Haier HWM160-B1678S User manual

HWM160-B1678S HWM160-B1678S
0030517257 0030517257
يوﻠﻋ لﻣﺣ ﺔﻟﺎﺳﻏ
كﯾﺗﺎﻣوﺗوأ لﻓ
كﻟﺎﻣﻟا لﯾﻟد
لﯾدوﻣﻟا
ﺔﻟﺎﺳﻐﻟا لﯾﻐﺷﺗ لﺑﻗ ﺔﯾﺎﻧﻌﺑ لﯾﻟدﻟا اذھ ةءارﻗ ﻰﺟرﯾ
.ًﻼﺑﻘﺗﺳﻣ ﮫﯾﻟإ عوﺟرﻠﻟ ﮫﺑ ظﺎﻔﺗﺣﻻاو

Hot water
inlet
valve
Product overview
CONTENTS
(In order to facilitate users to take
and put clothes, the top lid of the
washing machine is designed as
hovering type)
Please understand the shapes of the washing machine and accessories may be
different from the sketch figures in this manual due to product improvement.
Cushion
Fixed feet (2 pieces)
Outer tub cover
Top lid
Inner tub
Pulsator
Detergent tray
Base frame
Screw cover
Adjustable feet (2 pieces)
Top deck
Cabinet
Cold water inlet valve
Control panel
Hook
Power cord
Back cover
Drain hose connector
Drain pump filter cap
(Not to be removed by
the customer)
Product overview
Safety precautions
Installation & adjustment
Before washing
Operation
Operation & wash cycles
Packing list
Specification
Trouble-shooting
1
2
2
2
4
4
4
4
5
7
8
8
9
18
7
8
14
16
19
Description of symbols
Safety warnings
Balancing the washing machine
Installing the bottom plate
Usage the drain hose
Installation of the water inlet hoses
Check the following before washing
Loading detergent
Loading your laundry
Explanation of the display
Installing the lint filter
6
Maintenance
15

Safety precautions
Warning
A separate, earthed power socket is
required for the power supply.
Hold the plug-not the electric cable-when
unplugging the washingmachine.
Do not insert or remove the power plug with
wet hands.
The power plug should be accessible
after the machine installation.
Ensure the plug is removed and the
taps turned off in the followng cases.
Power failure, cleaning, moving,
installation and when not in use.
If the supply power cord is damagd,it must be replaced by the
manufacturer,its service agent or similarly qualified persons
in order to avoid a hazard.
2
Forbidden
60
Do not install this appliance in a
damp or wet environment. Do not
leave wet laundry on the Control
Panel or spray water directly on to
this appliance as this may cause the
washer to malfunctionor cause an
electrical fault.
Do not connect to hot
water higer than
60°C temperature.
Safety precautions
Forbidden
This appliance is not intended for use by
persons (including children) with reduced
physical,sensory or mental
capabilities, or lack of experience
and knowledge, unless they have
been given supervision or
instruction by a person responsible
for their safety.Children should be supervised to
ensure that they do not play with the appliance.
Do not take apart,
repair or alter the
machine by
yourself.
Do not attempt to move washing or place
hands inside washing machine while in
operation. Please ensure children are
supervised around machine to avoid
harm.
Do not leave hot or heavy items on lid
or control panel as this may cause
damage to the washer or make the
washer unsafe to operate.
Do not wash laundry
with chemicals or other
volatile materials(such as
petrol,solvents or thinners)
as this may cause
damage to the
machine.
Keep washer away
from heat sources
such as heater,
stoves or direct sunlight.
3
Description of symbols
Warning sign
Forbidden sign
Contents marked with this symbol are related to the safe use of
the product and the personal safety of the user.
Please operate in accordance to the contents of this manual,to
avoid harm to the user or damage to the machine itself.
Contents marked with this symbol indicate operations or actions
that should not be undertaken by the user.
Performing of such actions may result an injury to the user or
damage to machine itself,and void warranty.
If power cord or other parts of this machine become damaged or faulty, please
contact a technician to have it repaired.. Do not attempt repair by yourself as this
may cause personal harm or void warranty.
The openings must not be obstructed by a carpet.
The new hose-sets supplied with the appliance are to be used and that old hose-sets
should not be reused.
If you are using an extension cord or
a portable electrical outlet device
(not recommended), ensure that it
is positioned so that it does not come
into contact with water or moisture.
Do not wash
water-proof clothing
as this may affect
load balance during
spin cycle(s).
Safety warnings
Please check power socket condition to ensure it has been earthed correctly prior to
installation to ensure your safety

45
8
0.8
Bracket
, the bracket
Installation & Adjustment Installation & Adjustment
Installing the lint filter
Installing the bottom plate
Balancing the washing machine
Install drainage hose
Placement of Drainage Hose
20cm20cm
Installation on an uneven surface can lead to ‘out of balance’ events, instability in
the machine operation, or even failure to successfully complete a wash cycle.
Please refer to the following methods for adjustment:
1.Confirm whether the machine is level.
2.Lift the lid and ensure that the bowl is central to the top deck
opening. Adjust the two front leveling feet as necessary
Note:The distance between the washing machine
and the wall should be at least 20cm.
Not level level
Usage of the drain hose

Installation & Adjustment
67
Before washing
Clear the pockets,
and take out loose
items such as coins,
sand, hairpins etc.
Tie any long
straps or strings,
fasten buttons
and close zippers.
The weight of the
laundry shall not
exceed the rated
capacity of your
machine, loosen
the laundry before
placing it evenly
in the tub.
When the machine
is running, buttons
may cause noise.
To reduce the noise,
turn clothes inside
out or place them in
a laundry bag.
Installation of the water inlet hoses
Check the inlet hose connections
Removing the water inlet hoses
Connection between the water inlet hose and the washer
The new hose-sets supplied with the appliance are to be used
and that old hose-sets should not be reused.

Operation
8
Operation
Mid
Mid
Loading detergent
How to use liquid detergent
1.Prepare warm water (<35°C) in the Inner
tub
.
2.Add
liquid detergent according to the
laundry.
3.Press the start button,Dissolve it completely.
4.Press the pause button, Load laundry.
5.Select the appropriate procedures and water
level, and then start washing
How to use softener
The rated washing capacity refers to the largest dry
weight of a load that can be washed.
Before washing, please make sure that the water level covers the clothes. Adjust
the number of clothes according to the actual situation.
The clothes load should not exceed the height of the metal drum surface.
The thickness, size and type of clothes will influence
the actual capacity.
Do not select more than water level “Mid” for clothes
less than 2.0kg, to avoid splashing of water.
It is recommended that low suds/high efficiency
washing powder is used.
Loading your laundry
The usage and dose of the softener as
per the specifications of softener.
After operation, add washing according
to the method of using liquid detergent
agent
Before washing put the softener into the
detergent box directly.See the above
figure.The softener will put into the
washer when the last rinsing.
After the softener is put in,please don
'
t
place for a long time otherwise softener
may solidify and cause flowing not
smooth.
How to use washing powder
Washing Powder
Softener Inlet
Liquid
Detergent
It is suggested to dissolve detergent before
adding to the tub,see as below:
Adding washing powder Fuzzy Logic Programs
Add washing powder into the detergent
box directly for “Fuzzy logic” programs and
“Delay” program.
Adding washing powder Cotton Wash
It is recommended that washing powder
is dissolved with water and then directly emptied
into the washing machine:
1.Add some water (select the“Low” water level)
2.Add washing powder. Run for
about 30 seconds to fully dissolve the
detergent. Then push the“Start/Pause”
button to pause the wash cycle.
3.Load laundry. Select suitable water level.
Push the “Start/Pause” button again to
recommence washing cycle.
If you select “Express” program, it is
recommended to use liquid detergent
instead of washing powder to ensure
the most effective wash results.
Old or poor quality washing powder may
causing caking in detergent dispenser.
Clean the detergent box periodically to
ensure washing power is evenly distributed
and remove any detergent build up.
Note:
If the detergent specified by the manufacturer is
not satisfactory washing effect . Then choosing
laundry powder, please give priority to qualified
laundry powder that has passed the test.
Push the Power button,set the desired washing program,after setting, push down
the “Start/Pause” button, then hold the “ I ” button and “J” button at the same time
for more than 1 seconds.The digital “CL”, the child lock. All of the buttons are locked,
and will not function.
The function is intended for children safety and preventing the washing program from
accidental changes by children.
Child Lock function
To release the child lock function: push down “ I ” button and “J ” button at the same
time for more than 1s. After
one
beep sound, the child lock function is release.
The child lock light goes out.
Note:After the child lock is released, press the Start/Pause button to open the top lid.
If the top lid is forced to open when washing, the machine will alarm E2 and stop running.
The machine will automatically drain after 10 seconds.If you confirm the safety,
please close the top lid and press "Start/Pause" button to wash the clothes.
The machine will continue to operate.
If a separate washing or rinsing process is selected, the washing machine will drain
automatically after operation
9
I J
Explanation of the display

Operation
10 11
Press the water level button to select the water level you want to set.
When there is water in the tub, it can't automatically detect the cloth quantity.
When Wash and Rinse, press the water level button to replenish the water.
Because of the different wet and dry degree of cloth, the water level judged
will be different. Please choose the water level according to the load.
Water
level
D "Water Level" button
If you choose auto, the machine will detect the cloth quantity and automati-cally
select the suitable water level.
E "Water Temp" button
Water
Temp
Press the “water Temp” button to select your wash temperature.
During ECO, Delicate,Wool and Anti-Crease cycles, “Warm hot” and “Hot”
During Hygiene and Drum clean cycles, “cold”, “warm cold” and “warm”
temperature cannot be chosen.
During Synthetic cycle, “Hot” temperature cannot be chosen
F "Rinse" button
When selecting ECO , there are 6 times spray rinse
When selecting Normal, there are 1 times spray rinse and 1 times deep rinse.
When selecting Extra, there are 2 times spray rinse and 2 times deep rinse.
During ECO cycle, “Normal” and “Extra” rinse cannot be chosen.
During Hygiene and Drum clean cycles, “Eco” and “Normal” rinse cannot be
chosen.
During Express cycle, “Extra” rinse cannot be chosen.
Rinse
After the power is switched on, press it to start the machine.
During working, push it to pause.
During pause, push this button to restart and go on working.
Start/
Pause
B"Start/Pause" button
Push the " Power " button to switch on the power.
Under power-on mode, push it to switch off the power.
If the "Start/Pause" button is not pushed, the machine will switch off
the power automatically after 10 minutes.
A "Power" button
Power
Cotton
A cycle specifically designed to wash sheet loads
Sheets
Mix
Anti Crease
Express
Jeans Washing Jeans
A special cycle for towel loads
Towels
Warmer wash for cotton clothing
A normal wash action for mixed everyday loads including
A warmer wash, reduced spin speed to minimise creasing
Gentle wash action with slow spin speed
Gentle wash action and a medium spin
The water saving cycle
Cleaning the inner and outer tub to avoid the growth of mildew
Do not put any clothes in the inner tub
cottons and blends
Washing t-shirts,shirts laundries
Drum Clean
Wool
Delicate
Synthetic
Program
Quick wash <30min for smaller lightly soiled loads
& brand new clothes
Page12
During the wash cycle, the digital display will show
the time remaining in minutes. (see to page 12)
If an issue occurs, the display will show a user
warning or error code
If a 'Delay start' is selected, the display will show
the total time to cycle completion including the delay period in hours.
Digital display
C "Program" select
Operation
All of the cycles except Express cycle defaults to show "Mid" water level,
The Express cycle defaults to show "Low" water level, and if there is wet
clothing displayed.The "mid" water level needs to be selected manually.
temperature cannot be chosen.
All of the cycles except Drum Clean cycle and Anti-Crease cycle defaults to
show “Auto” water level, you can changed to other water level manually.
The Drum Clean cycle defaults to show “High” water level and cannot to chosen
other water level.The Anti Crease cycle defaults to show “Mid” water level and
cannot to chosenHigh and Low water level.

6
12 13
Operation & Wash Cycles
1
2
Turn the“Cycle” knob to select automatic program
Press the button to switch power on/off
All of the cycles except Drum clean and Anti-Crease have fuzzy function and the
After the detection is completed, the water level is set automatically .
When the washing machine is working, the water level is not optional.
It is necessary to press the "Start/Pause" button before pressing the water level.
Press the button to reset the water level and press the "Start/Pause" button to
start running.
Set the wash temperature in accordance to the requirements of each load.
The suitable temperature between 35-50
Press the button to change the water temp
Separate the fadable clothes separately before putting them into the washing machine.
Even there’s no water in the tub, the spinning will start after a certain period.
During Rinse cycle, only Spin times (spin speed) can be set, all other wash functions
are locked
Press the button to change the water level
3
4
5
Press the button to customise the pre-set options
Rinse Spin
Speed Options Progress
Press the button to select the delay wash program
When the power is turned on, the washing machine Delay procedure is automatically
set to non-startup state.
The laundry process will begin immediately after pressing the Start/Pause button.
Before setting the appointment time, first set up the program and other options,
and then press the Delay button.
The program LEDwill be turned off and the reservation indicator will be turned on.
During the Delay process, press the "Delay" button, and the digital tube shows the
appointment time at the end of the laundry.
To change the operation procedure or cancel the appointment,
the power supply should be cut off and re-selected.
First selectable delay is + 2hours. Increasing in 1 hour
Reservation time is the end of the program
Operating Method of Delay Procedure
increments - Maximum selectable is +12hours.
The wash will finish
in about 10 hours
Operation
Options
H "
Options
" button
Complete ½ the agitate time then complete 2hr soak (with intermittent agit-
ates during soak) , After soak period, continue with the second ½ of agitate
phase. Soak is available on all cycles except Wool and Express cycles.
Soiled+
Soak
Soiled+ & Soak
Favourite
Complete a 15 minute soak sequence ½ way through agitate time. Increase
agitate time by 30%, which is added to the second half of the agitate time.
Soiled + is not available on Drum Clean, Express, Delicate and Wool cycles.
If Soiled+ & Soak are both selected, the soak settings are used with 30%
added to the second 1/2 of the agitate. Soiled+ & Soak are not available on
Drum Clean, Express, Delicate and Wool cycles.
Favourite is a 1s hold now to enable the favourite setting.
Hold the Options and Progress buttons down for 1s the LED will turn
on and the machine will beep. The LED will stay illuminated indicating that the
favourite configuration has been saved.
The next time you selects that cycle, the Favourite LED will illuminate and stay
illuminated for the duration of the cycle.
I "Progress" button
Progress
J"Delay" button
Push the Delay button and the display will show the remaining time for the
cycle to finish (in hours).The indicator flashes to indicate that the delay
function is operating.
Delay start can be set for 2-12hr operation.
NOTE:The delay time displays the number of hours until the selected wash
program will finish (you need deduct wash time from this delay time to calculate
when the wash will start).
Delay
You may change the process when cotton ,Eco,Towels,Sheets,Mix,
Anti Crease,Express,Delicate,Wool,Synthetic, Jeans are selected.
You can’t change the progress when Drum Clean is selected.
G "Spin Speed" button
Use this button to select the spin speed.
No Spin the machine will drain water out but do not spin.
During Delicate, Wool and Anti Crease cycles High spin speed can not be chosen.
Press Spin speed button to choose spin speed in Low, Mid ,High.
Spin
Speed
water level can be adjusted according to the texture and quantity of clothing.

Maintenance
14 15
Remove
Both lint filters must be used during washing.
Tilt upward must be cleaned after each use
Clean the detergent box and set it
on the control panel seat.
1.The method of dismantle:
Tilt upwardand gently pull out.
2.The method of clean: Use a brush
and duster cloth to clean it,
then flush it with water.
3.The method of install : Install it
upwards and aslant and push it in.
and re-install the lint filters as follows:
Remove the power plug before carrying out any cleaning or maintenance.
Clean the lint filter(s) and detergent box after each wash,otherwise it may influence
you using the machine.
The filter at the water inlet valve may
become blocked by impurities in the
water supply.Clean it with a plastic
bristled brush every two months.
If the cabinet is dirty,wipe it with a damp cloth
Do not wash directly with water.
1.After washing cycle has finshed,turn off the water faucet.(If needed,you can remove
the water inlet hose).
2.Do not store water in the washing machine for a long period without completing a
wash cycle.Drain the water completely after each wash.
3.Hang up the power cord and drain hose.
4.Wipe up any drops of water on the surface of the machine and inside the tub.Leave
the lid open for about 1 hour after each wash to evaporate any residual water.
Wipe with a neutral detergent(please check
directions on detergent bottle first).
Do not wipe machine with thinners,petrol,
alcohol or other hash solvents.
1.Push down spring piece of the top lint
filter
,and pull out to remove.(figure1)
2.Pull the back of the lint filter to open
(figure2)
3.Remove any lint in the lint filter.
4.Push the back of the lint filter back into the
front cover.
5.Put the lint filter into filter housing ,
and make it tight.
6.Make sure the lint filter is well installed,or
it can influence performance of the washer.
Install
Dismantle
Down
Up
The front cover of the lint filter
The back cover of the lint filter
Figure 1 Figure 2
Down
Push
Operation & Wash Cycles
Press the button to start the cycle
7

16 17
The display shows F2
The display shows E2-1
Overflow Error.
The door lock alarm.
Trouble-shooting
The display shows FC2
Problem Possible causes What to do
Please contact Customer Care.
The display shows FA
The water level sensor has failed.
Please contact Customer Care.
Please contact Customer Care.
Communication failure
between display board and
Power board.
Common occurrences
The spinning is intermittent after it starts. Redistribute the load evenly.Close the
top lid.
Select spin program,but it does not work.
There maybe water in the drain hose
when first used.
It maybe residual water after performance
inspection by the factory.
The program is setting the drain time,
there will be a pause before the spin
program starts.
Situation Cause
Trouble-shooting
Communication failure
between display board
and motor driver.
The display shows FC1.
Redistribute the load evenly.
Push the Start/Pause button
once.
Level the machine.
The display shows E4.
The display shows FA.
Is the water tap closed or
has the water supply been
interrupted?
Is the water inlet valve
blocked?
Is the water pressure too
low?
Open the water tap. Push
the Start/Pause button once.
Clean the water inlet valve
then push the Start/Pause
button once.
Use after the water
pressure is normal.
The water level sensor
has failed.
The machine
does not work.
Will not
wash
Will not
spin
There are abnormal
sounds inside the machine.
Is the machine level?
Has the laundry been placed
unevenly in the machine?
Are there any foreign objects
inside the bowl?
Level the machine.
Redistribute the load evenly.
Close the top lid.
Remove the foreign object.
Is the power plug inserted
tightly?
Is the top lid closed?
Is the laundry distributed
unevenly in the machine?
Insert the power plug tightly.
Close the top lid.
Redistribute the laundry.
Is there a power failure?
Is the power plug inserted
tightly?
Has the water level reached
preset position?
Wait for the power supply
to be restored.
Insert the power plug tightly.
Wait for the water to fill to
the preset level
Please contact Customer
Care.
If there is a fault or the machine does not operate correctly,remove the power plug
before checking the machine.Using diagnostic list below,please check if the machine
requires a repair.If a repair is required,please contact our customer care team,do not
try to fix it by yourself.
The machine does not drain
or drain slowly.The display
shows E1.
The machine stops running
The display shows E2.
The machine does not drain
or drain slowly.The display
shows ob.
Has the laundry been placed
unevenly in the machine?
Is the machine level?
Is the drain hose blocked?
The top lid is not closed.
Remove the blockage.Push
the Start/Pause button once.
Close the top lid.Push the
Start/Pause button once.
Problem Possible causes What to do
Please contact Customer
Care.
Please contact Customer Care.

Specification
Type
Model
Rared voltage/frequency
Rated washing power
Rated spinning power
Net weight
Gross weight
Dimensions(mm)
Water inlet pressure
Rated Washing capacity
TOP LOAD FULL-AUTOMATIC WASHING MACHINE
220-240V/50Hz
420W
280W
64kg
71kg
16kg
W 640 D 650 H 1076
0.03MPa-1.0MPa
HWM160-B1678S
18 19
Packing list
In Warranty period：Haier Electric Egypt LTD warrants to provide after sales
service as per warranty card;
Out of Warranty period (within lifespan)：Haier Electric Egypt LTD warrants to
provide service at customer expense；
Out of the lifespan：The product still can be used, Haier Electric Egypt LTD will
provide service based on company’s service policy.
Lifespan of the Washing Machine is 10 years.