Happy Beds Berlin Fabric Bed Single User manual

Berlin Fabric Bed - Single
Assembly Instructions
Page 2 of 7
For Care and Maintenance of your bed...
• Always assemble in your desired room of use.
• Check all screws and fixings periodically to
ensure they are still secure.
• Do not push or pull this bed as it will cause
damage.
• Always lift this bed with a second person to
prevent damage or injury.
• Keep any sharp objects away from this bed
frame.
For your Health and Safety...
• Please don't not jump on this bed.
• Do not use this bed if you find missing, damaged
or worn parts. Please contact the retailer you
purchased the bed from.
• Please do not use this bed until you have fully
secured all fixings.
• Please keep all small components away from
children.
• Please ensure this bed is on an even, level
surface.
Also...
If your desired room of choice has a non-carpeted surface please ensure that you use some form of
protection and do not place directly on the wooden floor. This will prevent the bed from moving and
therefore collapsing which will void your guarantee..
Before you begin...
1. Please check you have received the correct product.
2. Unpack all boxes and lay out each component on the floor.
3. Check your product for any damage that may be immediately obvious. If damage is identified,
please contact your retailer.
4. Please read through these instructions thoroughly to ensure you have constructed your bed
correctly.

Page 3 of 7
Box 1
A. Headboard (x1)
B. Footboard (x1) C. Slats (x13) D. Legs (x4)
E. M8x30mm Bolts (x8) F. M8x16mm Bolts (x4) G. M8x65mm Bolts (x4)
H. Flat Washer (x8) I. Spring Washer (x8) J. Slat Caps (x26) K. M5 Allen Key (x1)
Box 2
W. Side Rails (x2) X. Left Frame Rail (x1)
M. Spanner (x1)
L. Nuts (x6) N. M8x45mm Bolts (x2)
O. Bed Cross Bar (x1)
P. Corner Pad (x4) R. Metal Hook (x1)
Q. Pull Strap (x1) S. Front and Back Frame Rail (x2)
T. M4 Allen Key (x1) U. Woven Fabric (x1)
Y. Right Frame Rail (x1) Z. Cross Support Bar (x1)
V. M6x16mm Bolts (x10)
All fittings are stored within the zipped compartment of the headboard.

Page 4 of 7
Step 1
Unpack all components from the boxes and check you are not missing anything. Please check these against the list on
page 3 and note that some components are stored within the zipped compartment at the rear of the headboard. Should
you identify any missing components, please contact the retailer you purchased the bed from.
Step 2
Attach 2x Legs (D)to the 1x Headboard (A)and then attach 2x Legs (D)to the 1x Footboard (B).
A
D
B
AB
&

Page 5 of 7
Step 3
Attach 2x Side Rails (W)to 1x Headboard (A)and 1x Footboard (B)using 8x M8x30mm Bolt (E), 8x Spring Washer (I),
8x Flat Washer (H)and 1x M5 Allen Key (K).
B
A
W
W
K
E
I
I
Step 4
Attach the 4x Corner Pads (P)to the Headboard (A), Footboard (B) and Side Rails (W)using M6x16mm Bolts (V)and 1x
M4 Allen Key (T)as shown in step 2. Then attach Bed Cross Bar (P)to the Side Rails (X)using M6x16mm Bolts (V)and
1x M4 Allen Key (T).
B
A
W
W
P
V
T
T
V

Page 6 of 7
Step 6
Attach the Metal Frame (MF) to the pre-fixed Gas Lift (GL) on the inside of the side panels using 2x M8x45mm Bolts (N), 2x
Nuts (L), M5 Allen Key (K)and 1x Spanner (M).
GL
MF
Step 5
Attach the 2x Front and Back Frame Rails (S)to the 1x Left Frame Rail (X)and 1x Right Frame Rail (Y)using 4x
M8x16mm Bolts (V)and 1x M5 Allen Key (K). Then attach the Cross Support Rail (Z)to the 1x Left Frame Rail (X)and
1x Right Frame Rail (Y)using 4x M8x65mm Bolts (G), 4x Nuts (L), M5 Allen Key (K)and 1x Spanner (M). Finally, attach
the 1x Metal Hook (R) to the Rear Frame Rail (S).
S
S
V
Z
K
A1
K G
L
M
RT

Page 7 of 7
Step 7
Slot each Slat Cap (J)on to the end of each Slat (C). Then press firmly into each Left Frame Rail (X)and Right Frame Rail
(Y). Do not attempt to push the ottoman frame down before applying the mattress as this will cause damage to the
pistons and void your warranty.
C
J
X
Step 8
Turn the bed frame over on to its side and attach the Woven Fabric (U)to the base of the bed frame as shown below.
U