Hanover BPC02101F02 User manual


HanoverOutdoorFurniture




IMPORTANT
Ifyouhaveanyproblemswiththisproduct(missingordamagedparts,assemblyissues,etc.),
PLEASEDONOTRETURNTOTHERETAILER/STORE
fromwhereyoupurchasedtheproduct.
PleasecallourToll‐FreeCustomerServiceHotlineat:1‐800‐416‐3511
Between9:00AMand5:00PMEasternTime,MondaythroughFriday
Orvisitourwebsiteat:www.hanover‐products.com


Toexpediteanyfuturewarrantyclaims,pleaseretaintheInstructionSheet,Warranty
Cardandreceiptforfutureuse.
For additionalon‐linesupportonassembly,troubleshootingandcare&maintenanceofyouroutdoor
furniture,pleasevisitourwebsiteat:www.hanover‐products.com.
6/1/2015(a)

BPC02101
Step 4: After making any necessary adjustments to the
alignment of the table legs and the leg connector
bracket, use hex bolt driver to tighten all bolts.
Note: Each bolt must be tightened a few revolutions
at a time. In order to apply equal pressure to all bolt
joints, we recommend working in a cross corner
(X fashion). Repeat until all bolts are tight. Do not
over tighten. Over tightening may strip bolts or
damage the welds or frame. Cover all bolts with
covers.
Step 5: With the help of another person, turn the table in the
upright position. Note the clear bumpers spaced
evenly throughout the inside of the rim. Carefully
place glass inside the rim, resting on the clear
bumpers. Your table is now ready for use. If you
have any questions, please call our Customer Service
Center at 1-800-416-3511.
IMPORTANT NOTE: Damage to welds or frames
resulting from over tightened bolts or improper
assembly is not covered under our warranty. Please
read all instructions carefully before assembly. If you
have any questions regarding your assembly, call our
Customer Service Center at 1-800-416-3511.
IMPORTANT!! PLEASE READ ENTIRE INSTRUCTION SHEET BEFORE ASSEMBLY!!
TO EXPEDITE WARRANTY CLAIMS PLEASE KEEP INSTRUCTION SHEET, WARRANTY CARD AND COPY OF RECEIPT
PARTS LIST ORDER PART #DESCRIPTION
BOLT COVER
HEX BOLT DRIVER
1/4" X 20 MM BOLT
1/4" X 35 MM BOLT
TABLE LEG
LEG CONNECTOR
BRACKET
TABLE RIM
GLASS TOP
QTY
1
12
1
1
1
12
4
8
4
A
B
C
D
E
F
G
H
I
BUMPER
FACTORY ASSEMBLY G0002
HW0105
HW0004
HW0036
HW0142
HW0006
Page 2
FOOT CAP
FOOT CAP
FACTORY ASSEMBLY
Step 1: Carefully remove glass and set aside until Step 5.
Lay glass flat--do not stand glass on edge. Remove
all protective materials and set parts on a flat, non-
abrasive surface. Identify parts packed in carton
against the parts list. If you are missing any parts or
are unsure how to proceed with assembly, call our
Customer Service Center at 1-800-416-3511. Do
not attempt assembly if any parts are missing or
damaged.
Step 2: Place the table rim (without glass) upside down on a
flat, non-abrasive surface. Attach a table leg to the rim
by using a 1/4"x20 mm bolt and a washer as shown in
Figure 1. Guide the bolt through the hole in the table
leg, into the pre-drilled hole in the table rim. Hand
tighten bolt 3-4 revolutions only. Do not tighten
completely. Some adjustments may be necessary to
ensure proper alignment of the table legs. Repeat for the
other three table legs.
Step 3: Build the leg assembly. Attach the legs to the leg
connector bracket by using the 1/4"x35 mm bolts as
shown in Figure 2. Add a washer to each bolt. Guide
these bolts through the holes in the leg connector
bracket, and into the fixed nuts already in place in the
legs. Do not over-tighten. Only 3-4 turns to ensure the
leg stays in position. Repeat this procedure on the
other three legs.
Figure 2
Figure 1
* NOTE: PARTS SHOWN ON PARTS LIST ARE NOT TO SCALE
Ø6.5 X 1.0 MM
WASHER
FC0069
I
H
G
F
H
I
B
D
C
ST1613
ST1614
ST1615