Hand Held Products Quick Check PC600 User manual

Quick Check® PC600
Bar Code Verifier
User’s Guide

Disclaimer
Hand Held Products, Inc. (“Hand Held Products”) reserves the right to make
changes in specifications and other information contained in this document
without prior notice, and the reader should in all cases consult Hand Held
Products to determine whether any such changes have been made. The
information in this publication does not represent a commitment on the part of
Hand Held Products.
Hand Held Products shall not be liable for technical or editorial errors or
omissions contained herein; nor for incidental or consequential damages
resulting from the furnishing, performance, or use of this material.
This document contains proprietary information that is protected by copyright. All
rights are reserved. No part of this document may be photocopied, reproduced,
or translated into another language without the prior written consent of Hand
Held Products.
©2001-2007 Hand Held Products, Inc. All rights reserved.
Web Address: www.handheld.com

Statement of Agency Compliance
This device complies with part 15 of the FCC Rules. Operation is subject to the
following two conditions: (1) this device may not cause harmful interference, and
(2) this device must accept any interference received, including interference that
may cause undesired operation.
FCC Class A Compliance Statement
This equipment has been tested and found to comply with the limits for a Class A
digital device, pursuant to part 15 of the FCC Rules. These limits are designed
to provide reasonable protection against harmful interference when the
equipment is operated in a commercial environment. This equipment generates,
uses, and can radiate radio frequency energy and, if not installed and used in
accordance with the instruction manual, may cause harmful interference to radio
communications. Operation of this equipment in a residential area is likely to
cause harmful interference, in which case the user will be required to correct the
interference at his own expense.
Caution: Any changes or modifications made to this equipment not
expressly approved by Hand Held Products, Inc. may void the FCC
authorization to operate this equipment.
Note: To maintain compliance with FCC Rules and Regulations, cables
connected to this device must be shielded cables, in which the cable shield
wire(s) have been grounded (tied) to the connector shell.
Canadian Notice
This equipment does not exceed the Class A limits for radio noise emissions as
described in the Radio Interference Regulations of the Canadian Department of
Communications. (ICES-003)
Le present appareil numerique n'emet pas de bruits radioelectriques depassant
les limites applicables aux appareils numeriques de la classe A prescrites dans
le Reglement sur le brouillage radioelectrique edicte par le ministere des
Communications du Canada. (ICES-003)

The CE mark on the product indicates that the system has been tested
to and conforms with the provisions noted within the 89/336/EEC
Electromagnetic Compatibility Directive and the 73/23/EEC Low Voltage
Directive.
For further information please contact:
Hand Held Products, Inc.
Nijverheidsweg 9
5627 BT Eindhoven
The Netherlands
Hand Held Products shall not be liable for use of our product with equipment (i.e.,
power supplies, personal computers, etc.) that is not CE marked and does not
comply with the Low Voltage Directive.
Limited Warranty
Hand Held Products, Inc., ("Hand Held Products") warrants its products to be
free from defects in materials and workmanship and to conform to Hand Held
Products' published specifications applicable to the products purchased at the
time of shipment. This warranty does not cover any Hand Held Products product
which is (i) improperly installed or used; (ii) damaged by accident or negligence,
including failure to follow the proper maintenance, service, and cleaning
schedule; or (iii) damaged as a result of (A) modification or alteration by the
purchaser or other party, (B) excessive voltage or current supplied to or drawn
from the interface connections, (C) static electricity or electro-static discharge,
(D) operation under conditions beyond the specified operating parameters, or (E)
repair or service of the product by anyone other than Hand Held Products or its
authorized representatives.
This warranty shall extend from the time of shipment for the duration published
by Hand Held Products for the product at the time of purchase ("Warranty
Period"). Any defective product must be returned (at purchaser’s expense)
during the Warranty Period to Hand Held Products' factory or authorized service
center for inspection. No product will be accepted by Hand Held Products
without a Return Materials Authorization, which may be obtained by contacting
Hand Held Products. In the event that the product is returned to Hand Held
Products or its authorized service center within the Warranty Period and Hand
Held Products determines to its satisfaction that the product is defective due to
defects in materials or workmanship, Hand Held Products, at its sole option, will
either repair or replace the product without charge, except for return shipping to
Hand Held Products.
3

EXCEPT AS MAY BE OTHERWISE PROVIDED BY APPLICABLE LAW, THE
FOREGOING WARRANTY IS IN LIEU OF ALL OTHER COVENANTS OR
WARRANTIES, EITHER EXPRESSED OR IMPLIED, ORAL OR WRITTEN,
INCLUDING, WITHOUT LIMITATION, ANY IMPLIED WARRANTIES OF
MERCHANTABILITY OR FITNESS FOR A PARTICULAR PURPOSE.
HAND HELD PRODUCTS’ RESPONSIBILITY AND PURCHASER’S
EXCLUSIVE REMEDY UNDER THIS WARRANTY IS LIMITED TO THE REPAIR
OR REPLACEMENT OF THE DEFECTIVE PRODUCT. IN NO EVENT SHALL
HAND HELD PRODUCTS BE LIABLE FOR INDIRECT, INCIDENTAL, OR
CONSEQUENTIAL DAMAGES, AND, IN NO EVENT, SHALL ANY LIABILITY
OF HAND HELD PRODUCTS ARISING IN CONNECTION WITH ANY
PRODUCT SOLD HEREUNDER (WHETHER SUCH LIABILITY ARISES FROM
A CLAIM BASED ON CONTRACT, WARRANTY, TORT, OR OTHERWISE)
EXCEED THE ACTUAL AMOUNT PAID TO HAND HELD PRODUCTS FOR
THE PRODUCT. THESE LIMITATIONS ON LIABILITY SHALL REMAIN IN
FULL FORCE AND EFFECT EVEN WHEN HAND HELD PRODUCTS MAY
HAVE BEEN ADVISED OF THE POSSIBILITY OF SUCH INJURIES, LOSSES,
OR DAMAGES. SOME STATES, PROVINCES, OR COUNTRIES DO NOT
ALLOW THE EXCLUSION OR LIMITATIONS OF INCIDENTAL OR
CONSEQUENTIAL DAMAGES, SO THE ABOVE LIMITATION OR EXCLUSION
MAY NOT APPLY TO YOU.
All provisions of this Limited Warranty are separate and severable, which means
that if any provision is held invalid and unenforceable, such determination shall
not affect the validity of enforceability of the other provisions hereof. Use of any
peripherals not manufactured/sold by Hand Held Products voids the warranty.
This includes but is not limited to: cables, power supplies, cradles, and docking
stations. Hand Held Products, Inc. extends these warranties only to the first end-
users of the products. These warranties are nontransferable.
The limited duration of the warranty for the Quick Check PC600 Bar Code
Verifier is for two (2) years.

5

i
Table of Contents
Introduction.......................................................................................1
Getting Started with Quick Check®PC.............................................2
Unpacking / What's Included............................................................................. 2
Quick Check®PC Quick Start...........................................................3
Quick Check®PC Installation and Setup.........................................6
Quick Check®PC Features.............................................................11
Summary Grade Information........................................................................... 13
General Scan Results....................................................................................... 14
Reflectance Measures...................................................................................... 15
ISO/IEC Scan Grade........................................................................................ 15
Format Parameters.......................................................................................... 16
Dimensional Parameters ................................................................................. 16
Additional Data ............................................................................................... 17
Status Bar ........................................................................................................ 18
Additional Features......................................................................................... 18
Configuration and Settings.............................................................................. 19
Verification Parameters................................................................................... 19
Scan Direction .................................................................................19
Using Quick Check®PC..................................................................20
Wand/Mouse Aperture Selection...................................................................... 21
View Individual Scan Results........................................................................... 23
View Scan Reflectance Profile......................................................................... 24
Bar/Space Analysis.......................................................................................... 24
Calculate “X”.................................................................................................. 24
Notes................................................................................................................ 25
Reflectometer................................................................................................... 25
Print Report..................................................................................................... 26
Getting Help .................................................................................................... 26
Context Sensitive Help..................................................................................... 27
Understanding Print Quality Results..............................................27
Common Corrective Actions ...........................................................32
Error messages ................................................................................34

Frequently Asked Questions ...........................................................35
Glossary of Terms............................................................................39
Additional Sources of Information.................................................56
Electrical Specifications..................................................................57
Appendix A Messages......................................................................59
Additional Data Messages:.............................................................................. 59
Error Messages: .............................................................................................. 59
Appendix B Notes for Windows .....................................................60
Additional Notes For Windows:....................................................................... 60
Technical Assistance .......................................................................60
ii

Introduction
Hand Held Products is pleased to supply you with the Quick Check®PC bar code
verification system. The instrument and software offer an easy-to-use and
powerful combination that provides both pass/fail testing and full traditional and
ISO/IEC verification with significant detail.
This manual contains information on Quick Check®PC instrument and software.
It describes all the features and functions of the software and provides additional
information about bar code symbol quality and the ANSI X3.182 / CEN EN1635 /
ISO/IEC 15416 method of symbol verification.
This manual is organized into the following sections:
•System Requirements
•Windows®98, 2000 and NT operating system
•PC (or compatible) with 486 or better processor
•4 Megabytes of RAM
•3 Megabytes available on hard drive
•Available COM Port (COM 1-4)
•Microsoft Compatible Mouse
•Getting Started
•Quick Start Guide
•Quick Check®PC Installation and Setup
•Quick Check®PC Features
•Using Quick Check®PC
•Understanding Print Quality Results
•Common Corrective Actions
•Error Messages
•FAQs - Bar Code Basics
•Glossary of Terms
•Additional Sources of Information
•Appendix A: Additional Data Messages
•Appendix B: Setting up Windows Communications
•Technical Support
1

Getting Started with Quick Check®PC
Unpacking / What's Included
When you first receive your Quick Check®PC, inspect the packaging for any
signs of shipping damage. If there is evidence of damage, please keep ALL
packing materials and contact the delivery carrier as soon as possible for claim
procedure.
Unpack the Quick Check®PC carefully and confirm that you have the following
items:
•The Quick Check®PC Interface Module
•9-pin/RJ-12 serial cable
•Hand Held Products Quick Check®Mouse Wand or Pen Wand
•AC charger/power supply
•4 “AA” Rechargeable NiCad batteries
•Quick Check®PC software (CD-ROM)
•User’s Guide
•Packaged with the Manual
Ruler for measuring symbol length
Gauge ruler (showing common sizes of bar code symbols)
•Reference Symbols (6 sheets)
•Reflectance Calibration Page (QCRFPG)
If you do not have all these items, contact your sales representative.
2

Quick Check®PC Quick Start
If you've used a Quick Check®or other verifier before, you'll probably skip reading
the manual and just click different parts of the control panel until you figure things
out. That's okay. Quick Check®PC software is designed to allow an intuitive
interface for those familiar with the verification process and Windows-based
software. If you get stuck, you can try the on-line help or read the following
sections.
 Be sure to review the README.TXT file included with the installation. This
file contains a complete list of Quick Check®PC files that are installed on
your computer along with change or update notices.
The following QuickStart provides basic information for those familiar with
Windows, hardware and software setup, and verification. If you are unsure about
any part of the procedure, see the corresponding section under Installation.
In the following sections, there are several graphical symbols used to indicate the
type of activity referred to in the text. These are:
 Problems or cautions
 Things to remember
 Notes
 PC (hardware) configuration
 Windows setup procedures or tips
CD operations
 Keyboard shortcut or commands
 Mouse operation
 Right-click mouse operation
 One important operational note: right-clicking on areas of the screen that
display variable parameters will bring up a menu allowing you to review and/or
change that parameter. The cursor changes to a “screwdriver” on any area
where right-clicking will call out a pop-up menu.
There are five features on the interface module: 9-pin wand connector (front), RJ-
45 connector (back), power adapter connector (back), and a power button and
LED indicator on the face of the unit.
•Power button:
•Press to turn unit on.
3

•Press to turn unit off.
•LED Status indicator:
•The LED indicator is a 3-color indicator.
•Green indicates that the interface module is functioning properly and
has established connection with the Quick Check®PC software.
•Amber (yellow) indicates an error during communications.
•Red indicates that the interface module cannot establish a
connection to the Quick Check®PC software on the computer or that
no wand is connected.
1. Insert the 4 AA NiCad batteries into the back (base) of the interface module.
You must insert the batteries before connecting the AC power supply.
•Make sure the batteries are installed correctly. Incorrect installation
could damage the device.
•Use only NiCad rechargeable batteries. Do not use alkaline or other
types of batteries. Do not mix old and new batteries.
 FAILURE TO FOLLOW THESE PROCEDURES MAY RESULT IN
EXPLOSION OF BATTERIES, DAMAGE TO THE EQUIPMENT, AND/OR
PERSONAL INJURY.
2. Select the cable that has an RJ-45 plug on one end and the proper serial
connection for your communications port on the other.
•Plug the “phone jack” into the Quick Check®interface module.
•Connect the serial connector to your communications port.
•If your serial port has a 25 pin connector, a 9 to 25 pin adapter should
be used.
3. Plug the power adapter into a working outlet and into the interface module.
4. Connect the Pen Wand or Mouse Wand to the interface module
•If you have more than one Wand, select the one that most closely
matches your application need. Refer to page 22
 Note: Although there should be no problem installing Quick Check®PC
software with virus-checking software, you may wish to disable any anti virus
software (BIOS and programs) running on your system.
 To ensure sufficient systems resources are available, exit all other programs
before installing or running Quick Check®PC Software.
Insert the Quick Check®PC CD ROM into your PC.
 Windows: From the Windows Taskbar, select “Start”, “Run”.
4

Type D:\setup and click “OK”. (Note, if your CD is not drive “D” then you should
type that letter instead of “D”.)
The Install program will install the Quick Check®PC software onto your hard
drive. You will have the option of selecting an alternate location or
folder/directory name for installation. If you choose this option, be sure to make
a note of the location you selected for future reference.
Once installation is complete, remove the Quick Check®CD ROM and re-
enable any virus checkers.
1. Turn on the interface module (press the Power button).
2. Start the Quick Check®PC software.
 Double-click the Quick Check®PC icon in the Quick Check®PC window to
start the Quick Check®PC software. Or
•In Windows, start Windows Explorer or click on My Computer and locate
the QCPC32 folder. The default location is C:\Program
Files\HHP\QCPC. Double-click the folder to open it then double-click
QCPC32.EXE.
3. Select the Com port.
•Click the “Configure” icon or select Settings, Configure from the
command menu. Select the proper Com port, click “OK” to close the
menu. Quick Check®PC default is “No Com Port” on installation.
If you have not already done so, turn on the interface unit and start the Quick
Check®PC software.
•Scan the calibration page (use with the Mouse Wand) to begin the
calibration process. Ten consecutive scans are required for calibration.
An audio tone indicates a successful scan. Screen prompts will advise
you of your progress. Note, if scans are too variable, you will have to
start over.
•When the calibration is completed, the calibration screen will disappear.
1. Select symbologies, options, quality measures, and other parameters for a
specific verification procedure.
•Position the cursor over each variable parameter. (Note: the cursor
changes to a “screwdriver” over any area that has user-definable
parameters -- see the appropriate section under “Installation and Setup”
for details.)
 Right-click to bring up a pop-up menu to set parameters.
•Select the desired parameters.
•Click “OK” when done with each parameter (or “Cancel” if you've
brought up the menu by mistake).
5

 Note: your settings will automatically be saved when you exit the Quick
Check®PC program.
 Note: For information on default settings, see the “Select Verification
Parameters” in the following section.
2. You are now ready to verify symbols.
Quick Check®PC software provides many useful functions not available with
conventional verifiers. Among these features are:
•Set number of scans (1-50)
•Store symbol results
•Review symbol results
•Customizable scan or symbol result reports
•Print individual scan profiles
•Calculate X dimension
•View individual scan profile
•View element width chart
•Obtain reflectometer readings
•Attach a note to symbol results
 Note: For additional information and default settings, please refer to the
appropriate sections under “Installation and Setup.”
Quick Check®PC Installation and Setup
The following sections provide complete instructions for installing and setting up
your Quick Check®PC hardware and software.
In the following sections, there are several graphical symbols used to indicate the
type of activity that the text refers to. These are:
 Problems or cautions
 Things to remember
 Notes
 PC (hardware) configuration
 Windows setup procedures or tips
CD ROM operations
 Mouse operation
 Right-click mouse operation
6

 Keyboard shortcut or operation
 IF YOU DO NOT HAVE AN AVAILABLE COM PORT: STOP!
For computers with USB and parallel ports (no serial ports) you can use a USB to
serial converter (USB on PC end, male serial on end that connects to the
QCDB09F female 9-pin serial port or a PC Card (PCMCIA) with a male serial
adapter.
You may not connect the Quick Check®PC device to your mouse serial port
unless you have a Windows®keyboard with the additional Windows function
keys. A mouse is required for optimal Quick Check®PC software operation.
•Do not connect the Quick Check®PC interface module to COM 3 unless
the port uses a different interrupt (IRQ) than COM 1. COM 1 and COM
3 typically share the same interrupts and erratic performance of both the
mouse and the Quick Check®PC software will result if there is an IRQ
conflict.
 Note: You can install the Quick Check®PC software on a PC that does not
have an available COM port if you do not intend to connect the interface unit.
Installing the Quick Check®PC software allows supervisory or quality personnel
to review results (files) at a location other than where symbols are verified. If you
choose this option, an advisory message in the lower left corner of the Quick
Check®PC screen will indicate “No Port Selected.” This is the default setting for
the software.
 IF YOU DO HAVE AN AVAILABLE COM PORT:
Insert the 4 AA NiCad batteries into the back (base) of the interface module. You
must insert the batteries before connecting the AC charger.
•Make sure the batteries are installed correctly. Incorrect installation
could damage the device.
•Use only NiCad rechargeable batteries. Do not use alkaline or
other types of batteries. Do not mix old and new batteries.
 FAILURE TO FOLLOW THESE PROCEDURES MAY RESULT IN
EXPLOSION OF BATTERIES, DAMAGE TO THE EQUIPMENT, AND/OR
PERSONAL INJURY.
2. Select the cable that has an RJ-45 plug on one end and the proper serial
connection for your communications port on the other.
•Plug the “phone jack” into the Quick Check®interface module.
•Connect the serial connector to your communications port.
•If your serial port has a 25 pin connector, a 9 to 25 pin adapter should
be used.
3. Plug the power adapter into a working outlet and into the interface module.
4. Connect the Pen Wand or Mouse Wand to the interface module
7

•If you have more than one Wand or Mouse Wand, select the one that
most closely matches the size of the symbols you will be verifying. (See
Help Topics or “Choose the Right Wand” under the “Using Quick Check®
PC” for Aperture Size recommendations or refer to page 22.)
 Disable virus checkers (BIOS and software)
 NOTE: Although there should be no problem installing Quick Check®PC
software with virus-checking software, you may wish to disable any anti virus
software (BIOS and programs) running on your system as a precaution.
 To ensure sufficient systems resources are available, exit all other programs
before installing or running Quick Check®PC Software.
Insert the Quick Check®PC CD ROM into your PC.
 Windows: From the Windows Taskbar, select “Start”, “Run”
 Type D:\setup and click “OK”. (Note, if your CD is not drive “D” then you
should type that letter instead of “D”.)
 In Windows you can also use the “Add/Remove Programs” control panel.
From the Taskbar select: “Start”, “Settings”, “Control Panel”, “Add/Remove
Programs”.
The Install program will install the Quick Check®PC software onto your hard
drive. You will have the option of selecting an alternate location or
folder/directory name for installation. If you choose this option, be sure to make
a note of the location you selected for future reference.
 Once installation is complete, remove the Quick Check®CD ROM and re-
enable any virus checkers.
1. Turn on the interface module (press the Power button).
2. Start the Quick Check®PC software.
 Double-click the Quick Check®PC icon in the QCPC600 window to start the
Quick Check®PC software. Or
•In Windows, start Windows Explorer or click on My Computer and locate
the QCPC32 folder. The default location is C:\Program Files\ Hand
Held Products\QCPC. Double click the folder to open it then double-
click QCPC32.EXE.
3. Select the Com port.
•Click the “Configure” icon or select Settings, Configure from the
command menu. Select the proper Com port, click “OK” to close the
menu. Quick Check®PC default is “No Com Port” on installation.
In order to verify symbols, the Quick Check®PC needs a baseline measurement.
The Setup Symbol provided with your Quick Check®PC is carefully produced
8

with known reflectance and dimensional performance characteristics. Scanning
this symbol provides the Quick Check®PC with the proper reference.
If you have not already done so, turn on the interface unit and start the Quick
Check®PC software.
•Scan the calibration page (for the Mouse Wand) inside the manual to
begin the calibration process.
•Ten consecutive scans are required for calibration. An audio tone
indicates a successful scan. Screen prompts will advise you of your
progress. Note, if scans are too variable, you will have to start over.
•When the calibration is completed, the calibration screen will disappear.
 Note: You will need to calibrate the input device every time it detects that
a wand has been disconnected. This is true even if the same wand is then
reconnected. Also, if you configure the software to accept scans in only one
direction, you will be able to scan in only that direction for wand calibration.
 Note: Make sure you use only the original calibration page that were
supplied with your Quick Check®PC. This calibration page is produced under
strict quality procedures and is NIST-traceable.
Failure to use the proper calibration page may result in improper operation of
your Quick Check®PC and will likely yield unreliable results.
Before you can effectively verify symbols, you must choose the symbologies,
quality measures and acceptable levels you need. If you are uncertain about the
meaning of any of the measures and parameters, please see the section
“Verification Measures.”
Select symbologies, options, quality measures, and other parameters for a
specific verification procedure.
•Position the cursor over each variable parameter.
 Note: The cursor changes to a “screwdriver” over any area that has user-
definable parameters -- see “Settings and Parameters” for details.)
 Right-click to bring up a pop-up menu to set parameters.
•Select the desired parameters.
•Click “OK” when done with each parameter (or “Cancel” if you've
brought up the menu by mistake).
 Note: Your settings will automatically be saved when you exit the Quick
Check®PC program.
Status Light on the Quick Check®PC interface module remains red.
 The Quick Check®PC interface module is unable to connect to the serial
port.
•Check the cable connections.
9

•Also see below for Com port problems
•Check to see if any programs are running that seize control of the
communications port interrupts (such as “autoanswer” fax programs).
Close any conflicting applications.
 “No Connection!” appears on the Quick Check®PC status bar.
•Check to make sure the interface module is turned on (and plugged in
to a working outlet or has fully-charged batteries).
•Check the connections at the interface module and the communications
port.
•Check to make sure the scanner is properly attached.
•Check communications port setup.
•Check the software configuration to ensure that the port setting is the
same as the one to which you have connected the Quick Check®PC
Interface Module.
 “No Port Selected” appears on the Quick Check®PC status bar.
•You have not selected a communications port (see “Software
Configuration” above).
 Mouse cursor freezes or disappears after starting Quick Check®PC
program.
•You have assigned the same IRQ to the Quick Check®PC serial port
that's used by your mouse. Assign a different setting (IRQ) to the Quick
Check®PC port. (See: Appendix B for tips.)
 Calibration error message (input device configuration)
•Wand requires adjustment, contact your sales representative.
 Software does not install.
•Check to make sure that you typed D:\setup.exe at the “Run” prompt.
(Typos are a major cause of software installation failure.)
•Ensure that you have enough hard disk space to install the program
(approximately 3 megs are required).
•Remove the CD ROM, restart the computer and try again.
•Check that the CD drive is operational.
•If the software still does not install, please call your sales representative.
10

Quick Check®PC Features
The Quick Check®PC screen is divided into a number of different areas).
Title Line
•Program name; name of open Quick Check®PC saved file (if any) in
brackets.
Menu Line
•Provides access to the Quick Check®PC's configuration and file
management functions.
Toolbar Icons
•Quick and easy access to the power of the Quick Check®PC with a
single click of the mouse.
Main Screen
•Summary Grade Information
•ISO/IEC scan results, number of scans, and a running ISO/IEC
symbol quality result.
•General Scan Results
•Decoded symbol data
•Symbology decoded
•Scan direction
•Speed variance (if enabled)
•Reflectance Results
•Traditional and ISO/IEC reflectance data
•Scan Grade
•ISO/IEC Scan Grade
•Format Parameters/Results
•Check digit (optional, if enabled)
•Message length
•Dimensional Parameters
•Decodability
•Intercharacter Gap (if applicable)
•Wide-to-Narrow Ratio (if applicable)
•Average Bar Error
•Bar growth/shrinkage “LED” indicators
•Status Bar
•Advisory and prompt messages.
•Scanner type/connection status
11

•Scan status (# of #)
•Current COM port selection
•Status “LED” red/green/off indicator in lower right to indicate whether
the software is ready to accept scans or not.
•“Battery Low” indicator in lower right hand corner (appears only
during battery low conditions).
Menu items are shown below.
•For menu access, Quick Check®PC software recognizes either mouse
selection or the key sequence of the underlined letters following the [Alt]
key (e.g., [Alt],F,O is the same as clicking on File, Open).
Toolbar icons provide quick way to access the powerful features of the Quick
Check®PC software. Icons are described below. Note: icons are “grayed out” if
the option is not available at the time.
Open File
Opens previously saved symbol summary containing one or more individual
scans.
Save File
•Save the current symbol summary (including all individual scans).
Reports
•Select printer, produce reports
Configure
•Select Communications Port
•Select Report Details
•Select Report Types
Set Scan Count
•Select from 1 to 50 individual scans to produce the final grade (ISO/IEC
method).
Previous Scan
•View the results of the one previous scan (of a series).
12