HAMPTON BAY 180-471 User manual

Date Purchased
Store Purchased
Model No.
Serial No.
Vendor No.
UPC
180-471
219054
718212343142
Hampton Bay Lifetime Motor Warranty
The retailer warrants the fan motor to be free from defects in workmanship and material
present at time of shipment from the factory for a lifetime after the date of purchase by the
original purchaser. The retailer also warrants that all other fan parts, excluding any glass or
plexiglass parts, to be free from defects in workmanship and material at the time of shipment
from the factory for a period of one year after the date of purchase by the original purchaser.
We agree to correct such defects without charge or at our option replace with a comparable or
superior model if the product is returned to the retailer. To obtain warranty service, you must
present a copy of the receipt as proof of purchase. All costs of removing and reinstalling the
product are your responsibility. Damage to any part such as by accident or misuse or
improper installation or by affixing any accessories, is not covered by this warranty.
Because of varying climatic conditions in the United States this warranty does not cover any
changes in brass finish, including rusting, pitting, corroding, tarnishing or peeling. Brass
finishes of this type give their longest useful life when protected from varying weather
conditions. A certain amount of wobble is normal and should not be considered a defect.
Servicing performed by unauthorized persons shall render the warranty invalid. There is no
other express warranty. The retailer hereby disclaims any and all warranties,
including but not limited to. Those of merchantability and fitness for a particular
purpose to the extent permitted by law. The duration of any implied warranty which
cannot be disclaimed is limited to the time period as specified in the express warranty. Some
states do not allow limitation on how long an implied warranty lasts, so the above limitation
may not apply to you. The retailer shall not be liable for incidental, consequential, or
special damages arising out of or in connection with product use or performance except
as may otherwise be accorded by law. Some states do not allow the exclusion of incidental
or consequential damages, so the above exclusion or limitation may not apply to you. This
warranty gives specific legal rights, and you may also have other rights which vary from
state to state. This warranty supersedes all prior warranties.
Hampton Bay Lifetime Motor Warranty

Table of Contents
SAFETY RULES....................................................................................................
PACKAGE CONTENTS ........................................................................................
INSTALLING YOUR FAN.....................................................................................
HANGING THE FAN.............................................................................................
ELECTRICAL CONNECTIONS ..........................................................................
FINISHING THE INSTALLATION.......................................................................
BLADE INSTALLATION .....................................................................................
............................................
..............................
CARE OF YOUR FAN..........................................................................................
TROUBLESHOOTING........................................................................................
SPECIFICATIONS...............................................................................................
INSTALLING THE MOUNTING PLATE......................................................
CONNECTING THE LIGHT KIT & GLASS SHADE
OPERATING THE TRANSMITTER......................................
1
2
3
4
5
6
7
8
9
10
11
12
13

1. Before you begin installing the fan, shut power off at the
circuit breaker of the fuse box.
2. Be cautious! Read all instructions and safety information
before installing your new fan. Review accompanying
assembly diagrams.
3. Make sure that all electrical connections comply with
local codes, ordinances, or National Electrical Codes.
Hire a qualified electrician or consult a do-it-yourself
wiring handbook if you are unfamiliar with installing
electrical wiring.
4. Make sure the installation site you choose allows the fan
blades to rotate without any obstructions. Allow a
minimum clearance of 7 feet from the floor and 18 inches
from the tip of the blades to the wall.
5. If you are mounting the fan to a ceiling fan outlet box, use
a U.L. Listed metal octagonal outlet box marked
"Acceptable for Fan Support". Secure the box directly to
the building structure. The outlet box and its support must
be able to support the moving weight of the fan (at least 50
pounds) Do not use a plastic box
6. Caution: To reduce the risk of injury use only the screws
provided with the outlet box in conjunction with the lock
washers provided with the fan.
7. If you are mounting the fan to a joist, make sure it is able
to support the moving weight of the fan (at least 50
1. Safety Rules
8. After you install the fan, make sure that all mounting components
are secured to prevent the fan from falling.
9. Do not insert anything into the fan blades while the fan is
operating.
10. Turn the fan off and wait for the blades to stop completely before
changing the fan direction.
NOTE: The important safeguards and instructions appearing in this
manual are not meant to cover all possible conditions and situations
that may occur. It must be understood that common sense, caution and
care are factors which can not be built into this product. These factors
must be supplied by the person (s) installing, caring for and operating
the unit.
TO REDUCE THE RISK OF FIRE, ELECTRIC SHOCK OR OTHER PERSONAL
INJURY, MOUNT FAN UNLY TO A U.L. LISTED OUTLET BOX OR SUPPORTING
SYSTEM MARKED ACCEPTABLE FOR FAN SUPPORT AND USE MOUNTING
SCREWS PROVIDED WITH THE OUTLET BOX OR IN CONJUCTION WITH THE
LOCK WASHERS PROVIDED WITH THE FAN. MOST OUTLET BOXES
COMMONLY USED FOR FAN SUPPORT OF LIGHTING FIXTURES ARE NOT
ACCEPTABLE FOR FAN SUPPORT AND NEED TO BE REPLACED. CONSULT A
QUALIFIED ELECTRICIAN IF IN DOUBT.
TO REDUCE THE RISK OF PERSONAL INJURY, DO NOT BEND THE BLADE
HOLDERS WHILE INSTALLING, BALANCING THE BLADES OR CLEANING
THE FAN. DO NOT INSERT FOREIGN OBJECTS BETWEEN ROTATING FAN
BLADES.
TO REDUCE THE RISK OF FIRE OR ELECTRIC SHOCK, DO NOT USE THIS
WITH ANY SOLID-STATE SPEED CONTROL DEVICE.
WARNING
NOTE
READ AND SAVE ALL INSTRUCTIONS!

ab
c
Unpack your fan and check the contents. You should have the following items:
.
1 Fan blades (3)
2. Hanger bracket
3. Canopy
4. Canopy cover
5a. Standard downrod assembly
5b. Minimum-length downrod (for close to
the ceiling installation only)
6. Coupling cover
7. Fan motor assembly
8. Blade holders (3)
9. Mounting plate
10. Light plate
11. Glass shade assembly
13 Watt compact fluorescent bulb
12. Receiver+6 wire nuts
13. Transmitter+holder+2 mounting
screws
14.
a. Mounting hardware:
Wire nuts (3)
b. Blade attachment hardware:
Screws (10)
c. Blade holder hardware:
Screws with lock washers (7)
Package Contents 2.
3
1
2
5a
5b
7
69
10
11
12
4
13
14
8
ON

3. Installing Your Fan
Outlet box
Figure 1
Ceiling
joist
Ceiling
joist
Cross brace
Outlet box
Figure 2
Ceiling joist
or cross brace Parallel
wood brace
Provide strong
support
Recessed
outlet box
Hanger
opening must
be facing up-side
Figure 3
Angled ceiling
maximum
17 angle
Outlet box
Figure 4
Ceiling
joist
Hanger bar
(optional)
Hanger
bracket
Phillips screw driver; slotted screw driver; step-
ladder; wire cutters; electrical tape.
If there isn't an existing mounting box, then read the
following instructions. Disconnect the power by
removing fuses or turning off circuit breakers.
Secure the outlet box directly to the building
structure. Use appropriate fasteners and building
materials. The outlet box and its support must be
able to fully support the moving weight of the fan
(at least 50 lbs.). Use a UL Listed metal outlet box.
Do not use a plastic outlet box.
Figure 1, 2 and 3 are examples of different ways to
mount the outlet box.
Note: You may need a longer downrod to maintain
proper blade clearance when installing on a steep,
sloped ceiling. Longer downrods are available from
your Hampton Bay dealer.
To hang your fan where there is an existing fixture
but no ceiling joist, you may need to install a hanger
bar as shown in Fig. 4 (available at your Hampton
Bay dealer).
Tools Required
Mounting Options

REMEMBER to turn off the power.
Follow the steps below to hang your fan
properly:
Step 1. Secure the hanger bracket to the
ceiling outlet box using screws included
with your outlet box, lock wash e r s
included with the fan. (Fig.5)
Step 2. Loosen the two set screws and
remove the hitch pin and lock pin in the top
coupling of the motor assembly. (Fig. 6)
Step 3. Remove hanger ball from downrod
a s s e m b l y b y l o o s e n i n g s e t s c r e w,
removing the cross pin, and sliding ball off
rod. (Fig.7)
Step 4. Carefully feed fan wires up
through the downrod. (Fig. 8) Thread the
rod into the coupling. Next line up holes
and replace lock pin and hitch pin. Tighten
set screws.
Step 5. Slip coupling cover, canopy cover
and canopy onto dow n r o d. ( Fig. 9)
Carefully reinstall hanger ball onto rod
being sure that cross pin is in correct
position, set screws are tighten and wires
are not twisted.
Step 6. Now lift motor assembly into
position and place hanger ball into hanger
bracket. Rotate until the check groove has
dropped into the registration slot and seats
firmly. (Fig. 10) Rod should not rotate if
this is done correctly.
Outlet box
Hanger bracket
Cross pin
Hanger
ball
Downrod
Downrod
Supply
wires
Figure 5
Figure 7 Figure 8
Figure 6
Figure 9
Figure 10
Registration
slot
Downrod
Coupling
*Omit coupling
cover when using
the minimum-length
downrod
cover Canopy
Canopy cover
Set screws
Hitch pin Lock pin
Hitch
pin Lock
pin
Set
screws
Hanger ball
Hanging the Fan 4.

WARNING: To avoid possible electrical
shock be sure electricity is turned off at the
main fuse or breaker box before wiring.
NOTE: The Hand Held Remote or Wall
Control units included with your ceiling fan
are equipped with 16 code combinations to
prevent possible interference from or to other
remote units. The frequency switches on your
Receiver and Transmitter units have been
preset at the factory, please re-check to make
sure the switches on both units are set to the
same positions. The frequency settings should
be changed only in case of interference or if a
second or more remote controlled ceiling fans
are installed in the same structure. Any code
combination will operate the ceiling fan and
light as long as the Receiver and Transmitter
units are set to the same codes (Fig. 11)
Step 1. Insert Receiver into Hanger Bracket
with the flat side of the Receiver facing the
ceiling. (Fig. 12)
S t ep 2. Mo t o r t o Rec e i v e r E l e c tr i c a l
Connections: Connect the WHITE wire from
the fan to the WHITE wire marked "TO
MOTOR N" from the Receiver. Connect the
BLACK wire from the fan to the BLACK Wire
marked "TO MOTOR L" from the Receiver.
Connect the BLUE wire from the fan to the
BLUE wire marked "For Light" from the
Receiver. NOTE: If your ceiling fan features
an UP Light: Connect the ORANGE wire
from the fan to the ORANGE wire marked
"For Up Light" from the Receiver. Otherwise
disregard this step and proceed to secure all
wire connections with the plastic wire nuts
provided. (Fig. 13 )
Step 3. Receiver to House Supply Wires
Electrical Connections: Connect the WHITE
wire (Neutral) from the outlet box to the
WHITE wire marked "AC in N" from the
receiver. Connect the BLACK wire (Hot)
from the outlet box to the BLACK wire
marked "AC in L" from the receiver. Secure
all wire connections with the plastic wire
nuts provided. (Fig. 13 )
Step 4. If your outlet box has a GROUND
wire (Green or Bare Copper) connect this
wire to the Hanger Ball and Hanger Bracket
Ground wires. If your outlet box does not
have a Ground Wire, then connect the
Hanger Ball and Hanger Bracket Ground
Wires together. Secure wire connection with
the plastic wire nut provided. (Fig. 13 )
After all connectors are made, check to make
sure there are no loose strands. As an
additional precaution we suggest to secure
the plastic wire connectors to the wires with
electrical tape.
ON
Figure 11
Figure 12
Receiver
Hanger bracket
5. Electrical Connections
Note: The transmitter only works within 40
feet from receiver.

Fan
Figure 13
Figure 14
Outlet box
Hanger
bracket
Hanger
ball
Canopy
Canopy
cover
White (neutral)
White (neutral)
Green or bare
copper (ground)
White ("AC IN N")
White ("to motor N")
Ground
(green)
(Connect to
ground wire on
hanger bracket
if no house
ground wire
exists.)
Outlet box
Black (hot)
Black ("AC IN L")
Black ("to motor L")
Receiver
Blue ("for light")
Blue (light)
Black (motor)
Step 1. Tuck connections neatly into ceiling
outlet box.
Step 2. Slide the canopy up to ceiling and
over the two crews on hanger bracket. Rotate
canopy clockwise. Next, while holding the
canopy with one hand, slide the canopy cover
over the screws and rotate clockwise until
tight. Note: adjust the canopy screws as
necessary until the canopy and canopy cover
are snug. (Fig. 14)
Finishing the Installation 6.

7. Blade
Step 1. Attach fan blade to the blade
ho l de r us i ng t he scr ew s pr o vi de d .
Tighten screws securely. (Fig. 15)
Step 2. Align holes from blade holder to
motor and secure with 2 screws provided.
Repeat procedure with remaining blades.
(Fig. 15)
Installation
Figure 15
Blade
Blade bracket
Screws
Screws
8. Installing the
Mounting Plate
Step 1. Remove 1 of the 3 screws from the
mounting ring and loosen the other 2 screws.
(Do not remove)
Step 2. Place the key holes from the mounting
plate over the 2 screws previously loosened from
the mounting ring, turn mounting plate until it
locks in place at the narrow section of the key
holes. Secure by tightening the 2 screws
previously loosened and the one previously
removed. (Fig. 16)
Figure 16
Mounting plate
Mounting ring
Screws

REMEMBER: To disconnect the power.
The fan blades must be already attached to
the fan.
Your fan and light kit though pre-wired
have been disassembled at the factory to
ease in shipping. Please follow these steps
to complete the installation of your fan and
light. TO REDUCE THE RISK OF FIRE
D O N O T E X C E E D M A X I M U M
WATTAGE RATING.
Step 1. Loosen (do not remove) the 3
screws from the mounting plate.
Step 2. Raise and hold the light plate close
to the mounting plate and proceed to do the
wire connections. Connect the white wire
connectors from the light plate and fan,
follow the same procedure with the black
wire connectors. (Fig. 17)
Step 3. Place the light plate key holes over
the 3 screws previously loosened from the
mounting plate, turn light plate until it
locks in place at the narrow section of the
key holes. Secure by tightening the 3
screws previously loosened. (Fig. 17).
Step 4.
fluorescent bulbs (included).
Step 5.Raise glass shade and frame up
against the mounting plate and secure by
tightening with screws provided. (Fig. 18)
Install 1 x 13 Watt compact
(Fig. 18)
Figure 18
Glass shade
and frame
Bulb
Mounting
plate
Figure 17
Connector
plugs
Screws
Mounting
plate
Light plate
Connecting the Light Kit & Glass Shade 9.