Hamlet HXDAS35 User manual

2BAY RAID SYSTEM USB 3.0 DESKTOP
RAID Enclosure for Two 3.5” SATA Hard Drives
USER MANUAL
HXDAS35
www.hamletcom.com

2
Dear Customer,
thanks for choosing an Hamlet product. Please carefully
follow the instructions for its use and maintenance and,
once this item has run its life span, we kindly ask You to
dispose of it in an environmentally friendly way, by
putting it in the separate bins for electrical/electronic
waste, or to bring it back to your retailer who will collect it for free.
We inform You this product is manufactured with materials and
components in compliance with RoHS Directive 2011/65/EU
(2002/95/CE); WEEE Directive 2002/96/CE, 2003/108/CE Italian
Legislative Decree 2005/151 and EMC Directive 2004/108/EC for
the following standards:
EN 55022: 2010
EN 61000-3-2: 2006 + A1: 2009 + A2: 2009
EN 61000-3-3: 2008
EN 55024: 2010
The complete CE declaration of conformity of the product can be
obtained by contacting Hamlet at [email protected].
The information on the importer for your country can be found in the
“About Us” section of the Hamlet website at www.hamletcom.com.
Trademarks and changes
All trademarks and company names mentioned in this manual are
used for description purpose only and remain property of their
respective owners.
The material in this document is for information only and subject to
change without notice.

3
Introduction
Features
•Supports JBOD, RAID0,RAID1,Normal mode
•Enhanced data protection and high-performances storage
•Support with USB3.0 high speed reach up to 5.0Gbps
•Supports Plug-play and Hot-plug
•Support mode select by RAID switch
Specifications
•Inner Interface: SATA
•Outer Interface: USB3.0
•Date Transfer rate: Support USB 3.0 super-speed (5Gbps)
•Complies with USB 2.0 high speed (480Mbps), USB 1.1 Low
speed (1.5Mbps)
•Suitability: 2 x 3.5” SATA HDD
•Supports Plug-play and Hot-plug
•Power Supply: AC 100~240V, 50~60Hz ; DC 12V, 2.5A
•Material: aluminum and plastic
•Cooling Fan: One 25x25mm Cooling Fan
•OS Compatibility: Windows XP/Vista/7/8, Linux and Mac OS
10.4 or above
•Dimension: 200 x 120 x 68 mm (L x W x H)
System Requirements
•Minimum Pentium II/50MHz or Apple G4 processor
•Minimum 64MB RAM
•Windows XP/VISTA/7/8, Mac OS 10.4 and above
•One available USB port
Supported Hard Drives
•One or two 3.5” SATA I/II hard drives (1.5/3.0 Gbps)
•Capacity up to 2TB or more
•Hard drives of identical capacities are recommended
•Supports large volumes in excess of 3TB

4
Package Contents
•Dual bay enclosure 3.5”
•USB 3.0 cable
•Power supply
•Manual
Setting the RAID Mode
RAID (Redundant Array of Independent Disks) is a set of
technology standards for teaming disk drives to improve fault
tolerance and performance.
The RAID mode should be set before installing the drives and then
first formatting the drives.
1. Make sure the power is off.
2. Set the RAID switch and select your preferred RAID mode.
There have 2 mode switch in the inner of the product, it can
form 4 kinds of different ways through these 2 switches, it can
realize 4 kinds of different functions as below.

5
3. Install the hard drives and replace the front panel, then turn on
the power.
4. Format the drives.
Note: Changing the RAID mode will require you to re-format the
drivers. Make sure to backup all existing data first.
Normal Mode (Non-Raid)
Normal mode is the default setting of HDD enclosure and will not
use any RAID mode. In Normal condition, both of the two hard disk
mode inside the enclosure are in independent operation state, and
also will be identified as the two separate hearts in the system,
users can choose any hard drive for storing files. If one piece of
hard disk is damaged, the other piece of hard disk data would not
be influenced.

6
BIG Mode (JBOD/Spanning)
In JBOD mode two hard disk will simply be bound for one, the
merger hard drive performance will be same as single hard disk.
The total capacity of the portable hard disk equal to the sum of two
hard drive capacity. In this mode the system starts to storage from
the first disk and switches to the second hard drive when the
storage space of the first disk is. If one of the two HDDs appears
damaged, then all of the data in the two hard disk will be lost.

7
FAST Mode (RAID 0/Striping)
FAST mode it's also our familiar RAID 0 mode. In RAID 0 state,
data storage is divided into two parts, respectively in two hard disk
storage, then the theory storage speed of hard disk is twice the one
of single block hard disk.
The actual capacity equals to twice the smaller capacity of the one
hard drive (between the two hard disk). The deficiency of RAID 0 is
that any piece of hard disk is failure, the whole RAID on data will
not be restored.

8
SAFE Mode (RAID 1/Mirroring)
Safe mode is also known as RAID 1. In this state two hard drives
are closely mirrored. The actual capacity of portable hard drive
equals to the smaller capacity one, storage speed is same.as a
single block of hard disk. The advantage of RAID 1 lies that any
piece of hard disk stored data losing, others can not lose, its
weakness is the capacity loss of hard drive is bigger.
For this reason the RAID 1 mode is the ideal storage solution for
very important material such as databases or personal data.

9
System Setup
Hard Drive Installation
The drives can be installed at any position, there is no specific
order required.
1. Unlock the switch at the bottom of the case and lift the front
panel upward and away from the housing to remove it.
!
2. Install the hard drives as illustrated below with the top of the
drives, where the label is located, facing each other. Push the
drives lightly into place.
3. Set your preferred RAID mode and then replace the front
panel.

10
Connect to computer
1. Connect one end (type B) of the USB cable into the type B
USB port of your HDD enclosure.
2. Connect the other end of the USB cable (type A) into any
active USB port of the computer.
3. Connect Power supply to the enclosure and power up the
enclosure.
4. Let OS search and install the driver automatically.
5. Use the disk management tool (PC) or disk utility (Mac) to
create a new partition and format the drives.
6. Open “My Computer” to see your external hard drive ready to
use.
Note:
To enjoy USB 3.0 super speed up to 5Gbps, your computer must
be equipped with built-in USB 3.0 ports or a USB 3.0 host PCI-e
card.
It is not possible to add more drives to an existing RAID array
without re-formatting it. When adding additional drivers at a later
point, they will only be detected after the device has been restarted
and the drivers have been re-formatted.