Hanna Instruments HI 4114 User manual

1
Instruction Manual
SENSOR HANDLE
HI
4000-50
HI 4114
POTASSIUM
COMBINATION
HI 4014HI 4014
HI 4014HI 4014
HI 4014
HI 4114HI 4114
HI 4114HI 4114
HI 4114
Potassium Ion
Selective Electrode
Half-cell
Combination

23
III.III.
III.III.
III. Theory of Operation:Theory of Operation:
Theory of Operation:Theory of Operation:
Theory of Operation:
The HI 4014 and HI 4114 potassium electrodes are poten-
tiometric devices used for the rapid determination of free
potassium ions in water, soft drinks, wine, and soils. The
electrode functions as a sensor or ionic conductor. HI 4014
requires a separate reference electrode to complete its elec-
trolytic circuit. HI 4114 is a combination electrode with a
reference electrode incorporated in its design. The PVC mem-
brane used on the sensor is impregnated with the organic
ion exchanger valinomycin. This carrier ionophore encloses
the ion like a cage. The outside of the ionophore molecule
is uncharged and it can freely diffuse through the lipid
layers of the membrane producing a charge imbalance
between the test solution and internal cell of the sensor.
This produces a voltage that changes in response to the
sample’s ion activity. When the ionic strength of the sample
is fixed, the voltage is proportional to the concentration of
potassium ions in solution. The sensor follows the Nernst
Equation:
E = Ea + 2.3 RT/nF log A ion
E = observed potential
Ea= Reference and fixed internal voltages
R = gas constant (8.314 J/K Mol)
n= Charge on ion (equivalents/mol) (1+)
A ion = ion activity in sample
T = absolute temperature in K
F = Faraday constant (9.648 x 104 C/equivalent)
HI 4014 PHI 4014 P
HI 4014 PHI 4014 P
HI 4014 Potassium half-cellotassium half-cell
otassium half-cellotassium half-cell
otassium half-cell
HI 4114 PHI 4114 P
HI 4114 PHI 4114 P
HI 4114 Potassium combination electrodeotassium combination electrode
otassium combination electrodeotassium combination electrode
otassium combination electrode
I.I.
I.I.
I. IntroductionIntroduction
IntroductionIntroduction
Introduction
The Hanna HI 4014 and HI4114 are ion selective elec-
trodes designed for the measurement of potassium ions in
aqueous solutions. They utilize a replaceable sensing mod-
ule that contains an organic polymer membrane that is
sensitive to potassium. HI 4014 is a half-cell electrode that
requires a separate reference.
HI 4114 is a combination ion selective electrode.
IIII
IIII
II. SpecificationsSpecifications
SpecificationsSpecifications
Specifications
Type: PVC membrane with
organic ion exchanger
Ion measured: Potassium (K+)
Measurement range: 1M to 1X 10-6M
39100 to 0.039ppm
Operating Temperature: 0-40°C
Operating pH: 1.5 to 12.0 pH
Dimensions: 12 mm (OD)(0.47”) X
120 mm (4.72”)
(insertion)
Connection: BNC
Interference:
Organic solvents andcationic detergents must be absent.
Ratio of interfering ion to K+must be below
10 for NH4
+
300 for Li+
2000 for Na+
2000 for Ca2+

45
V.V.
V.V.
V. Equipment Required:Equipment Required:
Equipment Required:Equipment Required:
Equipment Required:
•HI 4014 requires the Hanna HI 5315 Double Junction
reference electrode with HI 7076 as external electro-
lyte.
•Hanna HI 4222 pH/ISE/mV meter or other suitable
ion or pH/mV meter. (Note: log/linear graph paper is
useful if an ISE (ion) meter is not available).
•Hanna HI 180 magnetic stirrer or equivalent with
magnetic stirring bars (Note: Isolate beakers from stir-
rer motor heat by placing insulating material such as
foam or cork between them).
•Hanna HI 76404 electrode holder or equivalent.
•Plastic beakers ( HI 740036P) or other suitable mea-
surement vessel.
VI.VI.
VI.VI.
VI. Solutions Required for PSolutions Required for P
Solutions Required for PSolutions Required for P
Solutions Required for Potassium Measure-otassium Measure-
otassium Measure-otassium Measure-
otassium Measure-
mentsments
mentsments
ments
0.1 M potassium standard, 500 mL HI 4014-01HI 4014-01
HI 4014-01HI 4014-01
HI 4014-01
Ionic Strength Adjuster, 500 mL HI 4014-00HI 4014-00
HI 4014-00HI 4014-00
HI 4014-00
Using volumetric pipettes and glassware make dilutions to
bracket the concentration of the samples. Standards with
concentrations <10-3 M should be prepared daily.
Store standards in plastic bottles. Add 2 mL of Hanna ISA
HI 4014-00 to 100 mL sample or standard.
IV.IV.
IV.IV.
IV. Design elements of the HI 4014 and HI 4114Design elements of the HI 4014 and HI 4114
Design elements of the HI 4014 and HI 4114Design elements of the HI 4014 and HI 4114
Design elements of the HI 4014 and HI 4114
electrodeselectrodes
electrodeselectrodes
electrodes
SENSORHANDLE
HI
4000-50
Cap
Sensing
module
Sensor
Handle
O-Ring
Upper Cap
Spring
O-Ring
Ceramic Junction
on Inner Stem
Fill Hole
O-Ring and
Plug
Sensing Module
Outer Sleeve
Upper
Threads
Liquid junction

67
•Due to shipping or storage the internal solution inside
the sensing modules may have developed an air
pocket near the membrane. Gently shaking the sensor
down (like the old style mercury thermometers) will
place the internal solution next to the membrane.
•Presoaking the potassium sensor in a 10-2 M standard
for at least half-hour before calibration will help to
optimize the sensor response.
•Calibration standards and sample solutions should
have the same ionic strength. ISA should be added to
both samples and standards in the same ratios.
•Calibration standards and sample solutions should
be at the same temperature.
•Thermally insulate solution vessel from magnetic stir-
rer.
•Calibration standards and sample solutions should
be stirred at the same rate using identically sized TFE
coated stir bars.
•Rinse electrode pair with distilled or deionized water
between samples and dab dry with lab wipe or other
soft disposable absorbent toweling. Do not rub mem-
branes.
•Check for gas bubbles that may form near the sensing
surface (due to temperature changes). Tap off gently.
•Avoid large changes in temperature (thermal shock)
as it may damage the sensor.
Additional HI 4114 Guidelines
•Remove the protective plastic wrap that covers the
ceramic junction before assembling sensor for the first
time.
•Add reference fill solution HI 7076 to bottom of fill
hole or empty and refill solution daily before using.
•During measurement always operate electrode with
the fill hole open.
•During normal use, fill solution will slowly drain out
of the tapered cone junction at the lower portion of the
electrode. Excessive loss (>4 cm drop within 24 hours)
is not normal. If this occurs verify cap is tightened and
the interface between the internal cone and outer
body is free of debris.
•Add filling solution daily to maintain a good head
pressure. For optimum response, this level should be
maintained and not be allowed to drop more than 2
-3 cm (1-inch) below fill hole.
•Do not use an electrode if crystallized salts are visible
inside the electrode. Drain electrode, disassemble and
rinse internal body with deionized water. Reassemble
and refill with fresh fill solution.
•If an erratic measurement occurs, check to see if for-
eign matter is seen trapped near the internal cone.
Drain by depressing the electrode cap then refill with
fresh fill solution.
VIII.VIII.
VIII.VIII.
VIII.Electrode PreparationElectrode Preparation
Electrode PreparationElectrode Preparation
Electrode Preparation
HI 4014
The Hanna HI 4014 is a 2 piece design comprised of a
sensor handle (HI 4050) and a sensing module (HI 4014-
51).
1) Remove sensing module from shipping vial. Do not
touch the sensing membrane with the “H”hole pat-
tern on it.
2) Screw the module into the sensor handle finger tight.
Do not over tighten.
VIIVII
VIIVII
VII. General GuidelinesGeneral Guidelines
General GuidelinesGeneral Guidelines
General Guidelines
•Ensure the o-ring is installed on modules before screw-
ing into the sensor handle or inner stem.
O-Ring

89
4. Rinse inner stem with deionized water making certain
to wet o-ring found on the inner stem.
5. Reassemble electrode by gently pushing the inner
assembly into the outer body, sliding spring down
cable, and screwing cap into place.
6. Remove fill hole cover and o-ring on fill hole spout.
Using the dropper pipette provided, add a few drops
HI 7076 fill solution to the electrode, wetting the o-
ring and rinsing out the fill solution chamber.
Deionized
Water
Remove
Parafilm
3) Holding the assembled electrode at the cable end,
shake the sensor to ensure internal fill solution that
may have separated during shipping is in contact
with inner membrane surface.
4) Prepare reference electrode by filling outer electrolyte
reservoir with fill solution HI 7076.
5) Place sensor (and reference) electrodes into electrode
holder and connect cable connectors to meter.
6) Soak the potassium membrane in a potassium con-
taining standard for a hour before calibration.
HI 4114
The Hanna HI 4114 is shipped dissembled.
1. Unwrap Parafilm®seal found over ceramic junction
on inner stem and discard. This is only used for ship-
ping and long term storage.
2. Open the glass vial (HI 4114-51) and remove the
potassium sensing cone. Do not touch the sensing
membrane with the “H”hole pattern on it.
3. Ensure o-ring is installed on module before screwing
the cone into the inner stem finger tight. Do not over
tighten.
SENSORHANDLE
HI
4000-50
®

10 11
9. Tighten the electrode cap onto the body and fill elec-
trode body until fill solution volume is just below fill
hole.
10. Position electrode in a Hanna HI 76404 electrode
holder (or equivalent) and connect BNC connector to
meter.
IX.IX.
IX.IX.
IX. Quick Check of Electrode SlopeQuick Check of Electrode Slope
Quick Check of Electrode SlopeQuick Check of Electrode Slope
Quick Check of Electrode Slope
•Connect electrode(s) to pH/mV/ISE meter.
•Place meter in mV mode.
•Place 100 mL of deionized water into a beaker with
stir bar.
•Place reference and measuring half-cell or combina-
tion electrode into prepared sample.
•Add 1 mL of a standard to beaker. Record the mV
value when stable.
•Add an additional 10 mL of standard to the solution.
Record the mV when reading has stabilized. This
7.
upper cap with your thumb. This permits the fill solu-
tion to drain out of the body.
8.
HI 4114
POTASSIUM
COMBINATION
value should be more than the previous value noted
(more positive).
•Determine the difference between the two mV values.
An acceptable value for this slope is
56 ± 4 mV at typical room temperatures
(20-25°C).
X.X.
X.X.
X. Corrective ActionCorrective Action
Corrective ActionCorrective Action
Corrective Action
•Verify module has been screwed into sensor handle or
inner stem.
•Verify seal has been removed from ceramic junction
(HI 4114) or HI 5315 reference electrode.
•Verify electrodes are connected properly to meter and
meter is powered.
•Verify dilute standards are freshly made and stored.
Remake solutions if appropriate. Store in plastic
bottles.
•If the reading is unstable, shake sensor down (see
Section VII).
•If the sensor slope just misses the suggested slope
window, soaking the sensor in a standard may solve
the problem.
•If the membrane is damaged, the response becomes
extremely sluggish, or the slope of the electrode has
decreased significantly, and procedures above have
not helped, the modules should be replaced.
Module replacement for HI 4014
1. Dry off module and sensor handle.
2. Unscrew sensing module and replace with a new one.
(HI 4014-51).
3. Soak new assembled module in potassium solution
to condition it before calibration.
Module replacement for HI 4114
1. Drain the fill solution by depressing cap. Rinse elec-
trode with distilled or deionized water. Drain.
2.
3. Move spring and outer body down cable also.
4. Dry off inner stem and module with a soft tissue.
Holding the body of the electrode gently press the
Release the cap and verify electrode returns to its
original position. (You may need to gently assist for
this to occur).
Unscrew upper cap and slide down cable toward
connector.

12 13
5. Hold inner stem and unscrew module and replace
with a new one. (HI 4114-51).
6. Reassemble electrode (see section VII), and refill with
electrolyte. Soak new membrane in potassium solu-
tion to condition before calibration.
2) Follow section VII; General Guidelines to optimize test
set-up.
3) During calibration it is best to start with lower concen-
tration samples first. Wait for a stable reading before
reading/ recording values. Permit longer equilibra-
tion at these levels (3 or 4 minutes).
4) To prevent carry over and contamination of samples,
rinse sensors with deionized water and dab dry be-
tween samples. Do not rub membrane.
T
y
pical HI 4014 and HI 4114 Linearit
y
-160
-110
-60
-10
40
90
123456
-Log of Concentration
m
V
XIXI
XIXI
XI. Direct Calibration and MeasurementDirect Calibration and Measurement
Direct Calibration and MeasurementDirect Calibration and Measurement
Direct Calibration and Measurement
This method is a simple procedure for measuring many
samples. A direct reading ISE meter (HI 4222 or equiva-
lent) determines concentration of the unknown by a direct
reading after calibrating the meter with the standards. HI
4014-00 ISE is added to both samples and standards to
adjust the ionic strength of the solutions at a dose of 2 mL
per 100 mL standard or sample. The meter is calibrated
with freshly made standards that are in the measurement
range of the unknowns. Unknowns are then read directly.
In the non-linear region, more calibration standards are
required and more frequent calibrations are advised.
A pH/mV meter in mV mode and semi log graph paper
may also be used. Two or more freshly prepared standards
that are in the measurement range of the unknowns (with
ISA added), are measured in mV mode on the meter.
These values are plotted on semi-log paper and the points
are connected to form a straight-line curve. When samples
are measured, their mV values are converted to concentra-
tion by following the mV to the concentration axis on the
semi-log plot.
Procedure:
Follow sections VIII and IX to prepare electrodes for mea-
surement.
1) Follow section VI to prepare standards/ solution. Stan-
dards should bracket and fall within the range of
interest. Standards and solutions should be at the
same temperature.
2 mL of HI 4014-00 is added to 100 mL of
both samples and standards. Add stir bar and mix
before taking measurements.

14 15
XIII.XIII.
XIII.XIII.
XIII. pHpH
pHpH
pH
HI 4014/ HI 4114 potassium electrodes operate over a wide
pH range. The pH range 1.5 - 12 is acceptable for
measurements. Samples and standards can be adjusted to
be within the working pH range.
XIV.XIV.
XIV.XIV.
XIV. Storage and Care of the HI 4014 sensor andStorage and Care of the HI 4014 sensor and
Storage and Care of the HI 4014 sensor andStorage and Care of the HI 4014 sensor and
Storage and Care of the HI 4014 sensor and
HI 4114 electrodeHI 4114 electrode
HI 4114 electrodeHI 4114 electrode
HI 4114 electrode
HI 4014 sensor can be stored in dilute standards near the
sample concentration for short periods of time and should
be disassembled and stored dry in the shipping vial when
not in use for long periods of time. Do not expose module to
elevated temperatures. Refrigeration of module will extend
life time.
HI 4114 combination electrode can be left in dilute stan-
dards near the sample concentration for short periods of
time. If the electrode will be used frequently and needs to
be ready for use, take measures to prevent evaporation of
fill solution. Top off fill solution, replace o-ring, fill hole
cover on the fill hole opening, and place in dilute potas-
sium solution. Store electrode upright. Before using, flush
junction once and top off fill solution.
For long-term storage, disassemble electrode and wash all
salts from assembly with deionized water. Wrap ceramic
junction on inner stem in Parafilm®or other sealing film.
Unscrew module from the inner stem and blot dry. Store
module in shipping vial. Store electrode assembly disas-
sembled. Do not expose module to elevated temperatures.
Refrigeration of module will extend its life.
XVXV
XVXV
XV..
..
. Conversion TConversion T
Conversion TConversion T
Conversion Tablesables
ablesables
ables
Multiply byMultiply by
Multiply byMultiply by
Multiply by
Moles/L (M) K+to ppm K+(mg/L) 39100
ppm K+(mg/L) to M K+(Moles/L) 2.56 X 10-5-5
-5-5
-5
C
sample
=
(V
T
)10
∆E/ S
- (V
S’
)
C
standard
V
standard
V
sample
V
S’
(V
sample
+V
standard
+V
ISA
)= V
T
(V
sample
+V
ISA
)= V
S’
XII.XII.
XII.XII.
XII. Other Measurement TOther Measurement T
Other Measurement TOther Measurement T
Other Measurement Techniquesechniques
echniquesechniques
echniques
Known additionKnown addition
Known additionKnown addition
Known addition
An unknown concentration can be determined by adding a
known amount (volume and concentration) of K+standard
to the sample. mV values are noted before and after the
addition of standard (∆E). An ideal sensor slope can be
used in the equation but actual determined slopes at the
temperature of measurement should be used if known (S).
This method is preprogrammed in the Hanna HI 4222 pH/
ISE/mV meter, which greatly simplifies the method .
Example:
Potassium ion determination with known addition.
1. A 50 mL sample of unknown (VSAMPLE) is placed in an
clean plastic beaker with a thoroughly cleaned elec-
trode (s). Add 1 mL of ISA to sample. Mix. The mV1is
recorded.
2. 5 mL (VSTD) of 10-1M (CSTD) standard is added to the
beaker and the mV value increases. (Note: for other
concentration samples, add a known volume and
concentration of standard to produce approximately
30 mV change).
3. The unknown potassium concentration in the original
sample (CSAMPLE) can then be determined by using the
equation that follows.
The procedure can be repeated with a second standard
addition to verify slope and operation of the method.

16
MAN4114 07/06 REV3
WARRANTYWARRANTY
WARRANTYWARRANTY
WARRANTY
Hanna Instruments Ion Selective Electrodes are warranted
to be free of defects in material and workmanship for 6
months from date of purchase when used for their intended
purpose and maintained according to instructions. If they
fail to work when first used contact your dealer immediately.
Damage due to accidents, misuse, misapplication, tampering
or lack of prescribed maintenance is not covered.
Hanna Instruments reserves the right to modify the design,
construction or appearance of its products without advance
notice.