Haier HSU-12C03/K - annexe 1 User manual

Please read this operation manual before using the air conditioner.
Keep this operation manual for future reference.
SPLIT TYPE ROOM AIR CONDITIONER
OPERATION MANUAL
0010531056
HSU-12H03/K(F)
HSU-09H03/K(F)
HSU-12C03/K(F)
Contents
1
2-5
7
6.7
CAUTIONS
PARTS AND FUNCTIONS
OPERATION
TROUBLE SHOOTING

Used to select CODE A or B with a press,
A or B will be displayed on LCD.
Please select A without special explanation.
When the remote controller
pointed article to press this button
to reset the remote controller normal.
Control the lightening and
extinguishing of the indoor
LED display board.






Inlet grille

Inlet

Air Purifying Filter (inside)

Outlet

Horizontal flap





Parts and Functions
Actual inlet grille may vary from the one shown in the
manual according to the product purchased
(adjust up and down air flow
Don't adjust it manually)
(adjust left and right air flow)
Vertical blade
Remote controller
1
Outdoor Unit

Indoor Unit
OUTLET
INLET
CONNECTING PIPING AND ELECTRICAL WIRING
DRAIN HOSE
(inside)
Anion generator

Air Filter cleaning
Open the inlet grille by pulling it upward.
Remove the filter.
Clean the filter.
Attach the filter.
Close the inlet grille.
Push up the filter's center tab slightly until it is released
from the stopper, and remove the filter downward.
Use a vacuum cleaner to remove dust, or wash the filter with
water.After washing, dry the filter completely in the shade.
Attach the filter correctly so that the "FRONT" indication is
facing to the front.Make sure that the filter is completely
fixed behind the stopper.If the right and left filters are not
attached correctly, that may cause defects.
Once every
two weeks
FAN
COOL
SMART
HEAT
DRY
CTD
SET TEMP. ROOM TEMP.
AUTO AUTO
AUTO
FAN
SPEED
POWER
SOFT
iFP
ECO
TIMER ON OFF
PM
AM
COOL
SMART ON/OFF
HEAT
DRY
iFP
ECONOMY FAN SPEED
FOLLOW
EVADE



 Signal receiver hole

COOL display

HEAT display

HEALTH display
Dry display







(If the unit which you purchased
has healthy function,follow it.
TIMER OFF display
TIMER ON display
SLEEP display
If not,please ignore.)
Ambient temp.display
When receiving the remote control signal,
display the set temperature and in the rest
this room temperature is only for reference.
time the room temperature is displayed and
SMART display

Display board

iFP display


SMART
FAN
COOL
SMART
HEAT
DRY
CTD
SET TEMP. ROOM TEMP.
AUTO AUTO
AUTO
FAN
SPEED
POWER
SOFT
iFP
ECO
TIMER ON OFF
PM
AM
Signal sending end
Signal sending display
TEMP display
Remote controller: to display
the TEMP. setting.
FAN SPEED display
SWING UP/DOWN display
Left/right air flow display
TIMER ON display
TIMER OFF display
CLOCK display
Operation mode display
Display of each function status
SMART button
Used to set SMART operation.
ON/OFF button
Used for unit start and stop.
TEMP. button
Used to select your desired
temperature.
FAN SPEED button
Used to select fan speed:
LOW,MED, HI, AUTO.
FOOLLOW / EVADE button
Detect the location where the
human body is, adjust the air
deflector to blow/avoid the
body.
COOL button
Used to set COOL operation.
HEAT button
Used to set HEAT operation.
(Cooling only unit do not have
displays and functions related
with heating.)
DRY button
Used to set DRY operation.
ECONOMY button
Used to set ECONOMY operation.
iFP button
Induce the movement of the human
body, so as to control the
airflow/energy saving functioning.
SWING button
Used to select up or down air
sending direction.
HEALTH button
Used to set healthy operation.
HEALTH AIRFLOW button
Used to set the health airflow mode.
POWER / SOFT button
Use to set power/soft function.
SWING button
Used to select left or right air
sending direction.
FRESH button
Used to set fresh operation.
SLEEP button
Used to select sleep mode.
CLOCK button
Used to set correct time.
TIMER ON / OFF button
Used to select TIMER ON,
TIMER OFF,TIMER ON-OFF.
HOUR button
Used to set clock and timer
setting.
CANCEL/CONFIRM button
Used to confirm timer and
clock settings.
LOCK button
Used to lock buttons and LCD
buttons will be disabled and the
Press it once again, lock will be
cancelled and lock condition
display. If pressed, the other
lock condition
display appears.
display disappears.
CODE button
LIGHT button
INQUIRE button
Inquire the external environmental
temperature and the operating
power of the machine. (e.g. when
the panel display “01”, the operating
power is 100W; when the panel
display “02”, the operating power
is 200W, and so forth).
RESET button
appears abnormal,use a sharp
This function unavailable
on this models
NOTE:









Outer side of the controller
Inner side of the controller
(This function is unavailable on
some models.)

2
Operation
SMATR Operation
1
2
3

Remove the battery cover;
Load the batteries as illustrated. 2 R-03
batteries,resetting key(cylinder); Be sure
that the loading is in line with the" + "/"-";
Load the battery,then put on the cover
again.
Loading of the battery
The distance between the signal transmission head and the
receiver hole should be within 7m without any obstacle as well.
When electronic-started type fluorescent lamp or change-over
so the distance to the indoor unit should be shorter.
wireless telephone is installed in the type fluorescent lamp or
room, the receiver is apt to be disturbed in receivingthe signals,
Note:
Full display or unclear display during operation indicates the
ries have been used up.Please change batteries.
If the remote controller can't run normally during operation,
reload several minutes later.
batte
remove the batteries and
Remove the batteries in case unit won't be in usage for a long period.
If there are any display after taking-out, just need to press reset key
Hint:
please
Clock set
Press CLOCK button,
"AM" or "PM" flashes.
SMART
1
2
Each press will increase or
decrease 1min. If the
button
is kept pressed,time will change
quickly.
Press “+” or “-” to set correct time.
3Confirm
time.
After time setting is confirmed,
press CONFIRM,"AM "and
"PM" stop flashing,while
clock starts working.
SMART
ƽ SMART FRESH
ƽ SMART Defrost
ƽ
SMART FAN SPEED
ƽ
SMART FAN HEALTH
ƽ SMART SOFT
Under the cooling, heating and dehumidifying mode, press the
smart key to enter the smart function.
When the smart function is running, press the “cooling” “heating” or
“dehumidifying” key to switch to the other mode, you will exit from
the smart function.
Under the smart running mode, when the air conditioning is running,
it will automatically select cooling, heating, dehumidifying or blowing
mode as per the setting temperature.
One key can give you a comfortable room!
The air conditioning unit can judge the indoor
temperature and humidity, and make the
adjustment accordingly.
SMART SMART start
Press ON/OFF button, unit starts.
Press SMART button“ ” is displayed on
the remote controller and “ ” is displayed on
the display board,unit will run in SMART mode.
ƽ SMART DRY
ƽ SMART Control temperature
SMART SMART stops
or
COOL,HEAT and DRY Operation
SMART
Unit start.
1
Select operation mode.
2
Press COOL button“ ” is displayed on
the remote controller and “ ” is displayed on
the display board,unit will run in COOL mode.
Press HEAT button“ ” is displayed on
the remote controller and “ ” is displayed on
the display board,unit will run in HEAT mode.
Press DRY button“ ” is displayed on
the remote controller and “ ” is displayed on
the display board,unit will run in DRY mode.
1.In DR Y mode, when room temperature becomes lower than temp.setting+2
o
C,
unit will run intermittently at LOW speed regardless of FAN setting.
2.
just press ON/OFF button and unit will run in previous status.
Remote controller can memorize each operation status. When starting it next time,
3.
Cooling only unit do not have displays and functions related with heating.
PM
AM
SMART
AM
SMART
AM
(This function is unavailable on some models.)

Operation
Operation
SMART
Press TEMP button.
Every time the button is pressed,
temp. setting increases 0.5
oC.
Every time the button is pressed,
temp. setting decreases 0.5
oC.
Unit will start running to reach the temp.
setting on LCD.
1
2
Press FAN SPEED button. For each
press, fan speed changes as follows:
Unit will run at selected fan speed.
LOW HI
MED AUTO
Operation
SMART
1
2
For each press of “ ”button, air
flow direction on remote controller displays
as follows according to different operation modes:
COOL/DRY:
SMART:
HEAT:
For each press of “ ”button,
remote controller displays as follows :
remote controller:
Initial state
Initial state
As cold air flows downward in COOL mode, adjusting air flow horizontally will be
much more helpful for a better air circulation.
When humidity is high,condensate water might occur at air outlet if all
vertical louvers are adjusted to left or right.
It is advisable not to keep horizontal flap at downward position for a long
time in COOLor DRY mode ,otherwise, condensate water might occur.
HEALTH Operation
SMART
The anion generator in the airconditioner can
generate a lot of anion effectively balance the
to kill bacteria and speed up the dust sediment
in the room and finally clean the air in the room.
quantity of position and anion in the air and also
starts health anion function operation.
For twice press,
When the fan in the indoor unit does not work,
the health lamp lights up,but the anion generator
does not release anion.
When indoor fan motor is running, it has healthy
process function. (It's available under any mode)
For each press, is displayed
Air conditioner
Press HEALTH button
Press HEALTH button
disappears,the operation stops.
HEALTH AIRFLOW Operation
SMART
ON/OFF button and unit will run in previous status.
Remote controller can memorize each operation
status. When starting it next time,just press
The setting of health airflow function
1).Press the button of health airflow, appears
on the display. Avoid the strong airflow blows
2).Press the button of health airflow again,
appears on the display. Avoid the strong
Note:
1 .After setting the health airflow function, the position of inlet and outlet grills is fixed.
2.In heating, it is better to select the mode.
3.In cooling, it is better to select the mode.
4.In cooling and dry, using the air conditioner for a long time under the high air humidity,
a phenomenon falling drips of water occurs at the outlet grille .
5.Select the appropriate fan direction according to the actual conditions.
direct to the body.
airflow blows direct to the body.
The cancel of the health airflow function
Press the button of health airflow again, both the
inlet and outlet grills of the air conditioner are opened,
and the unit goes on working under the condition
before the setting of health airflow function.
After stopping, the outlet grille will close automatically.
Notice: Cannot pull direct the outlet grille by hand.
Otherwise,the grille will run incorrectly. If the grille
is not run correctly,stop for a minute and then start,
adjusting by remote controller.

AM
AM AM
AM

Operation
POWER/SOFT Operation
SMART
AUTO
POWER
SOFT
starts POWER function operation.
For twice press,
For each press, is displayed Air conditioner
Press POWER button
disappears,the operation stops.
POWER Operation
When you need rapid cooling, you
can use this function.
POWER
POWER
SOFT Operation
You can use this function when
silence is needed for rest or reading.
starts POWER function operation.
For twice press,
For each press, is displayed Air conditioner
Press POWER button
disappears,the operation stops.
SOFT
SOFT
In SOFT operation mode, fan speed automati
cally takes low speed of AUTO fan mode.
Hints:
During POWER operation, in rapid COOL mode,
the room will show inhomogeneous temperature
distribution.
Long period SOFT operation will cause effect
of not too cool or not too warm.
In COOL mode, fan speed automatically takes
high speed of AUTO fan mode.
To cancel TIMER mode
Just press CANCEL button several times until TIMER mode disappears.
or stop automatically a following times:Before you wake up up in the
morning,or get back from outside or after you fall asleep at night.
Set Clock correctly before starting Timer operation. You can let unit start
TIMER Operation
SMART
1Select your desired operation mode
TIMER ON
Select your desired TIMER ON
Remote controller: " "will flash.
Select your desired TIMER OFF.
Remote controller:
" "will flash.
Time setting.
2
Every time the button
is pressed, time setting
increases or decreases 1 min, if kept depressed,
it will increase rapidly.
.
It can be adjusted within 24 hours.
3Confirming your setting
After setting correct time,
press CONFIRM button
to confirm " "or" "
ON OFF
TIMER ON
TIMER OFF
ON OFF
on the remote controller stops flashing.
TIMER
press TIMER ON button to confirm,follow the
same procedure in "Time setting for TIMER OFF"
Remote controller:
ON OFF
TIMER
press TIMER OFF button to confirm,follow the
same procedure in "Time setting for TIMER ON"
Remote controller:
ON OFF
TIMER
ON OFF
TIMER
Before going to bed,you can simply press the SLEEP
button
and unit will operate in SLEEP mode and bring
Comfortable SLEEP
you a sound sleep.
SMART
AUTO
Press SLEEP button.
Operation Mode
1. In COOL,DRY mode
1 hours after SLEEP mode starts, temp. will
become 1OC higher than temp. setting. After
another 1 hours, temp. rises by 1OC further.
The unit will run for further 6 hours then stops
Temp. is higher than temp. setting so that room
temperature won't be too Iow for your sleep.
SLEEP operation starts
SLEEP operation stops
Approx.6hrs
1 hr Rises 1OC
Rises1OC
Temp.setting Unit stop
In COOL, DRY mode
1 hr
2. In HEAT mode
1 hours after SLEEP mode starts, temp will
become 2
OC lower than temp.setting. After
another 1 hours, temp decrease by 2 C
O
further. After more another 3 hours, temp.
rises by 1 C further. The unit will run for
O
SLEEP
operation starts SLEEP
operation stops
1 hr
1 hr
3 hrs
3 hrs
Rises 1
O
C
Temp.setting Unit stop
In HEAT mode
Decreases 2
O
C
Decreases 2
O
C
further 3 hours then stops. Temp. is lower
than temp. setting so that room temperature
won't be too high for your sleep.
3.In SMART mode
mode adapted to the automatically selected operation mode.
4. In FAN mode
It has no SLEEP function.
be in the state of timing-on,if the two
modes are set up at the same time,
either of their operation time is ended first ,the unit will stop automatically,
5.When quiet sleeping function is set to 8 hours the quiet sleeping time
can not be adjusted.When TIMER function is set,the quiet sleeping
The unit operates in corresponding sleep mode corresponding sleep
function can't be set up.After the sleeping function is set up,if user resets
TIMER function, the sleeping function will be cancelled; the machine will
and the other mode will be cancelled.
Power Failure Resume Function
If the unit is started for the first time, the compressor will not start running
unless 3 minutes have elapsed. When the power resumes after power failure,
the unit will run automatically, and 3 minutes later the compressor starts running.
Note to the power failure resume:
press the sleep button ten times in five seconds and enter function after
hearing four sounds.And press the sleep button ten times within five
seconds and leave this function after hearing two sounds. 4
AM
AM
AM

Operation
iFP Operation
ECO Operation
FRESH Operation
Exhaust the vitiated air from the room, and inhale fresh air.
(This function is unavailable on some models.)
Emergency Operation:
temperature is below 16o
C, do not use it in the
Test operation:
Use this switch in the test operation when the room
normal operation.
your finger from the switch: the cooling
Continue to press the test operation
switch for more than 5 seconds. After
you hear the "Pi" sound twice,
release
Test operation switch is the same as emergency switch.
operation starts with the air flow speed "Hi".
Emergency operation and test operation
Use this operation only when the remote controller
is defective or lost.
When the emergency operation switch is
pressed,the" Pi "sound is heard once, which means
the start of this operation.
In this operation, the system automatically selects
the operation modes,cooling or fan or heat,according
to the room temperature.
It is not possible to operate in dry mode.
Room
temperature
Operation
mode
Designated
temperature
Timer
mode Air flow
ABOVE 23OC
BELOW 23OC
COOLING
HEAT 23OC
26OCNO
NO
AUTOMATIC
AUTOMATIC
(Cooling only uint˅
Room temperature
Operation
mode
Designated
temperature
Timer
mode Air flow
BELOW 23OCFAN 26OCNO AUTOMATIC
Pi
Pi Pi
Press FRESH button“ ” is displayed
on the remote controller and “ ” is
displayed on the display board,and the change-for-fresh-air
function operation begins.
For twice press , the display " "disappears
and the change-for-fresh-air function operation
is canceled.
Automatic adjusting with the environmental temperature, running with power saving.
Press ECONOMY button“ ” is displayed
on the remote controller，
unit will run in ECONOMY operation.
Press ECONOMY button For twice press,
ECONOMY disappears,the operation stops.
The power saving function only works under
the cooling, heating or dehumidifying mode,
after the power saving function is set, press
the sharp, mute, sleep, or smart key to exit
the power saving function.
After the power saving is set, the host machine
will automatically adjust the setting temperature,
and automatically control the switch of the
compressor, which may be inconsistent with
the user’s setting.
The power saving function is more effective
after the air conditioning has been running
for a long time (more than 2 hours)
SMART
ECO
ECO
SMART
iFP
5
The movement of people in the room can be sensed,
which can improve the air adjustment efficiency.
1iFP
Press iFP button“ ” is
displayed on the remote controller
2
Remote controller: BLANK
and “ ” is displayed on the display board,unit will
run in iFP mode.
Every time the button is pressed,
display changes as follows:
Detect the location of the human body,adjust the wind
swing, blow the location where the body is.
The human body sensor is used to detect if the infrared ray is
changing. It may be inaccurate in the following conditions:
The human body keeps still (when reading or watching TV
etc.) or is blocked by barriers like screen, cabinet or glass.
The person is wearing very thick clothes or the person is lying
or sleeping.
A pet is moving frequently, or the wind is blowing the curtains,
or something in the room is swinging frequently.
When several people are located at different positions, or one
person is moving in different areas, no matter whether the wind
is blowing or not, the wind will automatically swing and blow to
multi areas, the wind direction adjustment will be delayed, it
cannot be deflected suddenly while detecting.
In iFP,FOLLOW and EVADE operation mode,
Press“
button，the unit will not operate“ ” mode ,Press“ ”button，
the operation stops.
note˖If the unit didn’t install change-for-fresh-air electrical
engine, change-for-fresh-air function is not available.
After the change-for-fresh-air function is initiated,
the outside air can enter the indoors through the
change-for-fresh-air tube thereby keeping the
indoor air fresh.
About change-for-fresh-air function
Setting the change-for-fresh-air function under
the shutdown status, press the fresh air key and
the remote controller displays the on status of air
flow, low wind, and change-for-fresh-air functions,
and now can set the timing open, timing close and
time control switch.
The dual fresh air has a memory function, which
can be cancelled by pressing the key one time.
Under the smart mode, after the machine has been
running for a while, the dual fresh air function will be
started automatically, it will be automatically stopped
after continuously running for a while.
”
Detect the location of the human body,adjust the wind
swing, avoid the location where the body is.
AM
AM AM
SMART

Cautions
WARNING
Please call Sales/Service Shop for the Installation.
Do not attempt to install the air conditioner by yourself because improper works
may cause electric shock, fire, water leakage.
Connect the earth
cable.
earthing
WARNING
When abnormality such as burnt-small found,
immediately stop the operation button and
contact sales shop.
OFF
Use an exclusive
power source
with a circuit
breaker
ENFORCEMENT
Connect power supply cord
to the outlet completely Use the proper voltage
Do not use power supply
cord in a bundle.
Take care not to damage
the power supply cord.
1.Do not use power supply cord extended
or connected in halfway
STRICT
ENFORCEMENT
STRICT
STRICT
ENFORCEMENT PROHIBITION
PROHIBITION
PROHIBITION
PROHIBITION
Do not start or stop the
operation by disconnecting
Do not channel the air flow directly
at people, especially at infants or
the aged.
Do not try to repair or
reconstruct by yourself.
Do not use for the purpose of storage of
food, art work, precise equipment,
breeding, or cultivation.
CAUTION
Take fresh air occasionally especially
when gas appliance is running at the
same time.
PROHIBITION
STRICT
ENFORCEMENT
Do not operate the switch with
wet hand.
PROHIBITION
PROHIBITION
PROHIBITION PROHIBITION
PROHIBITION
Do not install the unit near a fireplace
or other heating apparatus. Check good condition of the
installation stand
Do not pour water onto the unit
for cleaning
PROHIBITION
Do not place animals or plants in
the direct path of the air flow Do not place any objects on or
climb on the unit.
Do not place flower vase or water
containers on the top of the unit.
Do not insert objects into the air
inlet or outlet.
PROHIBITION
PROHIBITION
PROHIBITION
STRICT
ENFORCEMENT
Check proper
installation of the
drainage securely
the power supply cord
and so on.
2.Do not install in the place where there is any
possibility of inflammable gas leakage around the unit.
3.Do not get the unit exposed
to vapor or oil steam.
6

Trouble shooting
7
Before asking for service, check the following first.
Normal
Performance
inspection
Noise is heard
Phenomenon Cause or check points
The system does not restart
immediately.
Smells are generated.
Mist or steam are blown out.
Multiple
check
Poor cooling
Application temp. range of air conditioner -7oC~43oC.
When unit is stopped, it won't restart
elapsed to protect the system.
When the electric plug is pulled out
and reinserted, the protection circuit
During unit operation or at stop,
a swishing or gurgling noise may
(This noise is generated by
refrigerant flowing in the system.)
During unit operation, a cracking
noise may be heard.This noise is
temperature changes.
Should there be a big noise from
filter may be too dirty.
This is because the system
circulates smells from the interior
During COOL or DRY operation,
This is due to the sudden cooling
Is power plug inserted?
Is there a power failure?
Is fuse blownout?
Is the air filter dirty?
Are there any obstacles before
Is temperature set correctly?
Are there some doors or
Is there any direct sunlight
through the window during the
Are there too much heat sources
or too many people in the room
In dry mode, fan
speed can’t be changed.
In DRY mode, when room
than temp.setting+2oC,unit will
regardless of FAN setting.
Maximum: D.B
10.The appliance must be installed on a strong enough support.
9.Young children should be supervised ensure that they do not
play with the appliance.
8.The appliance is not intended to use by young children or infirm
persons without supervision.
7.The used batteries should be disposed of properly.
6. After installation, the power plug should be easily reached..
5.The wiring method should be in line with the local wiring standard.
4.The distance between the indoor unit and the floor should be
more than 2m.
3. If the fuse on PC board is broken please change it with a fuse
type T. 3.15A/250V.
11.The wiring diagram is attached inside the machine.
2. If the supply cord is damaged, it must be replaced by the
manufacturer or its service agent or a similar qualified
person.
The type of connecting wire is H05RN-F or H07RN-F
Cautions
The machine is adaptive in following situation
1.Applicable ambient temperature range:
Cooling
Heating
Indoor
Outdoor
Outdoor
Indoor
Maximum: D.B / W.B 32
o
C/23
o
C
18
o
C/14
o
C
43
o
C/26
o
C
18
o
C
27
o
C
15
o
C
24
o
C/18
o
C
-7
o
C/-8
o
C
Minimum: D.B / W.B
Minimum: D.B
Maximum: D.B
Minimum: D.B
Maximum: D.B / W.B
Minimum: D.B / W.B
For: T3
Cooling
Heating
Indoor
Outdoor
Indoor
Outdoor
Maximum: D.B / W.B
Minimum: D.B / W.B
Maximum: D.B / W.B
Minimum: D.B
Maximum: D.B
Minimum: D.B
Maximum: D.B / W.B
Minimum: D.B / W.B
29oC/19oC
18oC/14oC
54oC/24oC
18oC
27oC
15oC
24oC/18oC
-7oC/-8oC
For: T1
during cooling operation?
cooling operation?(Use curtain)
windows left open?
inlet and outlet?
Normally it should be cleaned
every 15 days.
run intermittently at LOW speed
temperature becomeslower
indoor unit may blow out mist.
of indoor air.
air such as the smell of furniture,
paint, cigarettes.
air flow in unit operation, air
generated by the casing expanding
or shrinking because of
be heard.At first 2-3 minutes after
unit start, this noise is more noticeable.
will work for 3 minutes to protect the
air conditioner.
immediately until 3 minutes have
If the fuse of outdoor unit on PC board is broken, please change
it with the type of T. 25A/250V.
Application temp. range of air conditioner -7oC~54oC.
T1:
T3: