Hanover ORLEANS4PCFP-NVY-B User manual


HanoverOutdoorFurniture




IMPORTANT
Ifyouhaveanyproblemswiththisproduct(missingordamagedparts,assemblyissues,etc.),
PLEASEDONOTRETURNTOTHERETAILER/STORE
fromwhereyoupurchasedtheproduct.
PleasecallourToll‐FreeCustomerServiceHotlineat:1‐800‐416‐3511
Between9:00AMand5:00PMEasternTime,MondaythroughFriday
Orvisitourwebsiteat:www.hanover‐products.com


Toexpediteanyfuturewarrantyclaims,pleaseretaintheInstructionSheet,Warranty
Cardandreceiptforfutureuse.
For additionalon‐linesupportonassembly,troubleshootingandcare&maintenanceofyouroutdoor
furniture,pleasevisitourwebsiteat:www.hanover‐products.com.
6/1/2015(a)

ASSEMBLY INSTRUCTIONS
1
2
Attach the seat frame to the back frame by using four 5/16"x40 mm bolts and washer as shown in
Guide these bolts through the holes in the seat frame, into the fixed nuts already in place in the back frame.
Figure 1.
.Do not over tighten
Attach love seat arm by inserting two mm bolts with washers through the holes in front seat portion
of the love seat frame and into the holes in the love seat arm shown in . Attach back of love seat arm
by inserting two mm bolts with washers through holes in the back portion of love seat frame and into
the holes in the rear portion of the love seat arm as shown in . . Repeat for the
opposite side.
Figure 2
Figure 2 Hand tighten only
5/16"x25
5/16"x40
A
B
H
F
G
C
D
G
EH
GFOOT CAP-1
FH
G
EH
G
FH
3Tighten all bolts using the hex bolt driver provided. Tighten each bolt a few revolutions at a time, alternating
between bolt connections until all bolts are tight.
Cover all bolts with bolt covers provided.
Do not over tighten. Over tightening may strip bolts or
damage the welds or frame.

*NOTE:PARTSSHOWNONPARTSLISTARENOTTOSCALE
PARTS IDENTIFICATION LIST
BGC08006
8
5/16" X 40 MM BOLT
Ø8.5 X 1.5 MM
WASHER
LEFT ARM
RIGHT ARM
BOLT COVER
HEX BOLT DRIVER
FOOT CAP-1
FACTORY ASSEMBLY
HW0005
HW0022
HW0006
FC0030
1
12
HW0275
12
4
5/16" X 25 MM BOLT HW0186
1
1
1
1
BACK FRAME
SEAT FRAME
PARTS LIST DESCRIPTION ORDER PART # QTY
A
B
C
D
E
F
G
H
I
FOOT CAP-2
FACTORY ASSEMBLY FC0308
SK0939
SK0940
SK0941
SK0942

Page 4
ASSEMBLY INSTRUCTIONS
1
2
3
Assemble furniture on a smooth, non-abrasive surface. by using two
5/16"x40 mm bolts and washers as shown in . Guide the bolts through holes in back frame, into
pre-drilled holes in the . and back frame
by using four 5/16"x25 mm bolts and washers as shown in . A
and seat frame by using two 5/16"x25 mm bolts and two 5/16"x40 mm bolts and four washers as
shown in .
Fig.1
Hand tighten only.
Fig.2 Hand tighten only.
Fig.3 Hand tighten only.
Attach the back frame to right arm
right arm Attach the seat frame to right arm
ttach the left arm
to back
B
D
I
G
H
Fig.1
I
G
H
A
Fig.2
I
F
H
I
F
H
C
Fig.3
I
F
H
I
G
H
Attach the complete base to the complete seat by using four 5/16"x40 mm bolts and washers as shown
in . Guide the bolts through holes in base, into the pre-drilled holes in the seat.Fig.4 Hand tighten only.
Using the hex bolt driver provided, tighten all bolts.
Test the operation of glider. Gliding
motion should be smooth. Adjust tension on the glider brackets, nuts and bolts as needed. Cover nuts
and bolts with covers provided.
Do not over tighten bolts. If nuts and bolts are
too tight or too loose, the glider will not function properly.
I
G
H
Fig.4
E
I
G
H

Page 5
*NOTE:PARTSSHOWNONPARTSLISTARENOTTOSCALE
PARTS IDENTIFICATION LIST
G0080
PARTS LIST
HW0695
HEX BOLT DRIVER HW0006
SEAT FRAME
1
1
1
A
B
C
D
E
F
G
H
I
J
DESCRIPTION ORDER PART # QTY
GLIDER BRACKET
FACTORY ASSEMBLY
ST4 8 X 25 BOLT.
FACTORY ASSEMBLY
FOOT CAP
FACTORY ASSEMBLY FC0013
6
5/16" X 25 MM BOLT HW0186
8
5/16" X 40 MM BOLT HW0275
HW0005Ø8.5 X 1.5 MM WASHER
BOLT COVER HW0105 14
BACK FRAME 1
LEFT ARM 1
RIGHT ARM 1
GLIDER BASE W/
GLIDER BRACKET 1
14
SG0154
SG0155
SG0156
SG0157
SG0158
SG0159
BGS12023