Hanna Instruments HI96800 User manual

HI96800
Refractometer for Refractive
Index and Brix Measurements
INSTRUCTION MANUAL
www. .com [e-mail]1.800.561.8187

Thank you for choosing a Hanna Instruments product.
Please read this instruction manual carefully before using
this instrument.
This manual will provide you with the necessary informa‑
tion for correct use of this instrument, as well as a precise
idea of its versatility.
Dear
Customer,
All rights are reserved. Reproduction in whole or in part is prohibited
without the written consent of the copyright owner, Hanna Instruments
Inc., Woonsocket, Rhode Island, 02895, USA.
www. .com [e-mail]1.800.561.8187

3
TABLE OF CONTENTS
Preliminary Examination ........................................................
General Description................................................................
Specifications........................................................................
Principle of Operation............................................................
Functional Description............................................................
Display Elements...................................................................
Measurement Guidelines ........................................................
Calibration Procedure.............................................................
Measurement Procedure.........................................................
To Change Measurement Unit.................................................
To Change Temperature Unit ..................................................
Making a Standard % Brix Solution .......................................
Battery Replacement..............................................................
Error Messages .....................................................................
Accessories............................................................................
13
4
5
7
9
11
15
6
8
12
10
14
16
17
18
www. .com [e-mail]1.800.561.8187

4
Remove the instrument from the packing materials and examine carefully
to ensure no damage has occurred during shipping. If any damage has
occurred, contact your local Hanna Instruments Office.
Each HI96800 instrument is supplied with:
• 9 V battery
• Instruction manual
• Plastic pipette
• Quality Certificate
Note: Save all packing material until you are sure that the instrument
functions correctly. A defective instrument must be returned in its
original packing.
PRELIMINARY EXAMINATION
www. .com [e-mail]1.800.561.8187

5
The HI96800 Digital Refractometer is a rugged portable, water resistant device
that benefits from Hanna Instruments’ years of experience as a manufacturer
of analytical instruments.
The HI96800 is an optical instrument that is both simple and quick. Samples
are measured after a simple user calibration with deionized or distilled water.
Within seconds the instrument measures the refractive index of the sample.
Reading can also be displayed with sucrose temperature compensation
(nD20) or % Brix.
TheHI96800digitalrefractometereliminatestheuncertainityassociatedwith
mechanicalrefractometersandiseasilyportableformeasurementsinthefield.
The measurement technique and temperature compensation employ metho‑
dologyrecommendedintheICUMSA MethodsBook(InternationalCommision
for Uniform Methods of Sugar Analysis).
Temperature (in °C or °F) is displayed simultaneously with the measurement
on the large dual level display along with icons for Low Power and other
helpful message codes.
Key features include:
• Dual‑level LCD
• Automatic Temperature Compensation (ATC)
• Easy setup and storage
• Battery operation with Low Power indicator (BEPS)
• Automatically turns off after 3 minutes of non‑use.
GENERAL DESCRIPTION
www. .com [e-mail]1.800.561.8187

6
SPECIFICATIONS
Range
nD: 1.3300 to 1.5080
nD20:1.3330 to 1.5040
% Brix: 0.0 to 85.0
Temperature: 0.0 to 80.0 °C; 32.0 to 176.0 °F
Resolution
nD: 0.0001
nD20:0.0001
% Brix: 0.1
Temperature: 0.1 °C; 0.1 °C
Accuracy
nD: ±0.0005
nD20:±0.0005
% Brix: ±0.2
Temperature: ±0.3 °C; ±0.5 °F
Temperature
Compensation
Automatic between 10.0 and 40.0 °C
(50.0 ‑ 104.0 °F)
Measurement Time Approximately 1.5 seconds
Minimum Sample
Volume 100 µL (cover prism totally)
Light Source Yellow LED
Sample Cell Stainless Steel ring and flint glass prism
Case Material ABS
Enclosure Rating IP65
Battery Type / Life 9V / 5000 readings
Auto‑Off After 3 minutes of non‑use
Dimensions 192 x 102 x 69mm (7.6 x 4.1 x 2.7”)
Mass 350 g (12.3 oz.)
www. .com [e-mail]1.800.561.8187

7
Refractive Index is an optical characteristic of a substance and the number of
dissolved particles in it. Refractive Index is defined as the ratio of the speed
of light in empty space to the speed of light in the substance. A result of this
property is that light will “bend”, or change direction, when it travels through
a substance of different refractive index. This is called refraction.
When passing from a material with a higher to lower refractive index, there
is a critical angle at which an incoming beam of light can no longer refract,
but will instead be reflected off the interface. The critical angle can be used
to easily calculate the refractive index according to the equation:
sin (θcritical) = n2/ n1
Wheren2istherefractiveindexofthelower‑densitymedium;n1istherefractive
index of the higher‑density medium.
In the HI96800, light from an LED passes through a prism in contact with
the sample. An image sensor determines the critical angle at which the light
is no longer refracted through the sample.
PRINCIPLE OF OPERATION
www. .com [e-mail]1.800.561.8187

8
9. Battery Cover
10. Battery Compartment
1. Liquid Crystal Display (LCD)
2. Secondary Display
3. Primary Display
4. READ Key (User Measurement)
5. ZERO Key (User Calibration)
6. RANGE Key (User Measurement Unit)
7. ON/OFF
8. Stainless Steel Sample Well and Prism
TOP VIEW
BOTTOM
FUNCTIONAL DESCRIPTION
www. .com [e-mail]1.800.561.8187

9
1. Battery (blinks when low battery condition detected)
2. Primary Display (displays measurement and error messages)
3. Measurement in Progress Tag
4. SETUP: Factory Calibration Tag
5. CAL: Calibration Tag
6. Measurement Units
7. Automatic Temperature Compensation
(blinks when temperature exceeds 10‑40 °C / 50‑104 °F range)
8. Temperature Units
9. Secondary Display (displays temperature measurements; when blinking,
temperature has exceeded operation range: 0‑80 °C / 32‑176 °F)
DISPLAY ELEMENTS
www. .com [e-mail]1.800.561.8187

10
• Handle instrument carefully. Do not drop.
• Do not immerse instrument under water.
• Do not spray water to any part of instrument except the “sample well”
located over the prism.
• Do not expose instrument or prism to solvents that will damage it. This
includes most organic solvents and extremely hot or cold solutions.
• Particulate matter in a sample may scratch the prism. Absorb sample
with a soft tissue and rinse sample well with deionized or distilled water
between samples.
• Use plastic pipettes to transfer all solutions. Do not use metallic tools
such as needles, spoons or tweezers as these will scratch the prism.
• To reduce the effects of evaporation or absorption of water when taking
readings over a period of time, the prism and sample well can be covered
with plastic wrap.
MEASUREMENT GUIDELINES
www. .com [e-mail]1.800.561.8187

11
Calibration should be performed daily, before measurements are made, when
the battery has been replaced, between a long series of measurements, or
if environmental changes have occurred since the last calibration.
1. Press the ON/OFF key, then release. Two instrument test screens will
be displayed briefly; all LCD segments followed by the percentage of
remaining battery life. The meter will briefly display an indication of
the measurement units set. When LCD displays dashes, the instrument
is ready.
2. Using a plastic pipette, fill the sample well with distilled or deionized
water. Make sure the prism is completely covered.
Note: If the ZERO sample is subject to intense light such as sunlight
or another strong source, cover the sample well with your hand or
other shade during the calibration.
3. Press the ZERO key. If no error messages appear, your unit is calibrated.
(For a description of ERROR MESSAGES see page 17).
Note: The -0- or 0.0 screen will remain until a sample is measured
or the power is turned off.
4. Gently absorb the ZERO water standard with a soft tissue. Use care
not to scratch the prism surface. Dry the surface
completely. The instrument is ready for sample
measurement.
Note: If the instrument is turned off the
calibration will not be lost.
CALIBRATION PROCEDURE
www. .com [e-mail]1.800.561.8187

12
Verify the instrument has been calibrated before taking measurements.
1. Wipe off prism surface located at the bottom of the sample well. Make
sure the prism and sample well are completely dry.
2. Using a plastic pipette, drip sample onto the prism surface. Fill the well
completely.
Note: If the temperature of the sample differs significantly from
the temperature of the instrument, wait approximately 1 minute to
allow thermal equilibration.
3. Press the READ key. The result is displayed in the selected units.
Note: The last measurement value will be displayed until the next
sample is measured or the instrument is turned off. Temperature will be
continuously updated.
The ATC tag blinks and automatic temperature compensation is
disabled if the temperature exceeds the 10-40 °C/50-104 °F range.
4. Remove sample from the sample well by absorbing with a soft tissue.
5. Using a plastic pipette, rinse prism and sample well with distilled or
deionized water. Wipe dry. The instrument is ready for the next sample.
MEASUREMENT PROCEDURES
.
www. .com [e-mail]1.800.561.8187

13
Press the RANGE key to select measurement units. The instrument scales
each time the key is pressed and the primary display indicated “nd” for
refractive index, “nd20” for temperature compensated refractive index and
“bri” for %Brix, when the instrument displays the screen with 4 dashes,
it is ready for measurement.
TO CHANGE MEASUREMENT UNIT
www. .com [e-mail]1.800.561.8187

14
To change the temperature measurement unit from Celsius to Fahrenheit
(or vice versa), follow this procedure.
1. Press and hold the ON/OFF key continuously for approximately
15 seconds. The LCD will display the “all segment” screen followed by
a screen with the model number on the primary display and the version
number on the secondary display. Continue pressing the ON/OFF key.
2. While continuing to hold the ON/OFF key, press the ZERO key. The
temperature unit will change from °C to °F or vice versa.
TO CHANGE TEMPERATURE UNIT
15
seconds
°C or °F
www. .com [e-mail]1.800.561.8187

15
Note:Solutions above60 %Brix needto bevigorously stirredor shaken
and heated in a water bath. Remove solution from bath when sucrose
hasdissolved.Thetotalquantitycanbe scaled proportionallyforsmaller
containers but accuracy may be sacrificed.
Example with 25% Brix:
%Brix g Sucrose g Water g Total
25 25.000 75.000 100.000
To make a Brix Solution, follow the procedure below:
•Place container (such as a glass vial or dropper bottle that has a cover)
on an analytical balance.
•Tare the balance.
•To make an X% BRIX solution weigh out X grams of high purity Sucrose
(CAS #: 57‑50‑1) directly into the container.
•Add distilled or deionized water to the container so the total weight of
the solution is 100 g.
MAKING A STANDARD % BRIX SOLUTION
www. .com [e-mail]1.800.561.8187

16
To replace the instrument’s battery, follow these steps:
• Make sure the instrument is off.
• Turn instrument upside down and remove the battery cover by turning
it counterclockwise.
• Extract the battery from its location.
• Replace with a new 9V battery making sure to observe polarity.
• Insert the back battery cover and fasten it by turning clockwise to
engage.
BATTERY REPLACEMENT
www. .com [e-mail]1.800.561.8187

17
ERROR MESSAGES
Error Code Description
“Err“ General failure. Cycle power to instrument.
If error persists, contact your local Hanna
Instruments Office.
“LO“ primary
display
Sample exceeds minimum measurement
range.
“HI“ primary
display
Sample exceeds maximum measurement
range.
“LO“ primary
display Cal
segment ON
Wrong solution used to zero instrument.
Use deionized or distilled water. Press
ZERO.
“HI“ primary
display Cal
segment ON
Wrong solution used to zero instrument.
Use deionized or distilled water. Press
ZERO.
“t LO“ primary
display Cal
segment ON
Temperature exceeds ATC low limit
(10.0 °C) during calibration.
“t HI“ primary
display Cal
segment ON
Temperature exceeds ATC high limit
(40.0 °C) during calibration.
“Air“ Prism surface insufficiently covered.
“ELt“ Too much external light for measurement.
Cover sample well with hand.
“nLt“ LED light is not detected.
Contact your local Hanna Instruments
Office.
Battery segment
blinking
<5% of battery life is remaining.
Temperature values
are blinking
“0.0°C“or “80.0 °C“
Temperature measurement
out of range (0.0 to 80.0 °C).
ATC segment
blinking
Outside temperature
compensation range
(10.0 to 40.0 °C).
SETUP segment
blinking
Factory calibration lost.
Contact your local Hanna Instruments
Office.
www. .com [e-mail]1.800.561.8187

18
MAN96800 04/17
ACCESSORIES
Code Description
HI4020-11 50% Brix Standard, 10 mL
HI740157P Plastic refilling pipette (20 pcs.)
HI740029P 9V battery (10 pcs.)
www. .com [e-mail]1.800.561.8187

HI96800 is warranted for two years against defects in
workmanship and materials when used for their intended
purpose and maintained according to instructions.
This warranty is limited to repair or replacement free of
charge.
Damage due to accidents, misuse, tampering or lack of
prescribed maintenance is not covered.
If service is required, contact your local Hanna Instruments
Office. If under warranty, report the model number, date
of purchase, serial number and the nature of the problem.
If the repair is not covered by the warranty, you will be
notified of the charges incurred. If the instrument is to be
returned to Hanna Instruments, first obtain a Returned Goods
Authorization number from the Technical Service depart‑
ment and then send it with shipping costs prepaid. When
shipping any instrument, make sure it is properly packed
for complete protection.
To validate your warranty, fill out and return the enclosed
warranty card within 14 days from the date of purchase.
Hanna Instruments reserves the right to modify the design, construction or
appearance of its products without advance notice.
Warranty
www. .com [e-mail]1.800.561.8187

Printed in ROMANIA
World
Headquarters
Hanna Instruments Inc.
Highland Industrial Park
584 Park East Drive
Woonsocket, RI 02895 USA
Local Office
Hanna Instruments USA
270 George Washington Highway
Smithfield, RI 02917
MAN96800
www. .com [e-mail]1.800.561.8187