Hanna Instruments HI 8733 User manual

1
Instruction Manual
HI8633
HI8733 - HI8734
Reliable and Waterproof
Multi-Range
Conductivity Meters
www.hannainst.com

2
Dear Customer,
Thank you for choosing a Hanna Instruments product.
Please read this instruction manual carefully before using these
instruments.
This manual will provide you with the necessary information for correct
use of these instruments, as well as a precise idea of their versatility.
If you need additional technical information, do not hesitate to e‑mail
us at [email protected] or view our worldwide contact list at
www.hannainst.com.
All rights are reserved. Reproduction in whole or in part is prohibited
without the written consent of the copyright owner.

3
PRELIMINARY EXAMINATION .............................................................. 4
GENERAL DESCRIPTION...................................................................... 4
FUNCTIONAL DESCRIPTION & SPECIFICATIONS OF HI8633 ................. 5
FUNCTIONAL DESCRIPTION & SPECIFICATIONS OF HI8733 ................. 6
FUNCTIONAL DESCRIPTION & SPECIFICATIONS OF HI8734 ................. 7
OPERATIONAL GUIDE.........................................................................8
CALIBRATION ...................................................................................9
CONDUCTIVITY VERSUS TEMPERATURE CHART................................... 13
TDS VERSUS TEMPERATURE CHART .................................................. 14
DETERMINING THE TEMPERATURE COEFFICIENT OF A SOLUTION (HI8733).... 15
BATTERY REPLACEMENT................................................................... 16
PROBE MAINTENANCE ..................................................................... 17
ACCESSORIES.................................................................................. 18
TABLE OF CONTENTS

4
HI8633 andHI 8733havebeen designedspecifically forusein theareas
ofproduction and qualitycontrol. It isoftennecessary totestsamples with
different concentrations ranging from deionized water to brine.
Both models can be manually calibrated at 1 point.
TheHI8733,withabuilt‑intemperaturesensorandAutomaticTemperature
Compensation, is the perfect instrument for measuring samples with
fluctuating temperature.
HI8734 has been specially designed for the water conditioning industry,
particularly in the softening, demineralization, reverse osmosis and
drinking water applications.
Three ranges of measurement assure the highest accuracy possible. In
addition, Manual Temperature Compensation is possible through a knob
on the front panel.
The ratio between conductivity and TDS is factory set at 0.5.
Moreover, the 4‑ring potentiometric probes supplied with the meters are
made of rugged PVC ‑ ideal for indoor, as well as outdoor measurements.
Remove the instrument from the packing material and examine
it carefully to make sure that no damage has occurred during
shipping. If there is any noticeable damage, please contact your local
Hanna Instruments Office.
Each meter is supplied with:
• Conductivity probe with DIN connector and 1 m (3.3’) cable:
• HI76301D for HI8633 and HI8734
• HI76302W for HI8733
• Calibration solution sachet
• Instruction manual
• Quality Certificate
• 9V alkaline battery (1 pc.)
Note:Save all packing materials until you are sure that the
instrument functions correctly. Any damaged or defective item
must be returned in its original packing materials together with
the supplied accessories.
GENERAL DESCRIPTION
PRELIMINARY EXAMINATION

5
1) Liquid Crystal Display
2) Measurement range selection keys
3) EC calibration knob
4) Manual temperature compensation knob
5) Temperature selection key
6) On/Off key
Range 0.0 to 199.9 / 0 to 1999 µS/cm
0.00 to 19.99 / 0.0 to 199.9 mS/cm
Resolution 0.1 / 1 µS/cm
0.01 / 0.1 mS/cm
Accuracy
(@ 20 °C/68 °F)
±1% Full scale
excluding probe error
Typical EMC Deviation ±2% Full Scale
Calibration Manual, 1 point, through EC knob
Temperature
Compensation
Manual, 0 to 50 °C (32 to 122 °F) with
β=2%/ °C
Probe (included) HI76301D with 1m (3.3’) cable
Environment 0 to 50 °C (32 to 122 °F); RH max 100%
Battery Type 1 x 9V alkaline
Battery Life Approx. 100 hours of continuous use
Dimensions 145 x 80 x 36 mm (5.7 x 3.1 x 1.4 “)
Weight 230 g (8.1 oz.)
FUNCTIONAL DESCRIPTION &
SPECIFICATIONS OF HI8633

6
Range 0.0 to 199.9 / 0 to 1999 µS/cm
0.00 to 19.99 / 0.0 to 199.9 mS/cm
Resolution 0.1 / 1 µS/cm
0.01 / 0.1 mS/cm
Accuracy
(@ 20 °C/68 °F)
±1% Full scale
excluding probe error
Typical EMC Deviation ±2% Full Scale
Calibration Manual, 1 point, through EC knob
Temperature
Compensation
Automatic, 0 to 50 °C (32 to 122 °F) with
βadjustable from 0 to 2.5%/ °C
Probe (included) HI76302W ATC with 1m (3.3’) cable
Environment 0 to 50 °C (32 to 122 °F); RH max 100% 0to50°C(32to122°F);RHmax100%
Battery Type 1 x 9V alkaline
Battery Life Approx. 100 hours of continuous use
Dimensions 145 x 80 x 36 mm (5.7 x 3.1 x 1.4 “)
Weight 230 g (8.1 oz.)
1) Liquid Crystal Display
2) Measurement range selection keys
3) EC calibration knob
4) Automatic Temperature Compensation coefficient knob
5) On/Off key
FUNCTIONAL DESCRIPTION &
SPECIFICATIONS OF HI8733

7
1) Liquid Crystal Display
2) Measurement range selection keys
3) TDS calibration knob
4) Manual temperature compensation knob
5) Temperature selection key
6) On/Off key
FUNCTIONAL DESCRIPTION &
SPECIFICATIONS OF HI8734
Range 0.0 to 199.9 / 0 to 1999 mg/L
0.00 to 19.99 g/L
Resolution 0.1 / 1 mg/L
0.01 g/L
Accuracy
(@ 20 °C/68 °F)
±1% Full scale
excluding probe error
Typical EMC Deviation ±2% Full Scale
Calibration Manual, 1 point, through TDS knob
Temperature
Compensation
Manual, 0 to 50 °C (32 to 122 °F) with
β=2%/ °C
Probe (included) HI76301D with 1m (3.3’) cable
Environment 0 to 50 °C (32 to 122 °F); RH max 100%
Battery Type 1 x 9V alkaline
Battery Life Approx. 100 hours of continuous use
Dimensions 145 x 80 x 36 mm (5.7 x 3.1 x 1.4 “)
Weight 230 g (8.1 oz.)

8
OPERATIONAL GUIDE
• Each meter is supplied complete with a 9V battery. Remove the
battery compartment cover on the back of the meter (see page 16).
Install the battery while observing its polarity.
• Connect the probe to the meter securely
by aligning the pins with the socket and
pushing the plug in.
• Make sure that the meter has been cali‑
brated before taking any measurements
(see “Calibration” section).
• Immerse the conductivity probe into
the sample, with the holes on the shaft
completely submerged.
If possible, use plastic beakers or con‑
tainers to minimize any EMC interference.
• Tap the probe lightly on the bottom of the beaker to remove any
air bubbles which may be trapped inside the PVC sleeve.
• Turn the instrument on by pressing the On/Off key.
For HI8633 and HI8734:
• Take the temperature of the solution
with a ChecktempC or another accurate
thermometer following LCD indication.
• Press and hold down the Temp key to display the temperature and
adjust the temperature knob to that of the solution e.g. 20 °C.
For HI8733:
• Adjust the TEMPERATURE COEFFICIENT
knob to 2% to compensate for the
temperature effect of average solutions
(to determine exact value for a particular
solution, see page 15).
• Select the appropriate measurement range.

9
Note:If the display shows only a “1” on
the far left hand side, the meter is out of
range. Select the next (higher) range.
• Wait for a couple of minutes for the temperature sensor to reach
thermal equilibrium with the sample before taking measurements.
• After the measurement has been completed, the instrument should
be switched off and the probe should be cleaned and dried (see
“Probe Maintenance” on page 17).
CALIBRATION
Accessories needed:
• Use any calibration solution within the meter’s range. The
solution should ideally be close to the samples being measured.
Use for example HI7030 or HI8030, 12880 µS/cm (=12.88
mS/cm) conductivity solution, for HI8633 and HI8733, and
HI7032, 1382 mg/L (=2764 µS/cm) TDS solution, for
HI8734.
• ChecktempC or another accurate thermometer with 0.1 °C
resolution (not necessary for HI8733).
PROCEDURE FOR HI8633 AND HI8734
• Pour sufficient quantity of a conductivity
(HI8633) or TDS (HI8734) calibration
solution (e.g. HI7030 or HI7032) into a
beaker to cover the holes on the probe. If
possible, use plastic beakers to minimize
any EMC interference.
• Immerse the conductivity probe, making
sure that holes are completely submerged,
and the ChecktempC in the solution.
• Wait for a couple of minutes for thermal
equilibrium to be reached.
• Tap the probe on the bottom, then shake it while rotating to make
sure no air bubbles remain trapped in the sleeve.

10
• Record the temperature of the buffer solution from the thermometer
(e.g. 20 °C).
• Switch the instrument on by pressing On/Off.
• Press and hold down Temp to display the
temperature.
• Adjust the TEMPERATURE knob to display 20 °C.
• Release Temp key to display conductivity measurement.
• Select 19.99 mS/cm (HI8633) or 1999 mg/L (HI8734) range by
pressing the appropriate range key.
• Follow LCD calibration indication. Adjust the calibration knob
until the display shows for HI8633 the conductivity reading at
25 °C (see the conductivity vs. temperature table), e.g. @ 25 °C,
12880 µS/cm = 12.88 mS/cm, or for HI8734 the TDS reading
at 25 °C (see the TDS vs. temperature chart), e.g. @25 °C,
1382 mg/L.
• All subsequent measurements will be compensated to 25 °C (77 °F).
If you prefer to standardize the temperature compensation to 20 °C
(68 °F) rather than 25 °C (77 °F), leave the TEMPERATURE knob at
18°C (if the temperature of the solution is 18 °C), adjust the knob
to read “11.67 mS” (see the conductivity vs. temperature chart) or
“1251 mg/L” (see the TDS vs. temperature chart). All subsequent
measurements will be compensated to 20 °C.

11
PROCEDURE FOR HI8733
• Pour sufficient quantity of a conductiv‑
ity calibration solution (e.g. HI7030/
HI8030) into a beaker to cover the
holes on the probe. If possible, use
plastic beakers to minimize any EMC
interference.
• Immerse the conductivity probe in the
solution, making sure that holes are
completely submerged.
• Wait for a couple of minutes for
thermal equilibrium to be reached.
• Tap the probe on the bottom, then
shake it while rotating to make sure
no air bubbles remain trapped in the
sleeve.
• Switch the instrument on by pressing
On/Off.
• Set the temperature coefficient knob
to 2% to compensate for the tem‑
perature effect of average solutions (to
determine exact value for a particular
solution, see page 15).
• Select 19.99 mS/cm range by pressing
the appropriate range key.
• The calibration is now complete and the instrument is ready for
use.
The instrument should be recalibrated at least once a month, or when
the probe is changed.
Note: For more accurate results, it is advisable to use a calibration
solution close to the measurement range. See the “Accessories”
section for a wide selection of conductivity solutions.

12
• Follow LCD calibration indication. Adjust the calibration knob
until the display shows “12.88 mS” i.e. the conductivity reading
@ 25 °C.
• All subsequent measurements will be compensated to 25 °C
(77 °F).
If you prefer to standardize the temperature compensation to
20 °C (68 °F) rather than 25 °C (77 °F), adjust the knob to read
“11.67 mS” (see the conductivity vs. temperature chart on page
13). All subsequent measurements will be compensated to 20 °C.
• The calibration is now complete and the instrument is ready for
use.
The instrument should be recalibrated at least once a month, or when
the probe is changed.
Note: For more accurate results, it is advisable to use a calibration
solution close to the range to be measured. See the “Accessories”
section for a wide selection of conductivity solutions.

13
The conductivity of an aqueous solution is the measure of its ability to
carry an electrical current by means of ionic motion.
The conductivity invariably increases with increasing temperature.
It is affected by the type and number of ions in the solution and by
the viscosity of the solution itself. Both parameters are temperature
dependent. The dependency of conductivity on temperature is
expressed as a relative change per degree Celsius at a particular
temperature, commonly as percent per °C.
For manual temperature compensation, refer to the following chart:
For instance, the conductivity values of the calibration solutions at
25 °C are 12880 µS/cm, 1413 µS/cm or 5000 µS/cm when using
HI7030, HI7031 or HI7039, respectively.
At 20 °C, the values are 11670 µS/cm, 1278 µS/cm or
4523 µS/cm, respectively. With the solutions at 30 °C, the values are
14120 µS/cm, 1548 µS/cm or 5479 µS/cm, respectively.
ºC ºF HI7030
HI8030
(mS/cm)
HI7031
HI8031
(mS/cm)
HI7033
HI8033
(mS/cm)
HI7034
HI8034
(mS/cm)
HI7035
HI8035
(mS/cm)
HI7039
HI8039
(mS/cm)
0 32 7150 776 64 48300 65400 2760
5 41 8220 896 65 53500 74100 3180
10 50 9330 1020 67 59600 83200 3615
15 59 10480 1147 68 65400 92500 4063
16 60.8 10720 1173 70 67200 94400 4155
17 62.6 10950 1199 71 68500 96300 4245
18 64.4 11190 1225 73 69800 98200 4337
19 66.2 11430 1251 74 71300 100200 4429
20 68 11670 1278 76 72400 102100 4523
21 69.8 11910 1305 78 74000 104000 4617
22 71.6 12150 1332 79 75200 105900 4711
23 73.4 12390 1359 81 76500 107900 4805
24 75.2 12640 1386 82 78300 109800 4902
25 77 12880 1413 84 80000 111800 5000
26 78.8 13130 1440 86 81300 113800 5096
27 80.6 13370 1467 87 83000 115700 5190
28 82.4 13620 1494 89 84900 117700 5286
29 84.2 13870 1521 90 86300 119700 5383
30 86 14120 1548 92 88200 121800 5479
31 87.8 14370 1575 94 90000 123900 5575
CONDUCTIVITY VERSUS
TEMPERATURE CHART

14
The TDS value in aqueous solutions is directly proportional to conduc‑
tivity. The ratio between the two parameters depends on the solution
and usually it is set to a factor of 0.5 (corresponding to a solution of
CaCO3). This means that 1 µS/cm is equal to 0.5 mg/L (ppm) of TDS.
For manual temperature compensation, refer to the following chart:
For instance, the TDS values of the calibration solutions at 25 °C are
1382 mg/L or 12.41 g/L when using HI7032 or HI7036, respectively.
At 20 °C, the values are 1251 mg/L or 11.24 g/L, respectively.
With the solutions at 30 °C, the values are 1515 mg/L or 13.61 g/L,
respectively.
ºC ºF HI7032
mg/L (ppm)
HI7036
g/L (ppt)
0 32 758 6.82
5 41 876 7.88
10 50 999 8.99
15 59 1122 10.10
16 60.8 1148 10.33
17 62.6 1173 10.56
18 64.4 1200 10.78
19 66.2 1224 11.01
20 68 1251 11.24
21 69.8 1277 11.47
22 71.6 1303 11.71
23 73.4 1329 11.94
24 75.2 1358 12.18
25 77 1382 12.41
26 78.8 1408 12.65
27 80.6 1438 12.89
28 82.4 1461 13.13
29 84.2 1476 13.37
30 86 1515 13.61
31 87.8 1541 13.85
TDS VERSUS
TEMPERATURE CHART

15
Highly acidic, alkaline samples or solutions with high salt content might
have a different coefficient than the customary 2% per degree °C.
In order to calculate this coefficient follow the procedure below:
• Immerse the probe of HI8733 in the sample and adjust the
TEMPERATURE COEFFICIENT knob to 0% (i.e. no compensation).
• Condition the sample and probe to 25 °C and note the conductivity
reading, C25.
• Condition the sample and probe to a different temperature t °C
(approximately 10 °C different from 25 °C) and note the conduc‑
tivity reading Ct.
• The temperature coefficient βof the solution is calculated as given
by the following formula:
(Ct‑ C25)
β = 100 x
(t ‑ 25) x C25
The above procedure is suitable for determining the temperature
coefficient in a laboratory or where the temperature of the solution
can be controlled.
If this is not possible (e.g. on‑site measurements), the following
procedure can be used providing the sample temperature varies by at
least 5 °C or preferably 10 °C:
• Immerse the probe of HI8733 in the test solution and turn the
TEMPERATURE COEFFICIENT knob to 0% (no compensation).
• Check the conductivity reading and record the value. Make
sure the reading is stable, i.e. no greater variations than
±0.2 mS/cm within a minute.
• Repeat the procedure when the temperature of the test solution
has changed by at least 5 °C. Wait for the conductivity reading to
stabilize.
• Adjust the TEMPERATURE COEFFICIENT knob until the display shows
the same value as recorded earlier.
• The value indicated by the knob is the temperature coefficient of
the solution.
DETERMINING THE TEMPERATURE
COEFFICIENT OF A SOLUTION (HI8733)

16
When battery becomes weak the meter will display the battery symbol
as empty.
When the low battery indicator appears, the battery has only a few hours
left. A low battery will result in unreliable measurements.
It is recommended to replace the battery immediately.
Battery replacement must only take place in a nonhazardous area using
a 9V alkaline battery.
Unscrew the three screws on the rear of the meter, remove the battery
compartment cover and replace the 9V battery with a new one.
Make sure the battery contacts are tight and secure before replacing
the cover.
BATTERY REPLACEMENT

17
Rinse the probe with tap
water after every series of
measurements. If a more
thorough cleaning is required,
remove the PVC sleeve and
clean the probe with a cloth
or a nonabrasive detergent.
When reinserting the sleeve
onto the probe, be sure that
the sleeve is in the right
direction with the four holes
towards the cable end.
After cleaning the probe,
recalibrate the instrument.
The probe body is in PVC.
For this reason it must never
come into close contact with
a heat source. If the probe is
exposed to high temperatures
(above 50 °C/122 °F), the
rings might become loose or
detached, resulting in a seri‑
ous impairment of the probe.
In such cases, the probe has
to be replaced.
PROBE MAINTENANCE

18
ACCESSORIES
CALIBRATION SOLUTIONS
HI7030L 12880 µS/cm, 500 mL bottle
HI7030M 12880 µS/cm, 230 mL bottle
HI7031L 1413 µS/cm, 500 mL bottle
HI7031M 1413 µS/cm, 230 mL bottle
HI7033L 84 µS/cm, 500 mL bottle
HI7033M 84 µS/cm, 230 mL bottle
HI7034L 80000 µS/cm, 500 mL bottle
HI7034M 80000 µS/cm, 230 mL bottle
HI7035L 111800 µS/cm, 500 mL bottle
HI7035M 111800 µS/cm, 230 mL bottle
HI7039L 5000 µS/cm, 500 mL bottle
HI7039M 5000 µS/cm, 230 mL bottle
HI7032L 1382 ppm (mg/L), 500 mL bottle
HI7032M 1382 ppm (mg/L), 230 mL bottle
HI7036L 12.41 ppt (g/L), 500 mL bottle
HI7036M 12.41 ppt (g/L), 230 mL bottle
CONDUCTIVITY PROBES
HI76301D Conductivity probe with 1m (3.3’) cable and
DIN connector
HI76302W Conductivity probe with built‑in temperature
sensor, 1m (3.3’) cable and DIN connector
OTHER ACCESSORIES
HI98501 Electronic thermometer
(range: ‑50.0 to 150.0°C)
HI710007 Shockproof rubber boot, blue
HI710008 Shockproof rubber boot, orange

19
Hanna Instruments reserves the right to modify the design, construction and
appearance of its products without advance notice.
HI8633, HI8733 and HI8734 are guaranteed for two years against
defects in workmanship and materials when used for their intended
purpose and maintained according to instructions. Electrodes and
probes are guaranteed for six months. This warranty is limited to repair
or replacement free of charge.
Damage due to accidents, misuse, tampering or lack of prescribed
maintenance is not covered.
If service is required, contact your local Hanna Instruments Office.
If under warranty, report the model number, date of purchase, serial
number and the nature of the problem. If the repair is not covered by the
warranty, you will be notified of the charges incurred. If the instrument
is to be returned to Hanna Instruments, first obtain a Returned Goods
Authorization number from the Technical Service department and then
send it with shipping costs prepaid. When shipping any instrument,
make sure it is properly packed for complete protection.
WARRANTY
Before using this product, make sure it is entirely suitable for your
specific application and for the environment in which it is used.
Any variation introduced by the user to the supplied equipment may
degrade the meters' performance. For yours and the meter's safety do
not use or store the meter in hazardous environments.
RECOMMENDATIONS FOR USERS

20
Printed in ROMANIA MAN8734 07/18
World Headquarters
Hanna Instruments Inc.
Highland Industrial Park
584 Park East Drive
Woonsocket, RI 02895 USA
www.hannainst.com
Local Office
Hanna Instruments Inc.
Highland Industrial Park
584 Park East Drive
Woonsocket, RI 02895 USA
Phone: [phone]
Fax: [phone]
e‑mail: [email protected]