Haier XQBM20-E User manual

Names of the parts.............the 2nd cover
Safety precautions .............................1
Installation and adjustment .................3
Install the water inlet hose..................5
Preparation before washing .............7
Put in the laundries ............................8
Add the detergent ..............................9
Close the top lid ...............................10
Select water level .............................10
Select program .................................10
Turn the knob. .................................12
The washing is finished ...................12
Disposal after washing .....................13
Trouble shooting Answer to question......14
Packing list .......................................15
Specification.................the back cover
Contents
Before using
Using process
User's Manual
Fully-auto Washing Machine
XQBM20-E
Please read this manual carefully before using.
Retain it for reference
Please check if the power receptable is earthed
reliably before usage to guarantee your safety.
The manufacturer is not responsible for any
risks occurred owing to disobey these
stipulations.

Meaning and description of the symbols
ʹÓÃ֮ǰʹÓÃ֮ǰ
ʹÓÃ֮ǰʹÓÃ֮ǰ
Before Using
Before Using
Names of the parts
the end connecting
to the water inlet
hose jointer
the end connecting to
the washing machine
Warning sign
Forbidding sign
Contents marked with that symbol
are related to the safety of the
product and the personal safety
of the users. Please operate in
strictconformity to the contents,
otherwise it may cause damage
of the machine or injure the
personal safety of the user.
Contents marked with that symbol
are actions forbidden to perform.
Performing of those actions may
result in damage of the machine
or injure the personal safety of
the user.
Accessories
Adjustable foot
bottom plate
(one)
water inlet hose
(one)
ST4X16
tapping screws
(8 purchase)
Power line
Drain Hose
Handle
Back cover Fixed Foot(3 Pcs)
Water level knob
Water inlet valve
Water absorption
gasket
Top lid
Control panel
seat
lint filter
Inner tub
Pulsator
Cabinet
Cabinet,lower
Control panel filmControl panel film
Lint filter
(one)

Before Using
Before Using
Safety precautions
If the power line is bad, to avoid risk it is required to have it replaced by the technicians
of our special shop or our agent or the after-sale service department. Keep the pin of
the power plug clean.
Do not put the machine at damp place like
the bathroom. Never wash it with water.
Do not use water hotter than 50
In case the washing machine is installed
on ground with carpet, do not block the
ventilation hole with carpet.
soft items
The ventilation holes
at the bottom
Do not let the machine share one receptacle
with other electric appliances. If the power
plug is damaged, or the plugging into the
receptacle is loose, do not use the plug any
more.
Do not wash water-proof laundries like
the raincoat, bike covers etc. to avoid
abnormal vibrations in spinning.
Be sure to earth the earthing wire reliably. When the machine is normally using, please
put the power plug at the location easily to
be inserted and extracted by hand. Be sure
to pull the plug off when there'spower failure,
or the machine is being moved, cleaned or
when it is idle.

2
Do not decompose, repair or alter the
machine by yourself.
Do not put any hot or heavy items (such
as the kettle with hot water ) on the
washing machine.
Do not wash laundries with volatile
materials (such as thinner, petrol etc.)
The handicapped or children without
care shall not use the machine.
Keep the machine away from direct
sunlight and heat source like the heater.
Before Using
Before Using
Do not stretch hands into the working
machine. It is dangerous even if the
rotation is slow. Take special care of
the children.
Petrol
Thinner
Safety precautions
To prevent your laundries and washing
machine from damage,be sure to take out
all of the foreign materials from your pocket,
such as coins,buttons,sand or hair pins etc.
Before washing,please check if the water
tap is open,and if the water inlet pipe is
connected properly.
It is suggested to use low-foaming washing
powder.
Please keep the lint filter in good condition,
and install it to proper position. If the lint
filter is lost or damaged, please contact
the local after-sales service department of
our company.

3
3
Before Using
Before Using
Please install and adjust the machine according to the requirement of the manual. It is
very important to your security and correct operating the machine.
The largest allowed slope of the shank base of the machine is 2 . The slanting or
rough ground will result in unstable running or stoppage of the machine. Please
adjust it with following methods:
Confirm it's horizontal:
Adjust the adjustable foot:
Hang the lead line to confirm if it is horizontal.
After you open the package, please lean
the washing machine gently down on soft
items ( like the towel cloth, blanket, etc. ).
Install the bottom plate to the bottom of
the machine with the eight screws by
a cross screwdriver, then lift the machine
up gently. See to the figure:
Adjust the installation position
soft items
Bottom plate Screw
Loosen Fasten
High Low
adjustable nut
adjustable foot
Back
Front
1.To twist the adjustable foot, please first
lift up the side of the foot slightly, loosen
the adjustable nut, and twist the foot.
2.Fasten the nut after adjustment.
Installation and adjustment

4
1.Lean the machine down gently with the front
surface facing the ground. Loosen the eight
screws by a cross screwdriver.
3.Extend the drain hose from the left side. Push the
drain hose into the groove with hands.
4.Install the bottom plate (as per indicated before),
then lift the machine up gently.
2.Pull out the drain hose from the groove at the
right side.
Back
Front
Bottom plate
Soft item
Use groove at
this side after
direction changing
Page 3
Push the drain hose
into the groove with
hands at this point
Before Using
Before Using
How to change the direction of the drain hose
Usage of the drain hose
1.The height of the drain hose shall be
less than 10cm, or the drainage will not
be smooth, and cost such long time that
the machine may stop at mid way.
2.Do not trample or press the drain hose.
If the drain hose is too long, cut it at mid
point. To make smooth drainage, cut the
front end of the hose slantingly.
4.If extra drain hose is needed, please
make separate purchase. The inner
diameter of the extra hose shall not
less than 26mm, and the length shall
not exceed 1.5m.
If the extra hose is too long, cut it
either at Aor at B point.
The drain hose shall drain smoothly

5
Before Using
Before Using
Install the water inlet hose
Confirm the water faucet
.
.
Note:
1. Insert a new flat washer into the end of the inlet hoses. Firmly put the
washers in the coupling.
You may have to use pliers to tighten the coupling. Do not over tighten
because you may cause damage to the valve.
2. Connect the water inlet hose to the water taps.
3. Connect the other ends to their respective washer inlets located at the
rear of the washer.
Water absorption cushion
Nut of the water inlet hose
Jointer of the water inlet valve
4. Check connection between the adapter of water inlet pipe and water faucet.
1)Slightly move water pipe to check whether is secured.
2)Except for the device,open water faucet to check water leakage.
3)Test and ensure that the connecting matter is indeed normal,then can use
normally.
4)Don't fold water pipe improperly.
5)Check connection between adapter of water inlet pipe and water faucet
before using to avoid water drip due to improper usage of the device.

Confirm if
there's special
requirment for
the laundries.
Clear the pocket.
Take out the
coins , sand,
hairpins etc.
Fasten the
buttons and
zippers.
When the pulsator
is running , the
buttons of the
laundries may
cause noise. For
the sake of
discretion,please
put the laundries
with buttons into
other laundries.
Preparation before washing
1.Connect the water inlet hose and open
the water tap .
2.Confirm that the washing machine is
earthed reliably . Then insert the power
plug into the receptacle. Do not connect
the earth terminal to the gas pipe and
tap water pipe.
3.Put down the drain hose.
The quantity of
the laundries
shall not exceed
the rated value.
The big laundries
like the jeans
shall be put in
loosely.
Using process
Using process
1 Preparation before washing
Pay attention to followings before washing the laundries
a.Please check if the laundries are applicable for washing.
b.Separate those not colorfast from other laundries.
c.For laundries not waterabsorbing,please put them into water with hands.
d.For laundries with much soil,please remove the soil first.You can add detergent on the
part with serious soil directly.It is much easier to remove the soil by that mean.
e.For laundries likely to get lint ball or with long fiber,please first turn the inside out before
putting them into the water.
f.Do not put the laundries polluted with chemicals directly into the washing machine.
g.For those small laundries ,laundries likely to be twisted or worn,and woolen laundries,
please put them into mesh bag before wasing.

Reference weight of the laundries:
working suit up,down
jeans about 800g
The capacity of washing and spinning of the
machine refer to the largest weight of the standard
laundries under dry condition that can be washed
or spinned in one time. One time washing quantity
shall be lower than the rated capacity. The largest
capacity of this machine is 2.0kg.
The thickness, size, type of the cloth will influence
the actual washing capacity. It is suitable for one
time washing to put in reasonable amount of
laundries and the laundries can be turned round in
washing.
Do not select "High" water level for laundries small
than 0.5kg, so as to avoid splashing of water.
To wash thin laundries like the stocking, silk etc.,
please first put them into washing mesh bag (which
can be purchased separately) before wash.
shirt jacket
single bed sheet
Socks
underpants
undershirt
pajamas
blanket
cotton,about 900g
cotton,about
300g
cotton,about
800g
cotton,about 600g
blending,about 50g
cotton,about 70g
cotton,about 180g
Using process
Using process
2 Put in the laundries
cotton,about 1120g
blending coat
(about 800g)

3
Laundries
Quantity(kg) Water level Water quantity
Concentrated powder,
add 25g in each
30L water
2.0-1.0
1.0-0.5
Below0.5
High
Middle
Low
About 30L
About 22L
About 12L
About 40g
About 30g
About 16g
About 25g
About 18g
About 10g
How to use the washing powder
How to use the whitener
Inlet the water to desired level, dilute the
whitener with container, and pour it into the
tub slowly.
Laundries with colors or patterns are more prone
to loose color. Do not use whitener on them.
The whitener should not be made to contact
the laundries directly.
The usage and use level of the whitener
please refer to the User's manual of it.
For the whitener in powder, first dissolve it
then use.
Direct dissolved in the machine
1. Inlet some water.
2. Add the powder. Run for 3 minutes to
dissolve it fully.
3. Put in the laundries. Select suitable
water level.
The instant dissolving of the washing powder:
1. Prepare warm water at 30 in a container.
2. Add the powder while stirring so as to fully
dissolve it.
3. Put in the powder with right quantity accord-
ing to the laundry ,water quantity and water
level.
The above method is only applicable in
manual selection of the water level.
Selection of the water level,water quantity and the quantity of the
washing powder
Add the detergent
Common powder,
add 40g in each
30L water
Using process

Low
Middle
High
Reset
Water level selection
* According to the capacity of the laundries, choose
the three water levels "High" "Middle" " Low" .
* After the water inlet as per the preset water level,
in case additional water quantity is required, please
first set the button to the Reset when the
automatic inlet reaches the water level , you can
turn to the needed water level.
Program Function selection
The dirtiest Choose the process for the heavy and dirtier laundries.
Dirtier Usually overclothes and soft clothes.
Ordinary Thin and soft clothes.
Spin Only for spinning
Wash Washing liquid can be reused.
* If the top lid is not closed , the machine will stop
working in the midway.
Choose the wash process
according to laundries.
Water level selection
Close the top lid Using process

3
* Turn the knob and push-in clockwise for the start and finish of selected process, pull out
the knob to start washing program.
* When the washing is finished, push the knob in.
Note:
When pushing in the knob, the machine is off. When pulling out the knob, the machine is on.
Turn the knob in the push-in state in clockwise direction only.
At the pull-out state, turning the knob will damage the process controller.
The screw of the knob will damage when reversing. This is self-protection of the
process controller. Please operate clockwise after twisting tightly.
Process
Soak Wash
19
About23
About43
About625
5
5
5
5
15
15
5
6
About18
About6.5
About6 spin
The dirtiest(1~6)
Dirtiest
Dirtier(1~6)
Dirtier
Ordinary(3~6)
Ordinary
Rinse(4~6)
Rinse
Spin Total time
Wash(6~7)
Wash
Spin(5~6)
Spin
Rinse
Soak-wash 2 times
Soak-wash 2 times
Soak-wash 1 times
Soak-wash 1 times
Time
1
7
6
5
4
3
2
On
Off
1~2 Marking soak
Marking the beginning
end of thr procedure.
According to the request.
Procedure selector knob (procedure running time: min)
Procedure
Using process

* For the dirtiest clothes, the soak
procedure is designed. At the soaking
state , the pulsator runs and overturn
the laundries several minutes
everytime.
* When no water is reaching the
expected water level, the pulsator
will not run. Please inlet more water
to the selected water level.
* Do not use soak program in
washing the woolen textile.
* Wash the laundries that are prone
to loose colors separately from
other laundries.
Choose the wash procedure according to
the above instruction. Push in the procedure
controller knob and turn it clockwise to the
expected procedure and then pull out the knob,
the machine begins to work.
Dirtiest
Dirtier
Ordinary
Rinse
Wash
Spin
1
7
6
5
4
3
2
On
Off
The washing is finished
When washing process ends , please push in
the process controller knob.
Please notice
Using process

3
Disposal after washing
The filter screen is likely to be blocked
by foreign materials and influences water
inlet. Please clean it with brush every
two months.
If the cabinet is dirty, wipe it with wet soft
cloth
* Do not wash with water directly.
* Wipe with neutral detergent.
* Do not wipe with thinner, petrol, alcohol etc.
1. After washing, close the water tap (you can remove the water inlet hose if needed).
2. Do not store water inside the machine for a long period. Please drain the water
thoroughly after each use.
3. Pull off the power plug before maintenance.
4. Hang up the power cord and drain hose.
5. Wipe off the water drops on the surface of the machine with clean soft cloth.
Open the top lid for a period (about 1 hour), then close it.
Thinner
Alcohol
Petrol
Using process
Figure 2
Figure 3
Figure 1
1. Take off the lint filter
Put hand at the indicated position.
Push down to take it off. ( See to
Figure 1)
2. Clean the lint
Put it in water and clean while it is
still wet.(See to Figure 2)
3. Install the lint filter
After cleaning, insert the bottom
of the lint filter ( marked with
"down side") into the filter frame,
then push the upper part of the
filter in ( marked with " up side ").
(See to Figure 3)
The lint filter must be used during washing.
It must be cleaned in time after each using.
Cleaning the lint filter

Trouble-shooting Answer to question
When spinning ,spin is off and
on .
In the spinning procedure ,
the machine does not spin .
In the process ,drain time is
set. Some minutes later
spinning begins
(If trouble appears, please first pull off the power plug, then check it). Followings are not trouble
sometimes. Please check again before you send it to repair. If there are real troubles, please call
to service department or local dealer . Do not repair it by yourself.
Problems Possible causes Solution
The machine stops in spinning
The draining function is not work-
ing or it's too slow.
The machine does not start.
There's abnormal sound inside
the machine.
The water tap leaks.
The top lid is not closed.
Is the drain hose put down?
Is the drain hose blocked by
foreign material?
Are the laundries put slanting-
ly?
Is the machine slanting?
Is power off?
Is the power plug loose?
Is the machine slanting?
Are the laundries slanting in
spinning?
Is the jointer screw of the water
inlet hose is loose or untighted?
Close the top lid.
Put down the drain hose. Open
and close the top lid once.
Clean the foreign material.
Open and close the top lid once.
Re-order the laundries. Close
the top lid .
Level the machine in right
position. Open and close the
top lid once.
Use it when the power is on.
Insert the power plug tightly.
Level the machine properly.
Re-order the laundries.
Fasten the jointer screw
properly.
There may be some water
flowing out of the drain hose in
the first use of the machine.
It is the water remained in
the factory inspection of
performance.

14
User's manual
Components of the water inlet hose
Fully-auto washing machine
One
One
One
Packing list
Lint filter One

Model
Rated voltage. frequency
Rated washing / spinning capacity
Water level / Water quantity (about)
Max water consumption
Injection pressure
Rated washing power
Rated spinning power
Weight
Dimension (mm)
XQBM20-E
220-240V .50Hz
2.0kg
High / 20L, Middle / 15L, Low / 7L
About 60L (High water level; Normal procedure)
0.03MPa-0.78MPa
225w
200W
About 16kg
L 425 W 416 H 698
Specification