Hanover TRADDN11PCSW4 User manual

6/1/2015 (b)
To expedite any future warranty claims, please retain the Instruction Sheet, Warranty
Card and receipt for future use.
Care and Maintenance
Store furniture in an upright position. Be careful to never allow water to build up in frames as this will
cause corrosion and freeze damage in cold climates. Wash all frames with a solution of mild soap and
water. Rinse with clean water and dry with a soft absorbent cloth towel. Frames can be treated with a
liquid wax for maximum protection against UV rays and/or salty, damp air. If your set includes
cushions, slings, and/or an umbrella they may be cleaned by hand with a solution of soap and water
with a clean water rinse. (Never machine wash cushions, slings or umbrella covers as this will result in
shrinkage or damage). After cleaning cushions tip on end and allow to drip dry. (Never use a
commercial or home dryer to tumble dry fabric goods). Do not use bleach or solvents to clean any
product! This will void the warranty.
For additional on‐line support on assembly, troubleshooting and care & maintenance of your outdoor
furniture, please visit our website at: www.hanover‐products.com.
IMPORTANT
If you have any problems with this product (missing or damaged parts, assembly issues, etc.),
PLEASE DO NOT RETURN TO THE RETAILER/STORE
from where you purchased the product.
Please call our Toll‐Free Customer Service Hotline at: 1-877-397-5144
Between 9:00 AM and 5:00 PM Eastern Time, Monday through Friday
Or visit our email us at: [email protected]

6/1/2015 (b)
Outdoor Furniture
1‐Year Limited Warranty Program
For a period of one (1) year after purchase, Hanover (“Manufacturer”) will either repair or replace defective components in accordance
with this Limited Warranty. This warranty is between Manufacturer and the original purchaser and is valid only when accompanied by
the original purchaser’s sales receipt showing original date of purchase and location of purchase. Replacements under this warranty
revert back to the date of original purchase for future warranty.
Manufacturer or its authorized dealer can accept or reject warranty claims based on its findings. This warranty applies in normal
residential use only and is not intended for commercial use. Manufacturer can make substitutions as required of materials,
components, and sub‐components of comparable valueand utility. This warranty is limited to product repair or replacement (to be
determined solely by Manufacturer). Warranty return is limited to only the single affected component.
This warranty covers only manufacturing defects and does not cover normal wear and tear, damage due to acts of nature (such as, but
not limited to freezing or high winds), abuse or misuse, including chemical damage from suntan oil or other chemicals, exposure to
extreme heat or cold, abrasion or excessive weight. This product is intended to be used in standard installations only. This warranty
is invalid if the product is not used for intended purpose. Manufacturer disclaims liability for any aspect of installation and any
inconvenience caused by a defective part of a component.
Certain items are not covered by this warranty. These include, but are not limited to the following:
1. Components subjected to abuse, including abuse intended to simulatefailure.
2. Damages caused by retailer, shipper or installation crew (such as scratches, dents, tears, chips, etc.).
3. Any part which merely exhibits normal wear yet functions essentially as new, including chips, scratches or stretching of
materials and stitching.
4. Tears, punctures, scratches or any damage caused by improper installation or use.
5. Damage to frames/welds resulting from improper assembly or exposure to water and/or sub‐freezing temperatures is not
covered. General frame rusting is notcovered.
6. Fading and/or discoloration of fabrics/cushions/straps/wicker resulting from exposure to the elements, chemicals, oils, fluids
or any other cause are not covered.
7. Umbrella bases are not covered under any circumstances.
8. Items sold “as is” or floor models.
To make a claim, call the toll‐freenumber below. Please have available a copy of the original sales receipt along with a brief
description of the problem. Please also provide your email address and daytime telephone or cell phone#. All items may be
charged actual freight costs plus $15 for handling. Repairs or replacement will be made at the Manufacturer’s option. Sales and use
taxes, plus shipping and handling charges are the responsibility of the consumer.
THIS IS THE ENTIRE EXCLUSIVE EXPRESS LIMITED LIABILITY. THE MANUFACTURER NEITHER MAKES NOR IS RESPONSIBLE FOR ANY OTHER
WARRANTIES, EITHER EXPRESS OR IMPLIED, INCLUDING THOSE OF RETAILING DEALERS. THIS EXCLUSIVE REMEDY IS LIMITED TO RECEIPT OF A CREDIT
IN CONNECTION WITH THE REPAIR OR REPLACEMENT OF ANY PRODUCT OR COMPONENT DEEMED TO BE DEFECTIVE UNDER THE TERMS AND
CONDITIONS AS STATED IN THIS WARRANTY. NEITHER HANOVER, THE PRODUCT MANUFACTURER NOR ITS AGENTS SHALL BE LIABLE IN ANY CASE FOR
INCIDENTAL, INDIRECT, SPECIAL OR CONSEQUENTIAL DAMAGES RESULTING FROM THE USE OF THIS PRODUCT OR ARISING OUT OF ANY BREACH OF
THIS WARRANTY OR NEGLIGENCE EVEN IF IT HAS BEEN ADVISED OF THE POSSIBILITY OF SUCH DAMAGES. EXCEPT AS OTHERWISE MAY BE REQUIRED
BY LAW, THERE ARE NO OTHER EXPRESS OR IMPLIED WARRANTIES OTHER THAN THE WARRANTY DESCRIBED HEREIN, AND ALL OTHER WARRANTIES,
INCLUDING ANY IMPLIED WARRANTY OF MERCHANTABILITY OR FITNESS FOR A PARTICULAR PURPOSE ARE EXPRESSLY DISCLAIMED.
Contact Warranty Services at 1-877-397-5144
or [email protected]
www.hanover‐products.com

Page 4
*NOTE:PARTSSHOWNONPARTSLISTARENOTTOSCALE
PARTS IDENTIFICATION LIST
AAF06000
PARTS LIST ORDER PART #DESCRIPTION
AFOOT CAP
FACTORY ASSEMBLY
FC0030
A

PARTS LIST DESCRIPTION ORDER PART #
NUT COVER
BOLT COVER
HEX BOLT DRIVER
HEX WRENCH
1/4" NUT
1/4" X 20 MM BOLT
1/4" X 30 MM BOLT
TABLE LEG
LEG CONNECTOR
BRACKET
TABLE TOP
QTY
8
10
1
1
18
8
8
2
4
2
1
1
HW0027
HW0105
HW0006
HW0009
HW0004
HW0014
HW0036
HW0038
FC0007
FOOT CAP
FACTORY ASSEMBLY
A
B
C
D
E
F
G
H
I
J
K
L
MG0003 1
TOUCH-UP PAINT
TOPSIDE SUPPORT
Ø6.5 X 1.0 MM
WASHER
UMBRELLA HOLE
PROTECTIVE RING
FACTORY ASSEMBLY
G0235 & G0236
AT71017
AT71018
AT71019
AT71020
Page 5
*NOTE:PARTSSHOWNONPARTSLISTARENOTTOSCALE
PARTS IDENTIFICATION LIST
ALS43115

Page 4
ASSEMBLY INSTRUCTIONS
1
2
3
Place the table top upside down on a flat, non-abrasive surface. Attach table leg to table top by using a 1/4"x20 mm
bolt and a washer as shown in .
Repeat for the other three legs.
Attach the topside support to the table top by using two 1/4"x20 mm bolts and washers as shown in .
Repeat for the opposite side.
Fig 1
Hand tighten only.
Fig 1 Hand
tighten only.
.
.
Place the leg beneath the table rim corner bracket. Guide the bolt through the
hole in the table rim and into the pre-drilled hole in the table leg.
Attach a leg to the leg connector bracket by carefully guiding the bolts already in place on the table legs (each leg
has two bolts) through the holes in the leg connector bracket. Add a washer and a nut to the end of each bolt as
shown in . Repeat on the other three legs.Fig. 2 Hand tighten only. Attach topside support to leg connector
bracket by using a 1/4"x30 mm bolt and a washer as shown in . Repeat for the other
topside support.
Fig. 2 Hand tighten only.
L
G
HH
F
K
B
Fig.2
After making any necessary adjustments to the alignment of the table legs and the leg connector bracket, use the
hex bolt driver and hex wrench to tighten all nuts and bolts. each bolt and nut must be tightened a few
revolutions at a time. In order to apply equal pressure to all bolt joints, we recommend working in a cross corner
(X fashion). Repeat until all bolts are tight. . Over tightening may strip bolts. Cover all nuts
and bolts with covers.
Note:
Do not over tighten
K
E
H
C
FOOT CAP
D
A
K
E
H
Fig.1