Happy Beds Chloe 7 Drawer Dressing Table User manual

Title of Product
Assembly Instructions
www.happybeds.co.uk
Important before assembly:
.
Health & Safety:
.
Read these instructions carefully before assembling or using the product.
Please check the contents of the boxes before attempting to assemble this product. The instructions will
have a checklist of parts and fittings.
It would be sensible to lay a rug or a carpet on the floor where you intend to assemble the product, to avoid
scratches and damaging the product or the floor.
Assemble the product as close to its intended final location/room as possible.
Do NOT use any power tools as this may damage the frame.
This product or some parts of this product will be heavy. Please use an assistant when lifting.
Please keep small parts out of reach of children.
Always use on a level, even surface.
DO NOT jump on the product or any of its parts.
DO NOT use this product if any parts are missing, damaged or worn.
DO NOT use this product unless all fixings are secured.
Please keep these instructions for future reference.
Chloe 7 Drawer Dressing Table

@
This product or some parts of this product will be heavy. Please use an assistant
when lifting.
Never drag or push the pieces across a hard or stone floor as this will cause
damage to the joints. Use a carpet or a rug for extra care.
If you have problems assembling or have damaged or missing pieces, please
contact us by visiting:
https://www.happybeds.co.uk/customer-service
(Not metal)
These tools are not
necessary, but may
help to assemble
certain parts of the
product.
Do NOT use any power
tools as this may
damage the frame.

of
Drawers Tray
Smaller Drawer Front
Mirrored Panel
Smaller Division
1
1
78
14 1
Lower Tray Front
29
4
3
79
11
22
18
13
1
29
Page
1
1
30
1
15
17
1
Backboard
Rear of Drawer Larger
Left Side of Drawer Larger
Left Side of Drawer Smaller 1
30
78
Descripion
1
1
18
25
07 79
14
19
10
12
Qty
1
1
Upper Left Side
07
1
Larger Division
1
Bottom of Drawer
Lower Tray Rear
1
Larger Drawer Front
21 Rear of Drawer Smaller
22
25
Upper Right Side
4
1
Parts List
7
4
3
1
3
Top Base
1
3
4
Lower Right Side
Part
Right Side of Drawer Smaller
28
Box
Right Side of Drawer Larger
1
20
19
Lower Plinth
02
01
05
12
13
17
1
21
15
22
20
06
28
101
02
1
05
11
06
10
19
Top
1
Lower Left Side
1
1
1
2
1
1
1
1
1
1
1
1
1
1
Vendor: S000139

Allen Key
VC
Mirror Support
P5
VD
3,5 x 14 mm Screw
Structural Screw Cover
Bushing
R
E4
Drawer slide left
F
3
Handle
5,0 x 60 mm Screw
3,5 x 14 mm Screw
Drawer slide right
** You will need a small mallet and a screwdriver for assembly.
** Some screws and wooden dowel may remain.
** Wall plug and screw is supplied to attach strap to the wall.
of
Qty
Glue
6,0 x 8 mm Screw
VA
S
O
L
E9
E
A1
Metallic slide the right field
N
19
4,5 x 45 mm Screw
10 x 10 mm Tack
Bore patch adhesive
Cam Lock
Simple Minifix Screw
8 x 50 mm Wooden Dowel
4,0 x 40 mm Screw
8 x 30 mm Wooden Dowel
Page
Descripion
Hardware List
Part
Smalll Plastic foot
Strap
Structural Screw
S2
M
J
A2
Metallic slide the left field
VB
Vendor: S000139
0 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16
I
H
G
D
B3
A
1
1
6
1
1
64
4
1
2
14
1
12
22
22
14
28
16
62
8
5
7
7
7
7
7

4
Insert hardware part E using small mallet (not provided). Then attach the hardware part VA using the
hardware part P5 and a screwdriver (not provided).
Step 2:
12
Insert hardware part E using small mallet (not provided).
Step 1:
of
DO NOT use any power tools as this may damage the frame and will invalidate any claim.
DO NOT use any power tools as this may damage the frame and will invalidate any claim.
Step 3:
13
02
Attach the hardware part J to the top (02) using the a screwdriver (not provided).
Page 19
07
DO NOT use any power tools as this may damage the frame and will invalidate any claim.
Vendor: S000139
E
E
E
E
E
J
J
J
J
J
J
J
J
P5
VA
E
P5
ATTENTION FOR POSITION
FOR UP
FOR FRONT
1st HOLE
MARKING

Attach hardware part E using a small mallet (not provided) and to the hardware part A1.
20
19
21
4X
18
19
78
of
Insert hardware part E using small mallet (not provided).
4X
79
3X
DO NOT use any power tools as this may damage the frame and will invalidate any claim.
Step 6:
DO NOT use any power tools as this may damage the frame and will invalidate any claim.
Page
4X
3X
3X
DO NOT use any power tools as this may damage the frame and will invalidate any claim.
Step 4:
Step 5:
5
Attach hardware part E using a small mallet (not provided) and to the hardware part A1.
A1
E
E
E
E
E
E
E
E
E
E
E
E
A1

Step 7:
DO NOT use any power tools as this may damage the frame and will invalidate any claim.
Step 8:
06
Insert hardware part E using small mallet (not provided). Then attach the hardware part VB using the
hardware part P5 and a screwdriver (not provided).
05
19
DO NOT use any power tools as this may damage the frame and will invalidate any claim.
6
10
Insert hardware parts E and F using small mallet (not provided).
Page of
Vendor: S000139
MARKING
FOR FRONT
1st HOLE
FOR UP
ATTENTION FOR POSITION
VB
P5
P5
P5
P5
P5
P5
E
F
E
E
E
E
E
F
E

DO NOT use any power tools as this may damage the frame and will invalidate any claim.
4X
3X
19
DO NOT use any power tools as this may damage the frame and will invalidate any claim.
7
30
17
28
Step 10:
Step 9:
28
Attach the hardware part E to the smaller division (28) using a small mallet (not provided) and attach
the hardware part VB using the hardware part R and a screwdriver (not provided). Then rotate the part (28)
and attach the hardware part VA using the hardware part R and a screwdriver (not provided).
Attach the hardware part J to the drawers front (17 and 30) using the a screwdriver (not provided).
Page of
J
J
J
J
R
VB
R
VA
R
E
E
R
ATTENTION FOR POSITION
ATTENTION FOR POSITION
FOR UP
FOR UP 1st HOLE
FOR FRONT
1st HOLE
FOR FRONT
Vendor: S000139

of 8
Insert hardware part E using small mallet (not provided). Then attach the hardware part E4 using the
hardware part S and a screwdriver (not provided).
Attach the hardware part E to the larger division (25) using a small mallet (not provided) and attach
the hardware part VA using the hardware parts R, P5 and a screwdriver (not provided). Then rotate the part
(28) and attach the hardware part VB using the hardware part R and a screwdriver (not provided).
Step 12:
Step 11:
Page
25
11
DO NOT use any power tools as this may damage the frame and will invalidate any claim.
25
19
DO NOT use any power tools as this may damage the frame and will invalidate any claim.
IMPORTANT!
It's essential to fixing the accessory "E " for safety.
Vendor: S000139
P5
VA
ATTENTION FOR POSITION
FOR UP
FOR FRONT
1st HOLE
MARKING
R
VB
ATTENTION FOR POSITION
FOR UP 1st HOLE
FOR FRONT
R
E
R
R
P5
P5
P5
P5
E
E
E
E
E
E
E
E
E
S

05
11
DO NOT use any power tools as this may damage the frame and will invalidate any claim.
19
05
Join the top base (01) to the assembled section using hardware part G, H and I.
9
06
Step 13:
01
Attach the upper left side (05) and the upper right side (06) to the mirrored panel (11) using hardware
part G, H and I.
Step 14:
DO NOT use any power tools as this may damage the frame and will invalidate any claim.
ofPage
I
H
G
G
I
GI
I
G
F
IG
G
I
H
G
Vendor: S000139

19
Page
05
10
02
DO NOT use any power tools as this may damage the frame and will invalidate any claim.
Step 15:
DO NOT use any power tools as this may damage the frame and will invalidate any claim.
02
28
Join the smaller division (28) to the assembled section using hardware part L and a screwdriver
(not provided).
Join the top (02) to the assembled section using hardware part O and a screwdriver (not provided).
Step 16:
of
ATTENTION
The drum lock "L" can be on the left or right as details beside
O
O
LL
LL
L
L
OR
Vendor: S000139

13
of
DO NOT use any power tools as this may damage the frame and will invalidate any claim.
Attach the lower left side (07) to the drawers tray (12) and lower plinth (13) using hardware part G,
H and I.
19
12
25
13
Attach the larger division (25) to the drawers tray (12) and lower plinth (13) using hardware part G,
H and I.
Step 17:
07
11 Page
Step 18:
DO NOT use any power tools as this may damage the frame and will invalidate any claim.
I
G
I
G
G
G
Vendor: S000139

19
Page 12
25
10
DO NOT use any power tools as this may damage the frame and will invalidate any claim.
of
Step 19:
07
25
10
15
1
Insert the lower tray front (14) and lower tray rear (15) to the larger division (25) using hardware part G,
H and I. Then attach the lower right side (10) to the lower tray front (14) and lower tray rear (15) using hardware
part G, H and I.
DO NOT use any power tools as this may damage the frame and will invalidate any claim.
Step 20: Attach hardware part A2 to the o the lower left side (07), larger division (25) and lower right side (10)
using hardware part N and small mallet (not provided).



















Vendor: S000139

DO NOT use any power tools as this may damage the frame and will invalidate any claim.
19
DO NOT use any power tools as this may damage the frame and will invalidate any claim.
Page
10
of
12
Step 21:
13
Insert hardware part D to the drawers tray (12) using a screwdriver (not provided).
25
0

Join the top (02) to the lower left side (07), larger division (25) and lower right side (10) using hardware
part L and a screwdriver (not provided).
Step 22:





Vendor: S000139

of 19
14
Step 23:
2
Page
Step 24: To secure the item to the wall use hardware parts A, B3 and E9 using a drilling machine (not provided)
and a screwdriver (not provided). Then attach hardware part S to the item with a screwdriver (not provided).
DO NOT use any power tools as this may damage the frame and will invalidate any claim.
Attach the backboard (29) to the assembled section using hardware part N using a small mallet
(not provided).
DO NOT use any power tools as this may damage the frame and will invalidate any claim.
Vendor: S000139


S
2º
A
E9
B3
1º
N
N
N
N
N
N
N
N
N
N

Step 25: Attach the left side of drawer larger (78) and right side of drawer larger (79) to the rear of drawer larger
(21) and bottom of drawer (22) using hardware part O and a screwdriver (not provided).
of
8
78
7

Page
Attach the larger drawer front (17) to the left side of drawer larger (78) and right side of drawer larger
(79) using hardware part A1, L and a screwdriver (not provided). Then insert the hardware part M to the left
side of drawer larger (78) and right side of drawer larger (79).
15
DO NOT use any power tools as this may damage the frame and will invalidate any claim.
19
DO NOT use any power tools as this may damage the frame and will invalidate any claim.
Step 26:



Vendor: S000139








Page
1
DO NOT use any power tools as this may damage the frame and will invalidate any claim.
Step 28:
8
19
16
of
Step 27:
DO NOT use any power tools as this may damage the frame and will invalidate any claim.
Attach the handle S2 to the drawer front (17) using hardware part P5 and a screwdriver (not provided) .
Attach the hardware part VC and VD to the left side of drawer larger (78) and right side of drawer
larger (79) using the hardware part P5 and a screwdriver (not provided).
Vendor: S000139
Marking
S2
P5
P5
VD
VC
P5
P5
P5
P5
THE UNDERSIDE OF THE DRAWER

19
18
0
of
Step 29:
Attach the smaller drawer front (30) to the left side of drawer smaller (18) and right side of drawer
smaller (19) using hardware part A1, L and a screwdriver (not provided). Then insert the hardware part M to the
left side of drawer smaller (18) and right side of drawer smaller (19).
Attach the left side of drawer smaller (18) and right side of drawer smaller (19) to the rear of drawer
smaller (20) and bottom of drawer (22) using hardware part O and a screwdriver (not provided).
19
DO NOT use any power tools as this may damage the frame and will invalidate any claim.
17 19
Page
DO NOT use any power tools as this may damage the frame and will invalidate any claim.
Step 30:

30
18
Vendor: S000139
O
O



1

19
18
0
of
Step 29:
Attach the smaller drawer front (30) to the left side of drawer smaller (18) and right side of drawer
smaller (19) using hardware part A1, L and a screwdriver (not provided). Then insert the hardware part M to the
left side of drawer smaller (18) and right side of drawer smaller (19).
Attach the left side of drawer smaller (18) and right side of drawer smaller (19) to the rear of drawer
smaller (20) and bottom of drawer (22) using hardware part O and a screwdriver (not provided).
19
DO NOT use any power tools as this may damage the frame and will invalidate any claim.
17 19
Page
DO NOT use any power tools as this may damage the frame and will invalidate any claim.
Step 30:

30
18
Vendor: S000139
O
O



1

DO NOT use any power tools as this may damage the frame and will invalidate any claim.
Step 31: Attach the handle S2 to the drawer front (30) using hardware part P5 and a screwdriver (not provided).
DO NOT use any power tools as this may damage the frame and will invalidate any claim.
Step 32:
18
of 19
Page
18
30
Attach the hardware part VC and VD to the left side of drawer smaller (18) and right side of drawer
smaller (19) using the hardware part P5 and a screwdriver (not provided).
THE UNDERSIDE OF THE DRAWER
Marking
Vendor: S000139
P5
P5
S2
VC
VD
P5
P5
P5
P5