Haier HW-05LM13 User manual

HW-05LM13
HW-05LN03
001051
TEMPERATURE
1
2
3
4
10
9
8
7
65
FAN ONLY
MIN
COOL MAX COOL
SPEED
LOWHI
OFFON
Wait 3 Minutes Before
Restarting
POWER

1
2
3
3
4
4
5
6-7
6
6-7
8-12
9
9-10
11-12
13-14
15
Installing unit into a window
Wall installations

5

2. MODE Set Switch
2-way
airflow
control paneleasy access filters
5. How The Unit Drains
MODEL: HW-05LM13
HW-05LN01
TEMPERATURE
1
2
3
4
10
9
8
7
65
FAN ONLY
MIN
COOL MAX COOL
SPEED
LOWHI
OFFON
Wait 3 Minutes Before
Restarting
POWER

Fig. # 1
TEMPERATURE
1
2
3
4
10
9
8
7
65
FAN ONLY
MIN
COOL MAX COOL
SPEED
LOWHI
OFFON
POWER
6

Also when you shut off the air conditioner wait for 3 minutes
before turning it on again.
CAUTION:
7
1
2
3

8

HW-05LM13 HW-05LN03
320
340
559
316
130
471.5
373
TEMPERATURE
1
2
3
4
10
9
8
7
65
FANONLY
MIN
COOL MAX COOL
SPEED
LOWHI
OFFON
Wait3 Minutes Before
Restarting
POWER
9

INNER
SILL
OUTER
SILL
I
N
D
O
O
R
S
O
U
T
D
O
O
R
S
WOOD STRIP
MOUNTED ON
TOP OF INNER
SILL
WOOD STRIP
FOR BASEPAN
ANGLE
STORM
WINDOW
FRAME
25mm MAX.
19mm CLEARANCE
1. This unit is designed for installation in standard double hung
windows with actual opening widths of 559mm to 915mm . The
upper and lower sash must open sufficiently to allow a clear vertical
opening of 355mm from the bottom of the sash to the window stool.
2. If storm window presents interference, fasten a 50mm wide wood
strip(not included) (OUTER SILL) to the inner window sill across
the full width of the sill. The wood strip should be thick enough to
raise the height of the window sill so that the unit can be installed
without interference by the storm window frame (STORM WINDOW
FRAME) or wood strip (OUTDOORS) to help condensation to drain
properly to the outside.
3. Install a second wood strip (approximately 150mm long by 38mm
wide and same thickness as first strip) in the center of the outer
sill flush against the back off the inner sill. This will raise basepan
angle .
4. If the distance between STORM WINDOW FRAME and WOOD
STRIP MOUNTED ON TOP OF INNER SILL is more than 25mm,
two of wood strip are not necessary.
I
N
D
O
O
R
S
O
U
T
D
O
O
R
S
INNER
SILL
OUTER
SILL
1
Hereinbefore is just for the demonstration,please adjust the data
according to the actual structure and dimension of the window.
10
3
2

11

12
Also the side louvers should not be blocked.
This is to have proper air circulation in and around the compressor. (See fig.#2)

13
The air filter behind the front grille should be checked and cleaned
at least once every 2 weeks or more often if necessary.
To remove:
1. Open the inlet grille downward by pulling out the top of the inlet grille.
2. Remove the air filter from the front grille assembly by pulling the air
filter up slightly.
3. Clean the filter with warm, soapy water below 40oC.
4. Rinse and gently shake the water from the filter and let it dry before
replacing it.
Always use a soft cloth dampened with water or mild soap
and water solution to wipe the front of the cabinet.
To clean the front panels or the cabinet DO NOT use harsh
chemicals, abrasives, ammonia, chlorine, bleach, concentrated
detergents, solvents or metal scouring pads.
DO NOT use your air conditioner without the air filter in place.
Always unplug your air conditioner before cleaning.
TEMPERATURE
PEED
LOW
OFF
POWER
1
2
3
4
10
9
8
7
6
5
FAN ONLY
MIN
COOL MAX
COOL

14

15
(see page 6)