Haier PFL510W-u User manual

MODEL: PFL510W-U
Order No.
PFL510W-U
2010

PFL510W-U

PFL510W-U

PFL510W-U
(You will see them in the program introduction table)
Signify the program has this course.

FFL510W-U
Extra rinse function:Increase the times of rinse by choosing the function button(at most three times)
Quick wash function:For washing slightly dirty clothes to save water power and time
Intense wash function:For washing relatively dirty clothes to ensure the washing efficiency
Foam self-detect :Automatically add rinse times until the laundry is cleaned when detecting too much foam
Eccentric protection :When spinning,if the clothes are not evenly distributed,the washer will fluff out and
redistribute the clothes and continue spinning after the clothes distribution becomes
even.If the clothes distribution does not become even within the specified time,the washer
will not spin to avoid abnormal vibration.In this case,please check the clothes for intertwist
clothes, the washer may not spin due to eccentric protection.In this case,you can put more
clothes into the washer and make them evenly distributed,then continue spinning.In
addition, it is normal that the program time will prolong because the washer rearranges
and fluffs out the clothes.
Power-down memory :The washer can memorize the program running state in case of power failture or loose
plug during washing and continue the formerly selected program after the power
supply resumes.

PFL510W-U
PFL510W-U
3
54.1
73.8

7
PFL510W-U

8
PFL510W-U

SER V ICE MANUL
Haier Washing Machine
9
PFL510W-U
Program knob
By turning the knob clockwise/counterclockwise, the required program can be
selected. There are 11 programs available. After a program is selected, the
corresponding light will go on.
Power Switch
Press this button to switch on the washing machine. Press it again to switch it off.
Press this button gently for 2 seconds to switch off the machine as buttons are soft
touch sensitive.
Start/Pause Button
When the washing machine is connected to the power socket and a program is
selected, lightly touch this button to start operation. During a wash cycle, touch it
lightly ,operation will stop and the digits on the screen start blinking. Touch it again
to resume operation.
Spinning Speed Setting Button
Touch this button lightly to select the desired speed. When a speed is set, the
corresponding indicator light will be illuminated.
Note: Different water temperatures and spinning speeds can be set for
different laundries. Wash using the default settings if there is no special
requirement.
Washing temperature button
Touch this button lightly to select the desired washing temperature.When a washing
temperature is set, the corresponding indicator light will be illuminated.
Select a temperature according to the type of laundry.

10
PFL510W-U
F
Delay Button
G Detergent distribution drawer
Open the drawer, three compartments can be seen:
Compartment 1: Prewash detergent
Compartment 2: Detergent for programs 1 to 9.
Compartment 3: Softener, conditioning agent, perfume, etc.
H Display
I Intense button
J Extra rinse button
Touch this button lightly, the washing machine will start operation after a period of time
and the corresponding indicator will go on. The range is 0.5-24 hours; each touch of this
button increases a half hour. After the button is set, press the Start/Pause button to start
countdown of the set time (the time is displayed on the screen until the program ends).
Note:The delay time must be longer than the program time;otherwise,the washing machine
will start the wash program directly.
2
1
3
nformation as remaining wash time and error messages will be shown here.
Note: After power is switched on, the display will go on and the remaining wash time
decreases. As the water pressure and temperature may differ, the remaining time maybe
adjusted accordingly. When the laundry is not balanced during spinning, the time may be
automatically prolonged. These are normal phenomena.
If the laundry is heavily soiled, press this button before starting the program. When the
button is pressed, the washing time increases.
Press this button, the washing machine will perform additional rinses. Press the button once
to select one additional rinse. The display will show"P- -1". Press the button repeatedly and
the screen will display "P- -2''or "P- -3'', indicating two or three additional selected rinses.
The "extra rinse light" is activated and flashes during the performance. "P- -1/2/3" is
displayed alternating with the remaining time. The light turns off and the display disappears
when the extra rinse ends.
Note:Select this function when programe 1-9 is selected.

SE RVIC E M ANUAL
PFL510W-U
Haier W ashing Machine
Chapter 5 Wiring circuit
11

SE RVIC E M ANUAL
PFL510W-U
Haier W ashing Machine
Chapter 6 Program Introduction
12
cycle
w
a
s
h
heat
wash
r
i
n
s
e
inlet
rinse
drain
spin
s
o
f
t
end
s
p
i
n
inlet
rinse
drain
spin
drain
spin
fluff
power off
other
func-
-tion
strong
extra
rinse
delay
program
pre
wash
cotton
-ECO
syn-
thetic
wool
Deli-
cate
sport
wash
qu-
ick
MIX
ri-
nse
spin
cotton-
Standard

SE RVIC E M ANUAL
PFL510W-U
Haier W ashing Machine
13
1. How t o st art
Pr e ss t he peed and int ens butt on at t he same time, then put the plug in to the
socket, w a it for about 3 seconds, the LED T
m ac hine ,t hen y ou c an pr ess a rt/ paus t o let was hing m ac hine st a rt te st f un ct i on.
2 . T es t it em
1) when t he door swit ch is c losed f o r three seconds, 88:88 will be displayed.
2) when the main wash va lve al l ows w at er t o l et in f or 3 seconds, 77: 77 wil l be
dis played .
3) when the prewash valve allows water to let in for 3 seconds, 77:77 will be
dis played .
4) when the softy water va lve al l ows w at er t o l et in f or 3 seconds, 77: 77 wil l be
dis played .
5) when the main wash va lv e, the pre w ash valve and a l so the softy water valve
allow wa t er t o let in f or 3 s ec onds at t he same t ime, 77: 77 will be displayed .
6) Heat er runs f or t en s ec o nds, 66:66 will be displayed.
7) t he dr ain pu m p r uns f or about 1 mins, 55: 55 will be displayed
8) the motor runs for 10 seconds with the spi n speed 400rpm, then for ten seconds
wit h the s pin s peed 1000 rp m, 44:44 will be dis play ed

SE RVIC E M ANUAL
Haier W ashing Machine
14
peed and int ens
PFL510W-U
1.Press the extra rinse button and t hen pu t t he plug in t o the socket at the
same time for 4 s ec ond s, and it will ent er t he model- s ele ct ion mode .
3 .If y ou want t o c hange t he m odel again after storage, you can cut off the
NTC and do the cycle adjustment.
4. Model PFL510W-U y ou s hould choos e 1050
5 .Press On /O ff button gent ly f or 2 seconds to switch off the machine as
buttons are sof t touch sensi t ive.
2.The default display shows 1060.Press the speed button tochoose
1460/1450/1260/1250/1060/1050/0960/0950/0860/0850/0760/0750/0660/0650
til
l the needed m odel .T hen pr ess t he t em per at ur e k ey and t he model
can be stored. The model can not be changed a f ter storage.

SE RVIC E M ANUAL
PFL510W-U
Haier W ashing Machine
15

SE RVIC E M ANUAL
Haier W ashing Machine
16
Erro r mess ag e:D oo r i s not p r op erl y s hu t 20s af ter p r og ram is st arte d.
Tr oubleshooting :
Y
PFL510W-U
Cut of f the po wer and th en tu rn on again.
Check the vol t age be tw een br own wire
and blue wi re of door lock, is it bet ween
AC 220-24 0V?

SE RVIC E M ANUAL
PFL510W-U
Haier W ashing Machine
17
E rror me ss age: Drainage error,water not emptied within 6 min.
T rou bleshooti ng:
Check if water is emptied.
NY
Check if the pipe connected to the water
level pressure is jammed.If it is,clean the
pipe.If not,replace PCB
Check if drain pump acts by
touching pump position.
N
Check if drain pump or
drain pipe is jammed.
And open the filter and
clean it.
Y
Cut off the power and choose
spin program to start,then ch-
eck the import voltage of drain
pump,is it between AC 220-
240 V?
N
Y
Replace drain pump.
Cut off the power and pull out
water level pressure switch wire
connection.Set spin program to
start.Check the export voltage
to drain pump,is it between AC
220-240V?
N
Y
The wire between PCB
and drain pump is not
connected properly.
Replace the wire.
Replace PCB.
ERR2

SE RVIC E M ANUAL
PFL510W-U
Haier W ashing Machine
18
E rror me ss age: Temperature sensor is not properly connected or damaged
(display at the end of a program).
T rou bleshooti ng:
N
Y
N
Y
N
Y
Y
Replace PCB.
Cut off power and measure the
resistance of NTC by multimeter,
is it above 1.5 M
NTC exist open circuit.
Replace it.
Check if NTC is connected
properly.
N
Connect NTC well.
Check the wire between NTC
and PBC,are they connected
Connect all wires well.
Disconnect the white wire and
black wire from PCB,and me-
asure if the resistance between
white wire and black wire of
Replace wire.

SE RVIC E M ANUAL
PFL510W-U
Haier W ashing Machine
19
2
3
1
If the water infilow can not reach the washing water level within
8 minutes.

SE RVIC E M ANUAL
PFL510W-U
Haier W ashing Machine
20
E
rror me ss a ge : Motor overheat protection or is damaged.
T roub les hoot i ng:
N
Y
Electromagnetic valve
must be broken,please
replace it.
Y
The wire connected
PCB and inlet valve is
not properly.Please
reconnect if or replace
it.
Turn on power,and set pre-wash
mode,then start.Check the import
voltage of electromagnetic valve by
multimeter,is it between AC220
-240V?
N
Check if export voltage from PCB to
electromagnetic valve,is it between
AC 220-240V?
Replace PCB.
Y
Cut off power and check if motor
wires ,inductance wires are
connected well.
N
Reconnect well.
N
Reconnect motor.
Y
Measure if th e resis t ance of motor
binding b y mu ltimete r ,is it as follo w ed?