Halsey Taylor 4592FR User manual

97085C (Rev. SIB - 6/04)
4592FR_FTN 4593FR _FTN
PAGE 1
Halsey Taylor Owners Manual
Freeze Resistant Wall Mount Stone Fountains
IMPORTANT
To assure you install this model easily and correctly,
PLEASE READ THESE SIMPLE INSTRUCTIONS BEFORE STARTING THE
INSTALLATION. CHECK YOUR INSTALLATION FOR COMPLIANCE WITH
PLUMBING, ELECTRICAL AND OTHER APPLICABLE CODES. After installation, leave
these instructions inside the fountain for future reference.
This Freeze Resistant Fountain is shipped in two separate cartons. The second carton
contains the Freeze Resistant Package that is installed on an interior heated wall. Refer to
the Freeze Resistant Package for the rough-in dimensions for installation.
IMPORTANT! INSTALLER PLEASE NOTE.
THE GROUNDING OF ELECTRICAL EQUIPMENT SUCH AS TELEPHONE, COMPUTERS,
ETC. TO WATER LINES IS A COMMON PROCEDURE. THIS GROUNDING MAY BE IN THE
BUILDING OR MAY OCCUR AWAY FROM THE BUILDING. THIS GROUNDING CAN CAUSE
ELECTRICAL FEEDBACK INTO A FOUNTAIN, CREATING AN ELECTROLYSIS WHICH
CAUSES A METALLIC TASTE OR AN INCREASE IN THE METAL CONTENT OF THE WATER.
THIS CONDITION IS AVOIDABLE BY USING THE PROPER MATERIALS AS INDICATED. ANY
DRAIN FITTINGS PROVIDED BY THE INSTALLER SHOULD BE MADE OF PLASTIC TO
ELECTRICALLY ISOLATE THE FOUNTAIN FROM THE BUILDING PLUMBING SYSTEM.
FIG. 1
TUBE IS
SECURED
IN POSITION
SIMPLY PUSH IN
TUBE TO ATTACH
PUSH IN COLLET
TO RELEASE TUBE
PUSHING TUBE IN BEFORE
PULLING IT OUT HELPS TO
RELEASE TUBE
FIG. 2
OPERATION OF QUICK CONNECT FITTINGS
ALL SERVICE TO BE PERFORMED BY AN AUTHORIZED SERVICE PERSON
Installer
NOTE: WATER FLOW
DIRECTION
BUILDING WATER INLET
SERVICE STOP
(NOT FURNISHED)
1/4" O.D. TUBE
WATER INLET
TO COOLER
3/8" O.D. UNPLATED
COPPER TUBE CONNECT
COLD WATER SUPPLY

97085C (Rev. SIB - 6/04)
4592FR_FTN 4593FR_ FTN
PAGE 2
4593FR ROUGH-IN
4592FR ROUGH-IN

97085C (Rev. SIB - 6/04)
4592FR_FTN 4593FR _FTN
PAGE 3
INSTALLATION INSTRUCTIONS
1. This fountain is to be mounted on a smooth, flat, finished wall surface with adequate
support structure.
NOTE: Wall mounting structure must be capable of supporting 300 lb. load on
fountain.
2. Wall should already be framed for the fountain using dimensions shown in rough-in's
on Page 2. Shown dimensions pertain to installation location.
3. Remove bottom cover from fountain and save the screws. Assemble the push rod to
the fountain. (Push rod provided with freeze resistant box)
4. Install the fountain using bolts and washers (not provided). Tighten securely.
5. Attach drain tube to fountain and cut to required length using the freeze resistant box
as a guide.
6. Install freeze resistant box - see box instructions.
7. Install a service stop (not provided) and make water supply connection from the stop to
the strainer in the freeze resistant box. DO NOT SOLDER TUBES INSERTED INTO
THE STRAINER AS DAMAGE TO THE O-RINGS MAY RESULT.
8. Connect fountain water line to freeze resistant box - see box instructions. Replace the
bottom cover.
FIG. 3
ACORN NUT
WASHER
CLOSET SCREW
OR THREADED ROD
(DEPENDING ON WALL TYPE
AND ANCHOR USED)
SUGGESTED CONFIGURATION FOR EXPOSED MOUNTING BOLTS

97085C (Rev. SIB - 6/04)
4592FR_FTN 4593FR_ FTN
PAGE 4
TROUBLE SHOOTING AND MAINTENANCE
Orifice Assy: Mineral deposits on orifice can cause water flow to spurt or not regulate. Mineral deposits may be removed from
the orifice with a small round file not over 1/8" diameter or small diameter wire.
CAUTION: DO NOT file or cut orifice material.
Stream Regulator: If orifice is clean, regulate flow as in Stream Height" instructions above. If replacement is necessary,
see freeze resistant box parts list for correct regulator part number.
Actuation of Quick Connect Water Fittings: Cooler is provided with lead-free connectors which utilize an o-ring water seal.
To remove tubing from the fitting, relieve water pressure, push in on the gray collar while pulling on the tubing. (See Fig.2)
To insert tubing, push tube straight into fitting until it reaches a positive stop, approximately 3/4".
FOR PARTS, CONTACT YOUR LOCAL DISTRIBUTOR OR VISIT OUR WEBSITE WWW.HALSEYTAYLOR.COM
2222 CAMDEN COURT
OAK BROOK, IL 60523
630.574.3500
PRINTED IN U.S.A.
ITEMIZED PARTS LIST
ITEM
NO. PART NO. DESCRIPTION
1
2
3
4
5
6
7
8
9
10
11
12
13
100147140560
100322740560
101570540560
15013C
170705042830
400942308640
56092C
56121C
600985551640
66346C
70793C
75588C
75589C
Drain Gasket
Bubbler Gasket
Drain Gasket
Bubbler Tube Assy.
Basin
Bubbler
Poly Tubing (Cut To Length)
Drain Elbow
Drain Plug Assy.
Drain Tube
Elbow - 1/4"
Slip Joint Nut 1-1/4"
Gasket
FIG. 4
STREAM HEIGHT ADJUSTMENT: Stream height is
factory set at 35 PSI. If supply pressure varies
greatly from this, adjust screw on regulator in
freeze resistant box. Clockwise adjustment will
raise stream and counter-clockwise adjustment
will lower stream. For best adjustment, stream
should hit basin approx. 6-1/2" from bubbler. 4592FR SHOWN
10
6
2
2
3
5
9
4
1
11
813 12
7