HAMPTON BAY 26613 User manual

THANK YOU
We appreciate the trust and confidence you have placed in Hampton Bay through the purchase of this ceiling fan. We strive to continually create
quality products designed to enhance your home. Visit us online to see our full line of products available for your home improvement needs.
Thank you for choosing Hampton Bay!
Item # 458-301, 458-633
Model # 26613, 26623
UL Model # 52-WWDIV
USE AND CARE GUIDE
WINDWARD IV 52-INCH CEILING FAN
Questions, problems, missing parts? Before returning to the store call
Hampton Bay Customer Service
8 a.m. - 6 p.m., EST, Monday-Friday
1-877-527-0313
HAMPTONBAY.COM

2
Table of Contents..........................................................2
Safety Information.........................................................2
Warranty.........................................................................3
Pre-Installation ..............................................................3
Installation .....................................................................6
Assembly ....................................................................... 7
Operation .................................................................... 12
Care and Cleaning ...................................................... 13
Troubleshooting.......................................................... 14
Safety Information
1. To reduce the risk of electric shock, ensure the
electricity has been turned off at the circuit breaker or
fuse box before you begin.
2. All wiring must be in accordance with the National
Electrical Code ANSI/NFPA 70-1999 and local electrical
codes. Electrical installation should be performed by a
qualied licensed electrician.
3. The outlet box and support structure must be securely
mounted and capable of reliably supporting a minimum
of 35 lbs. (16 kg). Use only UL-listed outlet boxes marked
“For Fan Support.”
4. The fan must be mounted with a minimum of 7 ft (2 m)
clearance from the trailing edge of the blades to the
oor.
5. Do not operate the reversing switch while the fan blades
are in motion. You must turn the fan off and stop the
blades before you reverse the blade direction.
6. Do not place objects in the path of the blades.
7. To avoid personal injury or damage to the fan and other
items, use caution when working around or cleaning the
fan.
8. Electrical diagrams are for reference only. Light kits that
are not packed with the fan must be UL-listed and
marked suitable for use with the model fan you are
installing. Switches must be UL General Use Switches.
Refer to the instructions packaged with the light kits and
switches for proper assembly.
9. After making electrical connections, spliced conductors
should be turned upward and pushed carefully up into
outlet box. The wires should be spread apart with the
grounded conductor and the equipment-grounding
conductor on one side of the outlet box.
10. All setscrews must be checked and retightened where
necessary before installation.
WARNING: To reduce the risk of personal injury,
do not bend the blade brackets (also referred to as
anges) during assembly or after installation. Do not
insert objects in the path of the blades.
WARNING: To reduce the risk of re or electric
shock, do not use this fan with any solid-state speed
control device.
WARNING: To avoid possible electrical shock,
turn the electricity off at the main fuse box before
wiring. If you feel you do not have enough electrical
wiring knowledge or experience, contact a licensed
electrician.
WARNING: Electrical diagrams are for reference
only. Optional use of any light kit must be UL-listed
and marked suitable for use with this fan.
CAUTION: To reduce the risk of personal injury,
use only the screws provided with the outlet box.
WARNING: To reduce the risk of re or electric
shock, this fan should only be used with fan speed
control part no. Fan28R-240W, manufactured by
Chai Wei Electric Co., LTD.
Table of Contents

MOC.YABNOTPMAH
3
.ecnatsissarehtrufrof3130-725-778-1tcatnocesaelP
The supplier warrants the fan motor to be free from defects in workmanship and material present at time of shipment from the factory for a
period of lifetime after the date of purchase by the original purchaser. The supplier also warrants that all other fan parts, excluding any
glass or acrylic blades, to be free from defects in workmanship and material at the time of shipment from the factory for a period of two
years after the date of purchase by the original purchaser. We agree to correct such defects without charge or at our option replace with a
comparable or superior model if the product is returned. To obtain warranty service, you must present a copy of the receipt as proof of
purchase. All costs of removing and reinstalling the product are your responsibility. Damage to any part such as by accident or misuse or
improper installation or by afxing any accessories, is not covered by this warranty. Because of varying climatic conditions this warranty
does not cover any changes in brass nish, including rusting, pitting, corroding, tarnishing, or peeling. Brass nishes of this type give their
longest useful life when protected from varying weather conditions. A certain amount of “wobble” is normal and should not be considered a
defect. Servicing performed by unauthorized persons shall render the warranty invalid. There is no other express warranty. Hampton Bay
hereby disclaims any and all warranties, including but not limited to those of merchantability and tness for a particular purpose to the
extent permitted by law. The duration of any implied warranty which cannot be disclaimed is limited to the time period as specied in the
express warranty. Some states do not allow a limitation on how long an implied warranty lasts, so the above limitation may not apply to you.
The retailer shall not be liable for incidental, consequential, or special damages arising out of or in connection with product use or
performance except as may otherwise be accorded by law. Some states do not allow the exclusion of incidental or consequential damages,
so the above exclusion or limitation may not apply to you. This warranty gives specic legal rights, and you may also have other rights
which vary from state to state. This warranty supersedes all prior warranties. Shipping costs for any return of product as part of a claim on
the warranty must be paid by the customer.
Contact the Customer Service Team at 1-877-527-0313 or visit www.hamptonbay.com
Pre-Installation
SPECIFICATIONS
Size Speed Volts Net
Weight
Gross
Weight Cube Feet
52”
Low
120 20.2 lbs
(9.2kgs)
23.1lbs
(10.5kg) 1.7’
Medium
High
12
30
57
204
143
106
2448
4289
6057
NOTE: These are approximate measures. They do not
include the Amps and Wattage used by the light kit.
TOOLS REQUIRED
Phillips
screwdriver
Flat blade
screwdriver
Adjustable
wrench
Electrical
tape
Wire
cutter
Step ladder
Warranty
AIRFLOW
CFM
FAN POWER
CONSUMPTION
(WITHOUT
LIGHTS) WATT
AIRFLOW EFFICIENCY
(HIGHER IS BETTER)
CFM/WATT

4
HARDWARE INCLUDED
NOTE: Hardware not shown to actual size.
Part Description Quantity
AA Blade attachment screw 16
BB Wire connecting nut
CC Hanger pin 1
DD Locking pin 1
Part Description Quantity
EE Balancing kit 1
Close-to ceiling mount
hardware (rubber gasket) 1FF
AA BB CC DD EE
FF
Pre-Installation (continued)
3

MOC.YABNOTPMAH
5
.ecnatsissarehtrufrof3130-725-778-1tcatnocesaelP
Pre-Installation (continued)
PACKAGE CONTENTS
Part Description Quantity
A Slide-on mounting bracket
(inside the canopy)
1
B Ball/downrod assembly 1
C Canopy with canopy ring
attached 1
D Fan-motor assembly 1
Light kit tter assembly Light bulbs,13-Watt maximum E 1
Part Description Quantity
F Decorative motor collar cover 1
G Blade 5
H
J
I
Remote control/receiver (batteries
included) 1
Glass bowl 1
2
IMPORTANT: This product and/or components are
governed by one or more of the following U.S. Patents:
5,947,436; 5,988,580; 6,010,110; 6,046,416, 6,210,117 and
other patents pending.
Part Description Quantity
E
B
J
H
I
BB
G
F
D
A
C
B

6
Installation
MOUNTING OPTIONS
WARNING: To reduce the risk of re, electric shock, or
personal injury, mount the fan to an outlet box marked
acceptable for fan support using the screws provided with the
outlet box. An outlet box commonly used for the support of
lighting xtures may not be acceptable for fan support and
may need to be replaced. If in doubt, consult a qualied
electrician.
If your ceiling fan does not have an existing UL-listed mounting
box, then install one using the following instructions:
ƑDisconnect the power by removing the fuses or turning
off the circuit breakers.
ƑSecure the outlet box directly to the building structure.
Use the appropriate fasteners and materials. The outlet
box and its bracing must be able to fully support the
weight of the moving fan (at least 35 lbs.). Do not use a
plastic outlet box.
The illustrations below show three different ways to mount the
outlet box.
If the canopy touches the downrod, then remove the decorative
canopy bottom cover, and turn the canopy 180° before attaching
the canopy to the mounting plate.
To hang your fan where there is an existing xture but no ceiling
joist, you may need an installation hanger bar as shown above
(available at any Home Depot store).
Outlet Box
Outlet Box
Provided Strong
Support
Ceiling Mounting
Plate
Recessed
Outlet Box
NOTE: You may need a longer downrod to maintain proper
blade clearance when installing on a steep, sloped ceiling.
The maximum angle allowable is 30° away from horizontal.
Outlet Box
Hanger Bar

motor housing (D).
motor housing (D).
motor housing (D).
(GG)
GG
Failure to properly install the locking pin
could result in the fan becoming loose and possibly
falling.

8
Assembly – Hanging the Fan
4Attaching the fan to the electrical
box 5Hanging the fan
ƑPass the 120-Volt supply wires through the center hole
in the mounting bracket (A).
ƑInstall the ceiling mounting bracket on the outlet box by
sliding the mounting bracket (A) over the two screws
provided with the outlet box. If necessary, use leveling
washers (not included) between the mounting bracket
(A) and the outlet box. Note that the at side of the
mounting bracket (A) is toward the outlet box. When
using close-to-ceiling mounting, it is important that the
mounting bracket be level.
Ƒ
Securely tighten the two mounting screws.
ƑCarefully lift the fan-motor assembly (D) up to the
mounting bracket (A).
ƑSeat the hanger ball portion of the ball/downrod assembly
(B) in the mounting bracket socket. Ensure that the tab on
the mounting bracket (A) socket is properly seated in the
groove in the hanger ball. If using close-to-ceiling
mounting, hang the fan on the hook provided by utilizing
one of the holes at the outer rim of the ceiling canopy.
WARNING: To reduce the risk of re, electric shock, or
other personal injury, mount the fan to an outlet box or
supporting system marked acceptable for fan support, and
use the mounting screws provided with the outlet box.
WARNING: The hook as shown is only to balance fan while
attaching wiring. Failure to hang as shown may result in the
hook breaking, causing the fan to fall. Hook must pass from
inside to outside of canopy.
A
Assembly -Close-To-Ceiling Mounting
ƑRemove the decorative canopy bottom cover (L) from the
canopy (C) by depressing the three studs.
ƑRemove three of the six screws and lock washers (every
other one) securing the motor collar to the top of the fan
motor housing.
ƑPlace the rubber gasket (FF) over the remaining three
screws, route the wires exiting the top of the fan motor
through the canopy ring (make sure the slot openings are
on top), then proceed to place the ceiling canopy (C) over
the collar at the top of the motor.
ƑAlign the mounting holes with the holes in the motor and
fasten, using the three screws and lock-washers removed
previously. Tighten the mounting screws securely.
L
C
C
D
FF
ƑRemove canopy ring from the canopy (C) by turning the
ring to the right until it unlocks.
Ƒ
Ƒ
Remove the mounting bracket (A) from the canopy (C) by
loosening the four screws on the top of the canopy (C).
Remove the two non-slotted screws and loosen the
slotted screws.
1
Close-to-Ceiling Mounting
A
D
A
B
D

NOTE:
The frequencies on your receiver and remote control
have beet preset at the factory. Before installing the receiver,
make sure the dip switches on the receiver and remote control
are set to the same frequency. The dip switches on the remote
control are located inside the battery compartment.
MOC.YABNOTPMAH
9
.ecnatsissarehtrufrof3130-725-778-1tcatnocesaelP
Assembly – Hanging the Fan (continued)
6Making the electrical connection 7Mounting the fan
IMPORTANT: Use the wire connecting nuts supplied with
your fan. Secure the connectors with electrical tape and
ensure there are no loose strands or connections.
ƑConnect the ground conductor of the 120-Volt supply (this
may be a bare wire or a wire with green colored insulation)
to the green ground lead(s) (II) of the fan.
ƑConnect the fan motor white wire (LL) to the receiver (NN)
white wire (LL) using a wire nut.
ƑConnect the fan motor black wire (KK) to the receiver (NN)
black wire (KK) using a wire nut.
ƑConnect the fan motor blue wire (JJ) to the receiver (NN)
blue wire (JJ) using a wire nut.
ƑConnect the receiver (NN) red wire (OO) to the supply black
(hot) wire (KK) using a wire nut.
ƑConnect the receiver (NN) white wire (LL) to the supply white
wire (neutral) (LL) wire using a wire nut.
ƑAfter connecting the wires, spread them apart so that the
green (II) and white wires (LL) are one side of the outlet box
(MM) and the black wire (KK) is on the other side.
ƑTurn the wire connecting nuts upward and carefully push
the wiring into the outlet box (MM).
ƑAlign the locking slots of the ceiling canopy (C) with the
two screws in the mounting bracket (A). Push up to engage
the slots, and turn clockwise to lock the canopy in place.
ƑFirmly tighten the two mounting screws.
ƑInstall the remaining two mounting screws into the holes in
ƑInstall the decorative canopy ring by aligning the ring's
slots with the screws in the canopy (C). Rotate the ring
counter-clockwise to lock in place.
the canopy (C) and tighten rmly.
WARNING: Each wire nut supplied with this fan is designed
to accept up to one 12-guage house wire and two wires from
WARNING: When using the standard ball/downrod
mounting, the tab in the ring at the bottom of the mounting
plate must rest in the groove of the hanger ball. Failure to
properly seat the tab in the groove could cause damage to
the wiring.
the fan. If you have larger than 12-guage house wiring or
more than one house wire to connect to the fan wiring,
consult an electrician for the proper size wire nuts to use.
Ƒ
Close-To-Ceiling Mounting
Carefully unhook the fan from the mounting bracket (A) and
align the locking slots of the ceiling canopy (C) with the two
screws in the mounting bracket (A). Push up to engage the
slots and turn clockwise to lock the canopy in place.
Immediately tighten the two mounting screws rmly.
ƑInstall the remaining two mounting screws into the holes in
the canopy (C) and tighten rmly.
ƑInstall the decorative canopy ring by aligning the ring's
slots with the screws in the canopy (C). Rotate the ring
counter-clockwise to lock it in place.
NN
KK LL
OO
LL
KK
LL
JJ
II
JJ
KK LL
LL
MM
D
C
A
D
C
A
The locking slots of the ceiling canopy are
provided only as an aid to mounting. Do not leave the fan
assembly unattended until all four canopy screws are
engaged and rmly tightened.
WARNING:

01
Assembly – Attaching the Fan Blades
8Attaching the fan blades
Ƒ
Ƒ
Attach the blade (G) to the fan motor housing (D) by rst
inserting the blade (G) into the slot in the side of the fan
motor housing (D).
Start a screw (AA) into the bracket. Repeat for the two
remaining screws.
ƑTighten each screw (AA) securely.
ƑRepeat these steps for the remaining blades (G).
G
AA
C
D

MOC.YABNOTPMAH
11
.ecnatsissarehtrufrof3130-725-778-1tcatnocesaelP
Assembly – Attaching the Accessories
9
Installing the light kit
Ƒ
ƑConnect the blue wire exiting the bottom of the fan motor
assembly with the black wire from the top of the light kit
tter assembly (E).
Connect the white wire exiting the bottom of the fan motor
assembly with the white wire from the top of the light kit
tter assembly (E).
ƑRemove one screw from the black bracket below the fan
motor assembly. Loosen, but do not remove the other two
screws.
ƑAttach the light kit assembly (E) to the fan motor assembly
by securing with the two screws loosened in rst step.
Push the light kit assembly (E) up to engage the screw heads in
the screw slots and turn to secure. Tighten each screw rmly.
ƑWith the power off, install the two uorescent bulbs (J)
(Max. 13W, provided) into the light bulb sockets.
ƑPlace the glass shade (I) into the light kit assembly,
aligning the three at areas on the top ange of the glass
shade (I) with the three raised dimples in the light kit
assembly. Turn the glass shade (I) clockwise until it stops.
CAUTION: To reduce the risk of electrical shock,
disconnect the electrical supply circuit to the fan before
installing the light kit.
WARNING: Do not overtighten when installing the glass
shade into the light kit assembly. When replacing the bulbs,
allow the glass shade to cool completely before removing.
CAUTION: Over lamping the fan will result in the fan lights
shutting down until the proper wattage of bulbs are installed.
Reset the lights by turning off the light and replacing the
bulbs with the correct wattage bulbs.
G
E
I
J
E
G

21
Operation
Controller Model: FAN28R-240W
Installing the receiver
Operating the Fan Remote Control
Setting the code
To set the code on the remote control:
Remove the battery cover by pressing rmly on the arrow and
sliding the cover off.
Slide the code switches to your choice of either up or down.
The factory setting is up.
To set the code on the receiver:
Slide the code switches to the same position as set on your
remote control.
Replace the battery cover on the remote control.
Your new ceiling fan is equipped with a remote control to operate
the speed, direction, and lights. For more information on how to
install the remote control, see the remote control instructions along
with the remote control components.
Appropriate speed settings for warm or cool weather depend on
factors such as the room size, ceiling height, and number of fans.
Load 4 “AAA” 1.5v batteries (included) into the battery
compartment.

Position the receiver at side up and perpendicular to the
mounting bracket (A).
Position the supply wires to the left side of the mounting bracket
(A), and position the fan wires to the right side.
Partially insert the remote control receiver (H) (at side up) until
one end rests on the ball/downrod assembly (B).
Use the FAN AUTO button to select Manual or Auto operation of
your fan.
MANUAL mode lets you control the speed using the remote control.
AUTO mode adjusts the speed automatically based on the temperature
setting that you select.

CAUTION:
This device complies with part 15 of the
FCC rules. Changes or modications not expressly
approved by the manufacturer could void your
authority to operate this equipment.
NOTE: Do not wait for the fan to stop to press the reverse
button. The fan will not reverse if the fan is not moving.
WARNING: To reduce the risk of re or electric shock,
remember to disconnect power. The electrical wiring must
meet all local and national electrical code requirements. The
electrical source and fan must be 115/120 volt, 60Hz.
A
C
B
H
1 2 3
ON
4
1 2 3
ON
4
effect. This allows you to set your air conditioner on a warmer
setting without affecting your comfort.
the ceiling. This allows you to set your heating unit on a cooler
setting without affecting your comfort.
Ƒ
Ƒ
Ƒ
Ƒ
Ƒ
Ƒ
Ƒ
Ƒ
Ƒ

MOC.YABNOTPMAH
31
.ecnatsissarehtrufrof3130-725-778-1tcatnocesaelP
Care and Cleaning
ƑBecause of the fan’s natural movement, some connections may become loose. Check the support connections, brackets, and blade
attachments twice a year. Make sure they are secure. It is not necessary to remove the fan from the ceiling.
ƑClean your fan periodically to help maintain its new appearance over the years. Do not use water when cleaning, as this could damage
the motor, or the wood, or possibly cause an electrical shock. Use only a soft brush or lint-free cloth to avoid scratching the nish. The
plating is sealed with a lacquer to minimize discoloration or tarnishing.
ƑYou can apply a light coat of furniture polish to the wood for additional protection and enhanced beauty. Cover small scratches with a
light application of shoe polish.
ƑYou do not need to oil your fan. The motor has permanently lubricated sealed ball bearings.
WARNING: Make sure the power is off before cleaning your fan.
Operation (Continued)
OFF
HIGH
MEDIUM
LOW
NOTE: You have 6 second to set the sleep timer. If you do
not perform any entries during this time, the light timer
display will be turned off automatically. To reset, press the
TIMER button again.
Example:
Set temperature 72˚ F Room temperature 71˚ F off
Set temperature 72˚ F Room temperature 72˚ F Low
Set temperature 72˚ F Room temperature 76˚ F Med
Set temperature 72˚ F Room temperature 80˚ F High
 In MANUAL mode, use the blue button to adjust the speeds by
pressing and releasing the button to change speeds as follows:
The orange light button turns the fan lights on or off. The LIGHT
TIMER and FAN TIMER buttons set the sleep timer from 0.5 to
24 hours.
Press and release the orange light button to turn the light on
and off.
To set the sleep timer, press the LIGHT TIMER or FAN TIMER
button once, and the timer symbols will be displayed on the
LCD screen.
Use the TEMP./SET/HOUR buttons to set the desired sleep time
from 0.5-24 hours. The light or fan both will be turned off
automatically when the preset Time expires. If the fan is in the
FAN AUTO mode, it will return to MANUAL mode when the sleep
timer expires.
Use the LIGHT-Delay button to activate the light delay function.
The light will automatically shut off in 3 minutes.
Ƒ
In AUTO mode, press the FAN AUTO button to display FAN AUTO
on the LCD screen.
Use the TEMP./SET/HOUR BUTTONS to set the desired temperature
from 59°F-99°F.
The fan will start automatically on low speed when the room
temperature is equal and up to 4° F over the set temperature.
The speed will change between low, medium, and high as the
temperature increases or decreases in 4° F increments.
Ƒ
Ƒ
Ƒ
Ƒ
Ƒ
Ƒ

41
Troubleshooting
Problem Solution
The fan will not start ƑCheck the main and branch circuit fuses or breakers.
ƑCheck the line wire connections to the fan and switch wire connections in the switch housing.
The fan is noisy
ƑEnsure all motor housing screws are snug.
ƑCheck the battery in the remote control.
ƑEnsure you are in the normal range of 10-20 feet.
ƑTurn the power off and ensure that the dip switches settings are the same on the remote control and
receiver.
ƑEnsure the screws that attach the fan blade bracket to the motor hub are tight.
ƑEnsure the wire nut connections are not rattling against each other or the interior wall of the switch
housing.
ƑAllow a 24-hour “breaking in” period. Most noises associated with a new fan disappear during this time.
ƑIf you are using the Ceiling Fan light kit, ensure the screws securing the glassware are tight. Check that
the light bulbs are also secure.
ƑEnsure the canopy is a short distance from the ceiling. It should not touch the ceiling.
ƑEnsure your outlet box is secure and rubber isolator pads were used between the mounting plate and
outlet box.
The fan wobbles
ƑCheck that all blade and blade arm screws are secure.
ƑMost fan wobble problems are caused when blade levels are unequal. Check this level by selecting a
point on the ceiling above the tip of one of the blades. Measure from a point on the center of the
blade to the point on the ceiling. Rotate the fan until the next blade is positioned for
measurement. Repeat for each blade. Any measurement deviation should be within 1/8". Run the fan for
ten minutes.
ƑUse the enclosed blade balancing kit if the blade wobble is still noticeable.

MOC.YABNOTPMAH
51
.ecnatsissarehtrufrof3130-725-778-1tcatnocesaelP
This page intentionally left blank.

Questions, problems, missing parts? Before returning to the store call
Hampton Bay Customer Service
8 a.m. - 6 p.m., EST, Monday-Friday
1-877-527-0313
HAMPTONBAY.COM
Retain this manual for future use.
X0000000000-A

GRACIAS POR TU COMPRA
Apreciamos la confianza que has depositado en Hampton Bay al comprar este ventilador de techo. Nos esforzamos para continuamente crear
productos de calidad diseñados para tu hogar. Visítanos por Internet para ver nuestra línea completa de productos disponibles para las
necesidades de mejoras de tu hogar. ¡Gracias por elegir Hampton Bay!
Artículo Núm. 458-301, 458-633
Modelo Núm. 26613, 26623
Modelo Núm. 52-WWDIV
Aprobado por UL
GUÍA DE USO Y MANTENIMIENTO
WINDWARD IV - VENTILADOR DE TECHO DE 52 PLG (1,72 M)
¿Preguntas, problemas o piezas faltantes? Antes de regresar a la tienda, llama al
Servicio al Cliente de Hampton Bay
de Lunes a Viernes entre 8 a.m. y 6 p.m., (hora del Este de EE. UU.)
1-877-527-0313
HAMPTONBAY.COM

2
Tabla de Contenido ......................................................2
Información de Seguridad ...........................................2
Garantía..........................................................................3
Pre-Instalación ..............................................................3
Instalación .....................................................................6
Ensamblado ................................................................ 7
Funcionamiento ........................................................ 12
Mantenimiento y Limpieza ...................................... 13
Solución de problemas ............................................ 14
Información de Seguridad
1. Para disminuir el riesgo de descarga eléctrica, asegúrate
de que la electricidad ha sido apagada en el cortacircuitos
o la caja de fusibles antes de comenzar.
2. Todo el cableado debe cumplir con el Código Nacional de
Electricidad ANSI/NFPA 70-1999 y con los códigos locales
de electricidad. La instalación eléctrica debe ser hecha
por un electricista certicado y calicado.
3. La caja eléctrica y estructura de soporte deben montarse
de forma segura y tener capacidad para sostener de
manera conable un mínimo de 35 lb. (16 kg). Usa
solamente cajas eléctricas aprobadas por UL marcadas
como “Para Soporte de Ventilador”.
4. El ventilador debe ir montado con un mínimo de 7 pies
(2 m) de separación entre el borde trasero de las aspas
y el piso.
5. No muevas el interruptor de reversa mientras las aspas del
ventilador estén en movimiento. Debes apagar el ventilador
y detener las aspas antes de invertir la dirección de las
aspas.
6. No coloques objetos en la trayectoria de las aspas.
7. Para evitar lesiones físicas o daños al ventilador y otros
artículos, ten cuidado al limpiar o trabajar cerca del
ventilador.
8. Los diagramas eléctricos son sólo para referencia. Los kits
de luces no empaquetados con el ventilador deben estar
aprobados por UL y marcados como apropiados para ser
usados con el modelo de ventilador a instalar. Los
interruptores deberán estar clasicados por el UL como de
Uso General. Consulta las instrucciones adjuntas a los
juegos de luces e interruptores para obtener información
sobre el montaje adecuado.
9. Después de concluir con las conexiones eléctricas, debes
voltear los conductores empalmados hacia arriba y
empujarlos con cuidado hacia dentro de la caja eléctrica.
Los cables deben estar separados, con el cable a tierra y
el conductor a tierra del equipo hacia uno de los lados de
la caja eléctrica.
10. Todos los tornillos colocados se deben vericar y ajustar
donde sea necesario, antes de la instalación.
ADVERTENCIA: Para reducir el riesgo de lesiones
personales, no dobles los soportes de las aspas
(también llamados “bridas”) durante o después de la
instalación. No coloques objetos en la trayectoria de
las aspas.
ADVERTENCIA: Para reducir el riesgo de incendio
o descarga eléctrica, no utilices este ventilador con
ningún dispositivo de control de velocidad de estado
sólido.
ADVERTENCIA: Para evitar una posible descarga
eléctrica, asegúrate de que la electricidad esté
apagada en la caja de fusibles principal antes de
instalar el cableado. Si crees que no tienes suciente
experiencia o conocimientos en cableado eléctrico,
contrata a un electricista con licencia.
ADVERTENCIA: Los diagramas eléctricos son
sólo para referencia. Cualquier kit de luces opcional
debe estar aprobado por UL y estar marcado como
adecuado para ser usado con este ventilador.
PRECAUCIÓN: Para reducir el riesgo de lesiones
físicas, usa sólo los tornillos incluidos con la caja
eléctrica.
ADVERTENCIA: Para disminuir el riesgo de
incendio o descarga eléctrica este ventilador sólo
debe ser usado con un control de velocidad con el
núm. de pieza Fan28R-240W, fabricado por Chia Wei
Electric Co., LTD.
Tabla de Contenido

HAMPTONBAY.COM
3
Para obtener asistencia, llama al 1-877-527-0313.
El proveedor garantiza de por vida, a partir de la fecha en que el comprador original lo adquiere, que el motor del ventilador no presenta
defectos de fabricación ni de material al momento en que es enviado desde la fábrica. El proveedor también garantiza por un período de dos
años a partir de la fecha de compra por el comprador original, que todas las demás piezas del ventilador, sin incluir ninguna aspa de vidrio o
acrílico, no presentarán ningún defecto de fabricación o de material desde el momento de su salida de la fábrica. Acordamos reparar todos
los defectos del tipo antes mencionado, sin cargo alguno, o a nuestra discreción, reemplazar el producto por un modelo de calidad
comparable o superior si el producto es devuelto. Para obtener un servicio de garantía, debe presentar una copia del recibo como
comprobante de compra. Todos los costos de retiro y reinstalación del producto son su responsabilidad. Los daños a cualquiera de las piezas
como resultado de accidentes, instalación o uso incorrectos, o debidos a la instalación de cualquier accesorio, no están cubiertos bajo esta
garantía. Debido a que las condiciones climáticas pueden variar, esta garantía no cubre ningún cambio en el acabado en bronce, incluyendo
óxido, perforación, corrosión, manchas o descascaramiento. Los acabados en bronce de este tipo tienen una vida útil más prolongada
cuando se protegen de las condiciones climáticas cambiantes. Es normal cierta “oscilación” y no se considerará una falla. Cualquier servicio
técnico conducido por personas no autorizadas anulará la garantía. No hay ninguna otra garantía expresa. Mediante la presente Hampton
Bay se exime de cualquier garantía, incluyendo pero sin limitarse a aquellas de comercialización e idoneidad para un n particular, de
acuerdo a lo contemplado por la ley. La duración de cualquier garantía implícita que no se pueda eximir, está limitada al período de tiempo
especicado en la garantía explícita. Algunos estados no permiten limitaciones en la duración de la garantía implícita, por consiguiente la
limitación anterior puede no aplicarse a su caso. El minorista no será responsable por daños directos, indirectos o especiales que resulten o
deriven del uso o rendimiento del producto excepto en casos en que lo estipule la ley. Algunos estados no permiten la exclusión o limitación
de daños directos o indirectos, por lo que la limitación o exclusión anterior podría no aplicarse a usted. Esta garantía le otorga derechos
legales especícos pero es posible que también tenga otros derechos que varían de un estado a otro. Esta garantía sustituye todas las
garantías anteriores. Los costos de envío de cualquier devolución de productos hecha como parte de una reclamación de garantía deben
ser pagados por el cliente.
Comuníquese con el Equipo de Servicio al Cliente por el 1-877-527-0313 o visita www.hamptonbay.com
Pre-Instalación
ESPECIFICACIONES
Tamaño Velocidad Voltios Peso Neto Peso Bruto Pies Cúb
52”
Baja
120 20,2 lb
(9,2 kg)
23,1 lb
(10,5 kg) 1.7’
Media
Alta
12
30
57
204
143
106
2448
4289
6057
NOTA: Estas medidas son aproximadas. No incluyen ni el
amperaje ni el vataje consumido por el kit de luces.
HERRAMIENTAS NECESARIAS
Destornillador
Phillips
Destornillador
plano
Llave
ajustable
Cinta de
electricista
Cortacables
Escalera
Garantía
FLUJO DE
AIRE PIES
CÚB. X MIN.
CONSUMO
DE ENERGÍA
(SIN LAS LUCES)
EN VATIOS
EFICIENCIA DE FLUJO
DE AIRE (MIENTRAS
MÁS ALTA MEJOR) PIES
CÚB. X MIN/VATIOS)

4
HERRAJES INCLUIDOS
NOTA: No se muestra el tamaño real de los herrajes.
Pieza Descripción Cantidad Pieza Descripción Cantidad
AA Tornillo de montaje de aspas 16
1
1
BB Tuerca para conectar cable
CC Pasador de soporte
DD Pasador de cierre
EE Kit de compensación de aspas
Herrajes para montaje
“Cerca del Techo” (junta de goma) 1
1
FF
AA BB CC DD EE
FF
Pre-Instalación (continuación)
3