Haier HWV10XC5 User manual

0010551964
HWV08XC5
HWV10XC5

1

2

10-14
12-14
15-16
16-17
18
7-9
7
7-9
11
11
3

Test power plug before each use:
1. Press ìreset ìbutton.
2 . Press ìtest ìbutton, unit should trip.
3. Press ìresetî button again for use .
Do not use if above test fail.
In the event this device trips , the cause of the malfunction is to
be corrected before further use of the device .
Important:
4

5

1. Temperature Set Knob
This knob adjusts the temperature of the air.
Higher the setting the cooler the air temperature.
With this knob you can set the temperature to
your desired comfort level. Min. Cool being the
warmest and Max. Cool being the coldest.
2. Function Set Knob
With this knob you can control the fan speed
as well as the cooling speed. There are 3 knob
positions on the COOL for you to select from.
LOW will circulate air at the lowest velocity
MED at the middle level and HI will circulate
at the maximum. You have 2 Fan speeds to
choose from HI and LO.
3. 4 Way Air Flow
These air directional louvers let you control
the direction of the airflow in your required
direction. The airflow can be directed
up- down - right side- left side.
4. Window Install Kit.
Enables you to install the air conditioner
in a double hung window. Extra brackets
or support may be needed depending on
your window.
6

OFF
HIGH
FAN
LOW
FAN
HIGH
COOL
MED
COOL
LOW
COOL
--- Turns air conditioner off.
--- High speed fan operation without cooling.
--- Low speed fan operation without cooling.
--- Cooling with high speed fan operation.
--- Cooling with med speed fan operation.
--- Cooling with low speed fan operation.
This automatically controls the temperature of
the indoor air. Turn the knob so that arrow
point to the higher number for greater cooling.
Point the arrow to the lower number for more
moderate cooling. (i.e. the higher number the
greater cooling).
7

FOR NORMAL COOLING
1. Turn the MODE Knob to the HI COOL setting from the LOW COOL setting.
2. Set TEMP control to the desired temperature mark . If the room temperature
is not satisfactory after a reasonable time, adjust the control to a cooler or
warmer setting, as appropriate.
FOR MAXIMUM COOLING
1. Turn the MODE Knob to the HI COOL setting.
2. Set the TEMP control to the highest temperature(10).
FOR QUIETER OPERATION
1. Turn the MODE Knob to LOW COOL setting.
2.Set the TEMP control as needed.
After installing your air conditioner, plug it into the proper electrical outlet
in the wall.
CAUTION:
1. Remember the compressor of your air conditioner will not work when the
temperature goer below 65oF.
2. Also when you shut off the air conditioner wait for 3 minutes before turning
it on again. This is the compressor cycle time.
3. If you have any trouble in operating your air conditioner please refer to
the Trouble Shooting section.
8

OPEN
CLOSE
Ventilation
The ventilation lever must be in the
CLOSE position in order to maintain
the best cooling conditions.
When fresh air is necessary in the room,
set the ventilation lever to the OPEN
position.
When the damper is opened and room
air is exchanged with external air.
Air Direction
The direction of air can be controlled
wherever you want to cool by adjusting
the horizontal louver and the vertical
louver.
HORIZONTAL AIR-DIRECTION
CONTROL
The horizontal air direction is adjusted
by rotating the vertical louver right or
left.
VERTICAL AIR-DIRECTION
CONTROL
The vertical airdirection is adjusted by
rotating the horizontal louver forward
or backward.
9

10

11
1
2
11
3
4
5
67
8 9 14 15
10
12
13
NO. NAME OF PARTS QTY
1
2
3
4
5
6
7
8
9
10
11
12
13
14
15
Curtain
Curtain Frame
Upper Guide
Side Guide
Support Bracket
Bracket
Leveling Bolt & Nut
Bolt
Nut
Side Guide Seal
Form Seal Strip
Window Track Seal
Window Locking Bracket
Screw (Type A)
Screw (Type B)
1
1
1
2
1
1
1
2
2
1
1
1
1
10
11

Window Requirements
1. These instructions are for a horizontal sliding or a casement window.
2. The electrical outlet must be within reach of the power cord.
For installation in a casement window, the window frame assembly and the side of the building must
be adequate to support the weight of the air conditioner.
1. Loosely attach the Support Bracket
to the bottom of Bracket using Bolts,
and Nuts. Attach the Leveling Bolt and
Nut. (Fig. 1)
2. Remove protective backing from Window
Track Seal and apply seal to window track.
(Fig. 2)
3. Measure and lightly mark a line 8-1-14 inches
from window jamb. Center the Support Bracket
assembly on the window track and fasten with 4
Type B screws. (Fig. 2)
4. Put the Support Bracket against the outside wall
and tighten the Bolts on top of the Bracket. Adjust
the Leveling Bolt so that the air conditioner will be
installed with a very slight tilt(about 1/4") downward
toward the outside for proper drainage. Tighten the
nut. (Fig. 3)
NOTE: DO NOT drill a hole in the bottom of the
base pan. The air conditioner is designed to operate
with the bottom of the base pan approximately half-
full of water.
Installing Unit into A Window
Horizontal sliding window Casement window
Horizontal Sliding Window Installation
Bolt
Nut
Bracket
Spport Bracket
Leveling Bolt & Nut
Fig. 1
21" min.
40 1/2" max.
15 1/2"
min.
15 1/2" min.
16 1/2" max.
21 1/2" min.
Fig. 2
Window Jamp
8 1/4 inches
Window Track
Seal
Window Track
Fig. 3
Outside Wall
About 1/4"
12
Type B screw

5. Fasten Side Guides to the sides of the Air
Conditioner using 3 Type A screws per Guide. Start
with first screw at middle of Guide. (Fig. 4)
6. Fasten Upper Guide on the top of the Air
Conditioner using 3 Type A screws. (Fig. 4)
7. Measure height of window opening from top of
Bracket assembly as shown Fig. 5. Subtract 20-3/4
inches. Mark this measurement on Curtain and cut
the curtain. (Fig. 5)
8. Slide Curtain into Curtain Frame. Slide Curtain
Frame assembly into side Guides of the Air
conditioner cabinet. Make sure Curtain is firmly
enclosed on all sides by the Frame. (Fig. 6)
9. Cut side Guide seal into 2 equal lengths. Remove
protective backing and apply it to the rear side of
cabinet Side Guide, starting just below Curtain
Frame assembly. Pinch off excess length so seal is
even with the bottom of side Guide. (Fig. 7)
Fig. 7
Apply weather seal to
side guides jusr below
edge of Curtain
Frame.
Fig. 5
Fig. 4
Fastening Side Guides
Upper Guide
Side Guide
13
Fig. 6
Frame Curtain
Curtain

10. Place Air Conditioner in window opening. It
should sit on Bracket assembly so that Curtain Frame
and cabinet Side Guide are against top and side
window jambs. Mate front of Bracket with Base
Guide attached to the bottom of base pan.
11. Drill 1/8 inch holes in window track through
the existing holes on Base Guide. Screw 4 Type B
screws through the holes. (Fig. 8)
12. If this is a casement window installation, proceed
to Casement Window Installation. If not, slide inner
window sash firmly against side of the cabinet.
13. Drill 1/8" inch hole in window jamb to align
with the existing holes in the Curtain Frame. Attach
Curtain Frame to window frame with 2 Type B screws.
(Fig. 8)
NOTE: Check all seals and plug any remaining air
gaps with a suitable weatherproof caulk.
14. If this is a casement window installation, Proceed
to Casement Window Installation. If not, stuff the
Foam Seal Strip between the vertical sash and the
window glass. (Fig. 9)
15. Attach the L Bracket with a Type B screw. (Fig.
9)
Casement Window Installation
1. Installation procedure is the same as that described in steps 1 through 11 and step 13 of
the Horizontal Sliding Window installation.
2. If the window opening is wider than 15-3/4 inches you will need to install a filler panel.
Make this panel from 3/4 inch thick wood and run it the full length of the window. Attach it
securely to the window frame and paint it to protect it from the weather.
3. Since styles and sizes of casement windows vary widely, it is advisable to have the air
conditioner installed by someone skilled in this type of installation.
NOTE!
Before using the air conditioner secure
the front grille with 1 screw(Type A).
1. Open the inlet grille and remove
the air filter.
2. Fasten the front grille with screws.
3. Reinstall the air filter.
4. Close the inlet grille.
14
Type B screw Fig. 8
Fig. 9
Type B screw Window Track
Base pan
Bracket
Base Guide
Foam seal strip
Window locking
bracket

Always unplug your air conditioner before cleaning.
The air filter behind the front grille should be checked and
cleaned at least once every 2 weeks or more often if necessary.
To remove:
1. Open the inlet grille by pulling out the side of the inlet grille.
2. Remove the air filter from the front grille assembly by pulling the air filter
up slightly.
3. Clean the filter with warm, soapy water below 40oC(104oF).
4. Rinse and gently shake the water from the filter and let it dry before replacing
it.
DO NOT use your air conditioner without the air filter in place.
To clean the front panels or the cabinet DO NOT use harsh
chemicals, abrasives, ammonia, chlorine, bleach, concentrated
detergents, solvents or metal scouring pads. Some of these chemicals
may dissolve, damage and/or discolor your air conditioner.
Always use a soft cloth dampened with water or mild soap
and water solution to wipe the front of the cabinet.
Wipe dry with a soft cloth.
Care and Cleaning Guide
15

To store your air conditioner, after the season, remove the unit from the
window as per the installation guide. Repack the unit in its original box
and store away. If your unit is installed in a wall or you do not intend to
remove it from the window then cover the outside with a winter cover.
This can be purchased from the retailer where you purchased your
air conditioner or from your local hardware store.
Before putting away your unit make sure any water left in the pan is
removed and drained away. Water left in the pan could lead to Rusting
or damage to the electrical connections.
If air conditioner does not operate:
Check if unit is plugged in. The plug may have come loose.
Check if the unit is in "Off" mode.
Air from air conditioner is warm:
The COOL setting may need to be raised.
The temperature outside the room is below 65oF. The compressor will
not cycle on if the temperature outside is below 65oF.
Ice formation on cooling coils:
Outside temperature too cold. Set the unit on fan only
setting to defrost ice.
Lower temperature setting. Temperature setting may be too cold,
Unit BTU may be too high for the room.
16

Air conditioner working but room not cooling:
Room may have appliances that produce heat. Use an exhaust fan to
remove excess heat.
Vent may be in the open position. Vent has to be closed for
optimum cooling.
Redirect the airflow Remove any obstacles.
All doors and windows need to be closed so cool air does
not escape the room.
Air filter may need cleaning.
Unit BTU may be too low for the required cooling area.
On extreme hot & humid days air conditioners may take
a little longer to cool.
You may hear sounds of air movement, water, compressor clicking on and
off or window vibrations. Read Operating Guide- Normal Operating
Sounds. (See page 7)
Air conditioner is making noise when cooling:
Water in the air conditioner cabinet:
This is normal as your air conditioner not only cools but also dehumidifies
the air. If there is water dripping inside the room, check the installation of
the unit. The unit may need to be reinstalled. (See page 12)
17