Hanover High Dining Table User manual

HanoverOutdoorFurniture
IMPORTANT
Ifyouhaveanyproblemswiththisproduct(missingordamagedparts,assemblyissues,etc.),
PLEASEDONOTRETURNTOTHERETAILER/STORE
fromwhereyoupurchasedtheproduct.
PleasecallourToll‐FreeCustomerServiceHotlineat:1‐866‐851‐8438
Between9:00AMand5:00PMEasternTime,MondaythroughFriday
Orvisitourwebsiteat:www.hanover‐products.com
Toexpediteanyfuturewarrantyclaims,pleaseretaintheInstructionSheet,Warranty
Cardandreceiptforfutureuse.
For additionalon‐linesupportonassembly,troubleshootingandcare&maintenanceofyouroutdoor
furniture,pleasevisitourwebsiteat:www.hanover‐products.com.
6/1/2015(b)

Dining Table
Owner's Manual
Page 1of 7
If you have any problems with this product, DO NOT RETURN IT TO THE STORE
CALL OUR CUSTOMER SERVICE HOT-LINE AT
1-866-851-8438
Between 9 A.M. - 5 P.M. Eastern Time, Monday through Friday

Page 2 of 7

Page 3 of 7

Page 4 of 7

PART# DESCRIPTION PICTURE QTY
A Table top frame 1
B Table leg 4
C Connector 1
D Glass 1
AA Bolt M6 x 15mm 8
BB Bolt M6 x 25mm 8
CC Washer 16
DD Bolt Cover 16
EE Wrench 1
PARTS LIST
Page 5 of 7

Assembly Steps:
Note: Do not fully tighten bolts until assembly is completed and alignment is correct.
Step 1. Carefully place the table top frame (A) upside down on a non-abrasive surface.
Step 2. Assemble the table legs (B) to the table top (A) with bolts (AA) and washer (CC)
as shown in figure 1.
Figure 1
Step 3. Assemble connector (C) to the table leg (B) with bolts (BB) and washer (CC)
as shown in figure 2.
Step 4. Tighten all bolts with wrench (EE) . Cover all bolts with bolt caps(DD).
Figure 2
Page 6 of 7

Step 5. Verify all bolts are securely tightened before use and turn your table right side up.
Put glass (D) on table top frame(A). Your table is now ready to use. (Figure 3).
Figure 3
Page 7 of 7

Dining Table
Owner's Manual
Page 1of 7
If you have any problems with this product, DO NOT RETURN IT TO THE STORE
CALL OUR CUSTOMER SERVICE HOT-LINE AT
1-866-851-8438
Between 9 A.M. - 5 P.M. Eastern Time, Monday through Friday

Page 2 of 7

Page 3 of 7

Page 4 of 7

PART# DESCRIPTION PICTURE QTY
A Table top frame 1
B Table leg 4
C Connector 1
D Glass 1
AA Bolt M6 x 15mm 8
BB Bolt M6 x 25mm 8
CC Washer 16
DD Bolt Cover 16
EE Wrench 1
PARTS LIST
Page 5 of 7

Assembly Steps:
Note: Do not fully tighten bolts until assembly is completed and alignment is correct.
Step 1. Carefully place the table top frame (A) upside down on a non-abrasive surface.
Step 2. Assemble the table legs (B) to the table top (A) with bolts (AA) and washer (CC)
as shown in figure 1.
Figure 1
Step 3. Assemble connector (C) to the table leg (B) with bolts (BB) and washer (CC)
as shown in figure 2.
Step 4. Tighten all bolts with wrench (EE) . Cover all bolts with bolt caps(DD).
Figure 2
Page 6 of 7

Step 5. Verify all bolts are securely tightened before use and turn your table right side up.
Put glass (D) on table top frame(A). Your table is now ready to use. (Figure 3).
Figure 3
Page 7 of 7