Happy Beds Sienna Fabric Bed 4ft6 User manual

Sienna Fabric Bed 4ft6
Assembly Instructions
www.happybeds.co.uk
Important beforeassembly:
Read these instructions carefully before assembling orusing the product.
Please check the contents of the boxes before attempting to assemble this product. The instructions will
have a checklist of parts and fittings.
It would be sensible to lay a rug or a carpet on the floor where you intend to assemble the product,
to void scratches and damaging the product or the floor.
Assemble the product as close to its intended final location/room as possible.
Do NOT use any power tools as this may damage the frame.
Health & Safety:
This product or some parts of this product will be heavy. Please use an assistant when lifting.
DO NOT jump on the product or any of its parts.
DO NOT use this product if any parts are missing, damaged or worn.
DO NOT use this product unless all fixings are secured.
Please keep small parts out of reach of children.
Always use on a level, even surface.
Please keep these instructions for future reference.

@
This product or some parts of this product will be heavy. Please use an assistant
when lifting.
Never drag or push the pieces across a hard or stone floor as this will cause
damage to the joints. Use a carpet or a rug for extra care.
If you have problems assembling or have damaged or missing pieces, please
contact us by visiting:
https://www.happybeds.co.uk/customer-service
(Not metal)
These tools are not
necessary, but may
help to assemble
certain parts of the
product.
Do NOT use any power
tools as this may
damage the frame.

Page 3 of 6
Box 1
A. Headboard (x1)
Box 2
B. Side Rails (x2) C. Centre Support Rail (x1)
Box 3
D. Footboard (x1) E. Support Leg (x2) F. Slats (x26)
G. Legs (x4) H. M8x30mm Bolts (x20) I. Nuts (x4) J. Flat Washer (x8) K. Spring Washer (x8)
L. M5 Allen Key (x1) M. Spanner (x1) N. Slat Caps (x26) O. Centre Slat Caps (x13) P. M8x40mm Bolts (x4)
All fittings are stored within the zipped compartment of the headboard.

Page 4 of 6
Step 1
Unpack all components from the boxes and check you are not missing anything. Please check these against the list on
page 3. Should you identify any missing components, please contact the retailer you purchased the bed from.
Step 2
Attach 2x Legs (G)to the 1x Headboard (A)and then attach 2x Legs (G)to the 1x Footboard (D)using the Allen Key (L)
and 4x M8x30mm Bolts (H). Please do not use any power tools for this assembly as it will void your guarantee.
G
L
H

Page 5 of 6
Step 3
Next, attach 2x Support Leg (E) to 1x Centre Support Rail (C) using 4x M8x40mm Bolts (P), Allen Key (L), 4x Nuts (I)
and Spanner (M).
L
C
P
I
E
M
Step 4
Attach 2x Side Rails (B)to1x Headboard (A)and1x Footboard (D)using 8x M8x30mm Bolt (H), 8x Spring Washer (K), 8x
Flat Washer (J)and1x M5 Allen Key (L). Then attach 1x Centre Support Rail (C) to1x Headboard (A) and 1x Footboard (D)
using M8x30mm Bolt (H) and 1x M5 Allen Key (L).
A
D
B
H
J
K
L
C
H
L

Page 6 of 6
Step 5
Slot each Slat Cap (N)on tothe end of each Slat (C). Then slot each Slat (J) intoeach Centre Slat Cap (O) Press firmly
intoeach Slat Rail located on the inside of Side Rail (SR) andthen intothe Centre Support Rail (C).
N
F
F
SR
O
C

www.happybeds.co.uk
General Care & Maintenance
Please dispose of all packaging safely.
Wipe clean with a slightly damp cloth.
Avoid the use of all household cleaners and abrasives.
Periodically check all screw & fixings to ensure they are secure.
When moving your product, carefully lift into place. Never drag or push the pieces across the
floor as this will cause damage to the joints and could result in failure to the product that will
invalidate the warranty.
For more information on cleaning and product care visit:
https://www.happybeds.co.uk/help-and-advice
We’ve tried to make this product as easy to assemble as possible. In the unlikely event that
you have problems putting it together or have damaged or missing pieces, please contact
us by visiting:
https://www.happybeds.co.uk/customer-service
Notes