Hall-Precision SingleCell User manual

SingleCell
INSTRUCTION MANUAL
v1.0
hall-precision.com

SingleCell v1.0- Instruction manual 2
Table of Contents
Introduction� � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � �3
Precautionary Statements� � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � �
Tools Needed� � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � �
Tips � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � �
Build of Materials � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � �4
Assembly � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � �5
Frame� � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � �
Filter � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � �
Grommet� � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � �
PSU Vent � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � �
Door� � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � �
Spool Holder � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � �
Lighting� � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � �
Integration � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � �
Guidelines for Printing with an Enclosure � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � 21
Overview � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � �
PLA� � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � �
PETG � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � �
ABS� � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � �

SingleCell v1.0- Instruction manual 3
Precautionary Statements
Tips
•
• Make sure to hammer in the corner connectors straight otherwise the enclosure will be
•
head. Always use the Washer_v1 with screws when instructed.
•
•
CHOKING HAZARD—Small parts
Not for children under 12 yrs�
SHARP EDGES— Components may
have sharp edges�
Not for children under 12 yrs�
WARNING
WARNING
0-12
Tools Needed
1.
2. Number 2 Phillips Screwdriver (The one you received with your Prusa will work)
3.
4.
Introduction

SingleCell v1.0- Instruction manual 4
Straight Frame
Double Flange Frame
Panel Door
Panel Top
3DPrint - Filter Assem
x 2
Single Flange Frame
Corner Connectors
3DPrint - Knob Assem
3D Print - PSU Vent Assem
Double Flange Frame
Screw
Panel Right
3DPrint - Hinge Assem
Panel Gasket
Double Flange Frame
Grommet
Panel Rear
3DPrint - Spool Holder
Assem
LED Light Strip
1 x 18” 2 x 15” 1 x 18”2 x 22” 2 x 18”
Build of Materials
1 x 15”
F5
1 x 15”
F6
x 1
D
x 1
T
x 1
F
F1
F2
F3
F4
2 x 22”
F7
F8
x 8
C
x 1
L
x 1
K
x 1
V
x 20
W
x 1
R
H
P
x 1
G
x 1
B
x 1
S
x 1
E

SingleCell v1.0- Instruction manual 5
Frame
1� Install 2x corner connectors into the Straight Frame marked ‘F1’.
a)
seat the connector.
b)
c)
2� Install 2x ‘F2
a)
b)
c)
Assembly
F1
C
C
F1
F2
F2

SingleCell v1.0- Instruction manual 6
3� Install 2xF3
the same).
4� Join pieces together.
F3
Assembly
F3
C
C
F2
F2

SingleCell v1.0- Instruction manual 7
5� Install 2x ‘F4’ pieces (they are the same).
6� Install 1x ‘F5’ and 1x ‘F6
Assembly
F4
F4
F6
F5

SingleCell v1.0- Instruction manual 8
7� Slide the panels into grooves. They will remain loose until you secure them with panel gasket at a later
step. Note the cutout positions.
8�
Assembly
Top View
Frame
Groove
Panel
L
B
R
F8
C
C
F7
F7

C
C
F3
T
SingleCell v1.0- Instruction manual 9
9� Slide ‘Panel Top’ into channel/groove.
10�
Assembly
F7
F7

F3
F7
F7
P
P
SingleCell v1.0- Instruction manual 10
11�
don’t get damaged during seating.
12�
Assembly

W
T
F
F
F
F
F
SingleCell v1.0- Instruction manual 11
1�
2�
Filter
3� Mount Cartridge Adapter and Filter Diverter assembly onto Panel Top using 4 screws. Some components
are hidden to increase clarity.
Assembly
Tuck ends into gap

F
F
SingleCell v1.0- Instruction manual 12
4� Mount Fan onto Panel Top using 4 screws.
5�
Assembly
Align tabs and press up. Twist clockwise to secure.
W
F

G
V
SingleCell v1.0- Instruction manual 13
1� Install PSU Cable Grommet
1� Install PSU Vent. Do not overtighten screws or the panel will crack! Some components hidden to
improve clarity.
Grommet
PSU Vent
Assembly
Use 3D printed washers or
panel will crack!
W

H
H
F6
D
H
H
SingleCell v1.0- Instruction manual 14
1� Install 2x Hinge Male parts onto Frame ‘F6’ using 4 screws.
Door
2� 2x Hinge Female parts onto Panel
Door using 4 Screws and 4 Washers.
Assembly
W
W
W
W

D
SingleCell v1.0- Instruction manual 15
3�
4� Thread Knob and Knob Insert together.
Assembly
K

SingleCell v1.0- Instruction manual 16
5� Connect magnets together and then press into the Knob Insert
6�
Assembly
K
K

K
F5
SingleCell v1.0- Instruction manual 17
7�
8�
with the doorknob.
Assembly
Top View
Thread knob and knob insert together so that they
sandwich the panel. Tighten until snug.
Adjust to align withdoorknob.
K
K
K
D

S
S
S
S
S
S
S
S
SingleCell v1.0- Instruction manual 18
1�
Spool Holder
2�
spool holder.
Assembly

E
E
E
E
G
V
SingleCell v1.0- Instruction manual 19
1�
1� Set Enclosure over Printer. Run Power cable through grommet and plug into printer. Position printer so
that the PSU sits snugly against the PSU vent.
Lighting
Integration
Assembly
Start and end run in this
power cable through grommet.
Bottom View

SingleCell v1.0- Instruction manual 20
2�
3�
new enclosure!
Assembly
Table of contents