Haier HLP140E - 2.6 cu. Ft. Portable Vented Electric... User manual

Features
Service Manual
Special No.: SMHLP140E-01 Edition: 2007-4-10
Antibacterial drying, easy and safe
PTC heating, rapid temperature rise
Automatic thermo-limiting, safe and easy
No outdoor air drying, avoiding dust pollution
Computerised control, atuo drying
Tumble Exhaust Type Clothes Dryer
HLP140E
Models:
Version:00.00

CONTENTS
Tumble Exhaust Type Clothes Dryer Model:HLP140E
Contents 1
Product introduction and main features 2
Specification and net dimension 3
Important Safeguards 4
Operating your dryer 6
Parts and structure 10
Wiring diagram 10
Wall Mounting Instructions 11
Maintenance 13
Troubleshooting 14
Maintenance service and trouble shooting 15

Product introduction and main features
3. Exhaust portion
The air from the drum is exhausted through the air outlet grill, filter screen, air impeller and
the exhaust duct. The exhaust direction can be altered by adding an exhaust pipe.
4. Door and control panel structure
The door lock adopts a drawing structure which can be opened by pulling the door handle.
The door switch is installed between the front panel and drum supporter. The projecting arm
at middle part of the door projects or releases the link lever of the door switch to connect or
disconnect the door switch.
The operation is easy and simple. The door switch is installed between the front panel and
the drum supporter. It is safe enough.
I. Product introduction
1. Air inlet structure
In the air inlet portion left lower of the dryer there's a PTC heating device, through which the air
is guided from the air inlet into the drum by rotation of the dryer drum and impeller driven by the
motor. The heating device is a positive temperature coefficient (PTC) semi-conductor heater of
self-control of temperature and high safety provided with a 70 thermo-limiter.
At the air inlet a filter screen is provided to keep air clean and free of impurities.
2. Drum portion
The support plate front of the drum is installed on the dryer cabinet with 6 connectors. A white
felt and a wear-resistant tetrafluoroethylene wearing piece are attached on the drum support
plate. The drum front and rear sealing is made with felt. The drum rear part is mounted with
nuts on the shaft rivetted on the drum support bracket where the air impeller and antiwear
spacer are installed.
The air outlet filter screen is installed in the drum. Take care the filter fixed on the drum with
screws shall be carefully cleaned when cleaning the filter screen.
Antibacterial drying, easy and safe
PTC heating, rapid temperature rise
Automatic thermo-limiting, safe and easy
No outdoor air drying, avoiding dust pollution
Computerised control auto drying
2
Tumble Exhaust Type Clothes Dryer Model:HLP140E

SPECIFICATIONS
Model
Rated voltage frequency
Rated max.Current
Rated max. Capacity
Cycles temperature and
time chioce
120V 60Hz
~
HLP140E
630mm 425mm 685mm
Tumble exhaust type cold air drying and hot air drying
Auto dry Normal heavey,delicate can be choosed
Timed dry: refer to the operating instructions
24kg
3.5kg
Safety device
(a)Safety device (b)Motor overload protector
(c)Thermostat (d)Over-temperature circuit breaker
A
Overall dimensions
Product net weight
Drying mode
3
NET DIMENSION
Unit: mm
Tumble Exhaust Type Clothes Dryer Model:HLP140E

Tumble Exhaust Type Clothes Dryer Model:HLP140E
4
1.Read all instructions before using the appliance.
2.Do not dry articles that have been previously cleaned in, washed in, soaked in, or spotted with gasoline,
dry cleaning solvents, or other flammable or explosive substances, as they give off vapours that could ignite
or explode.
3.Do not allow children to play on or in the appliance. Close supervision of children is necessary when the
appliance is used near children.
4.Before the appliance is removed from service or discarded, remove the door tothe drying compartment.
5.Do not reach into the appliance if the drum is moving.
6.Do not install or store this appliance where it will be exposed to the weather.
7.Do not tamper with controls.
8.Do not repair or replace any part of the appliance or attempt any servicing unless specifically recommended
in the user-maintenance instructions or in published user-repair instructions that you understand and have
the skills to carry out.
9. Do not use fabric softeners or products to eliminate static unless recommended by the manufacturer of
the fabric softener or product.
10.Do not use heat to dry articles containing foam rubber or similarly textured rubber-like materials.
11. Clean lint screen before or after each load.
12.Keep area around the exhaust opening and adjacent surrounding areas free from the accumulation of lint,
dust, and dirt.
When using electrical appliances, in order to reduce the risk of fire ,electric shock, and/or injury , these basic
safety precautions should always be followed:
13.The interior of the appliance and exhaust duct should be cleaned periodically by qualified service
personnel.
14. Do not place items exposed to cooking oils in your dryer. Items contaminated with cooking oils may
contribute to a chemical reaction that could cause a load to catch fire.
16.Do not use or place stove, gas device, water heater, tinder or similarities close to your dryer. Do not install
or store this appliance where it will be exposed to water and/or to the weather.
15.Keep your dryer away from combustible materials (such as gasoline) during operation to prevent the risk
of fire.
17.The tumble dryer is not to be used if chemicals have been used for cleaning.

Tumble Exhaust Type Clothes Dryer Model:HLP140E
5
23.If material has been used with any flammable liquids or solids it should not be used in the dryer until all
traces of the flammable liquids and its fumes have been removed.
25.Do not share a receptacle with other appliances. Do not use it when a plug loosely inserted into a receptacle.
24.This dryer shall be connected to a three-wire, single phase, 120V AC power receptacle more than 15A,
which must be reliably grounded. A leakage protector shall be used, if possible.
21.For appliances with ventilation openings in the base, that a carpet must not obstruct the openings.
19.There has to be adequate ventilation to avoid the back flow of gases into the room from appliances
burning other fuels including open fires, when operating the tumble dryer.
20.Lint is not to be allowed to accumulate around the tumble dryer.
22.Exhaust air must not be discharged into a flue which is used for exhausting fumes from appliances
burning gas or other fuels.
18.The tumble dryer is intended only for drying textile material washed in water.
26.When normally using, the power cord of dryer shall be easily plugged or unplugged by hand. It must be
unplugged during power blackout, moving, not in use or cleaning. Do not plug or unplug the power cord with
wet hands.
27.Always disconnect dryer from electrical supply before attempting any service. Disconnect power cord by
grasping the plug, not the cord.
28.Do not block the exhaust vent when dryer operating to prevent it from overheating or other dangers.
29.Do not let your dryer operate on packing foam. Otherwise it maybe cause fire since heat accumulation or
other external factors.
31.Do not place washed wet clothes in your dryer for a long time not drying them (which may result in water
leakage).
30.Only place sufficiently dehydrated clothes into your dryer for drying to prevent leakage and longer drying
time.
32.Don't touch the intake for the high temperature during the drying cycle.
33.Do not exceed dryer rated Max. Capacity.
34.The appliance must not be installed behind a lockable door, a sliding door or a door with a hinge on the
opposite side to that of the tumble dryer.
35.Do not excessively bend, stretch, twist, bind power cord or put heavy stuff on it. Keep the terminator of
power cord clean. Carefully clean it with dry cloth if dusts accumulated. If damaged, power cord or plug
must be replaced by our service agent or qualified after-sale service person to avoid the risk of danger.

6
Tumble Exhaust Type Clothes Dryer Model:HLP140E
1. Plug the power cord
The appliance shall be supplied with120V,60Hz,
connected to a special receptacle more than
15A (reliablygrounded).
2. Place the dehydrated clothes in your dryer
Check the following items before putting clothes in.
They shall be loaded in such a way that 2-3 pieces
each time and not in a group to avoid tangling, which
is not easy to turn it over resulting in uneven drying
since the clothes were wrapped.
Before drying your clothes
Make sure if clothes have any special requirements and suitable for drying.
Do not dry your clothes in your dryer if the materials of which cannot be dried
in a dryer or they bear the following labels:
Carefully check the clothes to be dried and remove combustible
material such as lighter and match as well as sharp metal items
like coin, hair clip and safety pin maybe mixed with the clothes
and in pockets.
Clothes with zipper or fastener shall be put into your dryer inside
out with zipper zipped and fastener buckled.
Do not tumble dry
Do not tumble dry
Hangtodry
Hang to dry
Drip dry
Drip dry
Dry flat
Dry flat
Dry in the shade
Dry in the shade
Please put clothes into the drum. Avoid clothes being
pressed by the door due to exposure out of the port,
which will cause clothes entangle and door gasket
release and consequently poor drying effect.
Separate dark and light colored items, like you do for washing.
Check for stains that may not have been removed in washing.
Dryer heat may permanently set some stains. Properly dried clothes
will need minimum of care when removed from dryer.
For optimum results,use dryer load of similar fabric, weight and construction. Place
small items in a mesh bag prevent from tangling.Do not overload the dryer. An
average load will fill up half the drum.

7
Tumble Exhaust Type Clothes Dryer Model:HLP140E
Cycle
Dry
Time
Dry
Cool Down
Cycle End
Clean Lint
Normal
Timed Dry
Heavy
Delicate
30
60
90
120
150
Status
A
U
T
O
D
R
Y
Instruction for the operation button
a
3. Drying Procedure Setting
Status and implication of the indicator light
Flash- indicates the program that is functioning
'Dry Time' button
Indicator lights of the status
On- indicates theprogram that isgoing to functionor the statethat has beenchosen
After thepower is on, you can
press in the'DryTime' to
choose the dryingtime directly.
When choose 'Timed Dry', you
can press inthe 'DryTime'
button to choosedrying time
in a rangeof 30, 60,90,120,
150 too.
If the 'Temp' function isset as
'Air-Dry', subsequently the
'Dry Time'will adapt to 30 or
60 minutes.
The implication of the indicatorlights.
Dry
The dryer is working.
Cool Down
The cycle will be completedsoon, and theheater stops heating.
The temperature decreases.
Cycle End
The cycle is completed.
Clean Lint
Remind you cleanthe lint in time each time you dry yourclothes.
Normal Normal drying
Heavy Huge and heavy garments
Delicate Low level heat resistance
'Cycle' button
Timed Dry You can set the drying time
as required
Possible cycle
'PowerOn/Off ' button
'Start/Pause' button
Press in the'PowerOn/Off'button to connectthe
power connector.
Press in the'PowerOn/Off'button to cutoff the
power connector afterthere is power to the machine.
Press in the'PowerOn/Off'button to connectthe
power connector, then press in the 'Start/Pause'button,
if not, themachine will cut off the power connector
by itself.
High
Low
Air-Dry
Temp
Press in the'Start/Pause'
button when thereis power
to the machineto run the
dryer.
Pause when pressin
in the middleof
running.
Start again whenin
status of pause.
Start
Pause
Power
On/Off
'Temp' button
When you choose'Timed dry',
press in the'Temp'button to
choose temperature ina range
of High, Lowand AirDry
(without heating).
'Normal' and 'Heavy'of 'Cycle'
is originally setas 'High'.
'Delicate' is originallyset as
'Low'.

Cycle
Dry
Time Temp
Start
Pause
Power
On/Off
Dry
Cool Down
Cycle End
Clean Lint
Normal
Timed Dry
Heavy
Delicate
30
60
90
120
High
Low
Air-Dry
150
Status
A
U
T
O
D
R
Y
Operation button using procedure and instruction for each step
b
Press in the 'PowerOn/Off' button to run the machine.
Press in the 'Cycle' button to choose appropriate mode.
The clothes dryeris originally setas 'Normal 'when the poweris on .Youmay want to
choose other cycles;please press inthe 'Cycle' button.
If a 'AUTODRY' cycle ischosen, please directly move to step 5.
If a 'TimedDry ' cycleis chosen, pleasefollow up step3,4,5.
Press in the 'Temp' button to choose the appropriate temperature.
The clothes dryeris originally setas 'High' for'Normal' and 'Heavy' mode of
cycle, and 'Low'for 'Delicate' Thetemperature change isforbidden. If youchoose 'Timed dry'
mode of cycle,you can chooseother temperature modefreely.
Power
On/Off
Power
On/Off
Temp
Tumble Exhaust Type Clothes Dryer Model:HLP140E
Press in the 'Start/ Pause'button
Make sure thefront door isproperly closed beforeyou press inthe
'Start/Pause'button, otherwise, theclothes dryer won'tstart and givean alarm.
The machine willstop to workif the frontdoor is openedin middle ofoperation
(including heater andengine). It willcontinue to workafter pressing the'Start/Pause'button
when the frontdoor is closedagain.
There is powerto heating screenafter 30 seconds'spinning of theengine.
Attention
Please choose thedrying time andTemperatureaccording to thequality and quantityof the
garments.
Press in the 'Dry Time'button to set appropriate drying time.
Heating apparatus won't heat in'Air dry'mode, and isproper for down, sweater,
mohair, cottonsweater, cotton-padded clothes. Youmay choose this mode to make garments
fluffier after dried. The machine can also achieve same results for garments left unused for
long in thewardrobe.
For 'High' and 'Low' mode, you canchoose drying timefreely.
For 'Air Dry'mode, only 30 or 60 are available.
Start
Pause
Start
Pause
Dry
Time
Dry
Time
8

There comes a beeper alarm when the drying
procedure is done, the dryer will cut off electricity
by itself after giving alarm.
4. Take out the clothes when the program is finished
Stop heating 10 minutes before the program
finish, cold wind blowing makes the dryer become
cool gradually and the temperature of garments
will be lower.
If you want to take out clothes in the middle of
high temperature operation, please firstly make
the dyer cool and then take out the clothes.
Under normal condition, static electricity comes
as a result of garments made from chemical fiber
rubbing against each other.
5. Pull out the plug
When pull out the plug, please hold the plug top
rather than dragging the line, in case the inner
electric wire was broken or caused a loose
connection.
6. Rinse the filter-net
Referring to Page 13
Tumble Exhaust Type Clothes Dryer Model:HLP140E
9