHIBITION
PROHIBITIONPROHIBITION
PROHIBITION
STRICT
ENFORCEMENT
Cautions
WARNING
Use of Air Conditioner
Do not channel the air flowdirectly
at people,especiallyat infants or
the aged.
Do not start or stop the operation
bydisconnecting the power supply
cord and so on.
PROHIBITION
4

Parts and Functions
Outdoor unit
Indoor unit
1.OUTLET
2.CONTROLPANEL
4.INLET
3.INLET GRILLE
2.INLET 4.DRAIN HOSE
1.OUTLET 3.CONNECTING PIPING AND ELECTRICAL WIRING


5
HPU-18C03/E1
HPU-18H03/E1
HPU-24C03/E1
HPU-24H03/E1

Operation mode AUTOFANCOOLDRY
Remote controller
Displayboard
18.Singal sending display
When the remote controller appears abnormal,
use a sharp pointed article to press this button
to reset the remote controller normal.
1. RESET
Used to select TIMER ON, TIMER OFF,
TIMER ON-OFF.
3. TIMER button
Used to set correct time.
4. CLOCK button Used to select sleep mode.
25. .SLEEP button
6. MODE button
Used to set clockand timer setting.
7. HOUR button
Used to set healthyoperation.
5. HEALTH button
Used for unit start and stop.
9. ON/OFF button
10. TIMER ONdisplay
11. FAN SPEED display
12. LOCK display
13. SWING UP/DOWNdisplay
14. SLEEP display
15. HEALTH display
16. E.HEATdisplay
Used to select your desired temperature.
17. Operation mode display
19. Left/right air flowdisplay
Remote controller: to displaythe TEMP. setting.
20. TEMP display
21. TIMER OFF display
23. TEMP button
Used to select fan speed: LOW,MED, HI, AUTO.
24. FAN button
8. SWING UP/DOWNbutton
Used to select up or down air sending direction.
Used to confirm timer and clocksettings.
26. SET button
Used to lockbuttons and LED display. If pressed,the
other buttons will be disabled and the lockcondition
displayappears. Press it once again,lockwill be
canceled and lockcondition displaydisappears.
28. LOCK
22. TIMER display
Remote controller
LOW HI
MED AUTO
19
2. LIGHTbutton
Control the lightening and extinguishing of
the indoor LED displayboard.
6
20 15 17
28
14
E.HEAT
HEAT
AUTOCOOLDRYFAN
HEAT
28
Used to operate electricityheat function.
27. E.HEAT button
BA
Control panel: See p17
NOTE:(1) The following functions and related displays are not available:
(2) Cooling onlyunit do not have functions and displays related with heating.
5
(3)The air conditioner you bought,maynot include the E.Heat function,is subject to the actual product.
Parts and Functions

17.Singal sending display
When the remote controller appears abnormal,
use a sharp pointed article to press this button
to reset the remote controller normal.
1. RESET
Used to select TIMER ON, TIMER OFF,
TIMER ON-OFF.
3. TIMER button
Used to set correct time.
4. CLOCK button
Used to select sleep mode.
24. .SLEEP button
6. MODE button
Used to set clockand timer setting.
7. HOUR button
Used to set healthyoperation.
5. HEALTH button
Used for unit start and stop.
9. ON/OFF button
10. TIMER ONdisplay
11. FAN SPEED display
12. LOCK display
13. SWING UP/DOWNdisplay
14. SLEEP display
15. HEALTH display
Used to select your desired temperature.
16. Operation mode display
18. Left/right air flowdisplay
Remote controller: to displaythe TEMP. setting.
19. TEMP display
20. TIMER OFF display
22. TEMP button
Used to select fan speed: LOW,MED, HI, AUTO.
23. FAN button
8. SWING UP/DOWNbutton
Used to select up or down air sending direction.
Used to confirm timer and clocksettings.
25. SET button
Used to lockbuttons and LED display. If pressed,the
other buttons will be disabled and the lockcondition
displayappears. Press it once again,lockwill be
canceled and lockcondition displaydisappears.
26. LOCK
21. TIMER display
Remote controller
Control panel: See p17
LOW HI
MED AUTO
19
2. LIGHTbutton
Control the lightening and extinguishing of
the indoor LED displayboard.
7
19 15 16
26
14
Operation mode AUTOFANCOOLDRY
Remote controller
Displayboard
AUTOCOOLDRYFAN
BA
NOTE:(1) The following functions and related displays are not available:
(2) Cooling onlyunit do not have functions and displays related with heating.
5
Parts and Functions

Remove the batteries in case unit won't be in usage for a long period. If there are any display
after taking-out, just need to press reset key.
Clock Set
When unit is started for the first time and after replacing batteries in
remote controller, clock should be adjusted as follows:
Remote controller's operation
3. After time setting is confirmed, press SET, "AM" or "PM" stop flashing,
while clock starts working.
2. Press or to set correct time. Each press will increase or decrease
1 min. If the button is kept depressed, time will change quickly.
1. Press CLOCK button,"AM" or "PM" flashes.
When in use, put the signal transmission head directly to the receiver hole on the indoor unit.
The distance between the signal transmission head and the receiver hole should be within
7m without any obstacle as well.
Don't throw or knock the remoter controller.
When electronic-started type fluorescent lamp or change-over type fluorescent lamp or
wireless telephone is installed in the room, the receiver is apt to be disturbed in receiving
the signals, so the distance to the indoor unit should be shorter.
Loading of the battery
Load the batteries as illustrated right
2 R-03 (7#) batteries
Remove the battery cover:
Slightly press" "area and push down the cover
as illustrated.
Load the battery:
Be sure that the loading is in line with the "+" / "-".
request as illustrated on the bottom of the case.
Put on the cover again.
Confirmation indicator:
After pressing power ON/OFF, if no display, reload the batteries.
Note:
Full display or unclear display during operation indicates the batteries have been used up.
Please change batteries.
Used two new same-typed batteries when loading.
If the remote controller can't run normally during operation, please remove the batteries and
reload several minutes later.
Hint:
8
E.HEAT
Parts and Functions

Control panel
Remote Controller
Operation
1. Unit start
Press ON/OFF on the indoor unit,or press ON/OFF on the
remote controller,unit starts.
The liquid crystal will displaythe working state of last
time (Expcept Timer and Sleep ).
2.
3.
Select operation mode
Press MODE button. For each press,operation mode
changes as follows:
Remote controller:
Control panel:
Then Select AUTO operation
4. Unit stop
ON/OFF button,the unit stops.Press
About AUTO mode
In this mode,the air conditioner will automaticallyselect
cooling ǃheating or fan operation mode according to room
temperature.
AUTO Operation
9
1
E.HEAT
AUTO COOL DRY FAN
HEAT
AUTO COOL DRY FAN
HEAT
Control panel: See p17
4