Vivo DESK-E3CTB User manual

Black 63" x 55" Corner Electric Desk
Scan the QR code with your mobile device or follow the link
for helpful videos and specifications related to this product.
Instruction Manual
https://vivo-us.com/products/desk-e3ctb
SKU: DESK-E3CTB
[email protected]om www.vivo-us.com 309-278-5303
Chat live with an agent!
GET IN TOUCH | Monday-Friday from 7:00am-7:00pm CST

2
If you do not understand these directions, or if you have any doubts about the safety of the installation,
please call a qualified technician. Check carefully to make sure there are no missing or defective parts.
Improper installation may cause damage or serious injury. Do not use this product for any purpose that is
not explicitly specified in this manual and do not exceed weight capacity. We cannot be liable for damage
or injury caused by improper mounting, incorrect assembly, or inappropriate use.
WARNING!
PACKAGE CONTENTS
A (x3)
Desktop
B x2)
Side Bracket
C (x2)
Foot
D (x1)
Le Leg
E(x1)
Leg with Motor
F (x1)
Center Leg
G x1)
Short Sync Rod
I (x5)
Connecting Plate
J(x1)
Le Crossbar
K(x1)
Inner Le
Crossbar
ELECTRICAL SAFETY INSTRUCTIONS
THIS PRODUCT IS POWERED BY ELECTRICITY. IN ORDER TO AVOID BURNS, FIRE AND ELECTRIC
SHOCK, PLEASE READ THE FOLLOWING INSTRUCTIONS CAREFULLY.
• DO NOT CLEAN PRODUCT WHILE POWER IS CONNECTED.
• DO NOT DISASSEMBLE OR REPLACE COMPONENTS WHILE POWER IS CONNECTED.
• NEVER OPERATE THE SYSTEM WITH A DAMAGED CORD OR PLUG. PLEASE CONTACT YOUR
SELLER TO REPLACE DAMAGED PARTS.
• NEVER OPERATE SYSTEM IN DAMP ENVIRONMENTS OR IF ANY ELECTRICAL COMPONENTS HAVE
MADE CONTACT WITH LIQUIDS.
• ALTERATIONS OF THE GIVEN POWER UNIT ARE NOT ALLOWED.
• OUTDOOR USE IS PROHIBITED.
WARNING: CHOKING HAZARD
SMALL PARTS - NOT FOR CHILDREN UNDER 3 YEARS. ADULT SUPERVISION IS REQUIRED.
L (x1)
Inner Right
Crossbar
M x1)
Right Crossbar
N (x1)
Inner Crossbar
O(x1)
Crossbar
Connector
H x1)
Long Sync Rod
P (x1)
Control
Panel
Q (x1)
AC Adapter
S-A x8)
M8x47
S-B (x6)
M6x10
S-C (x10)
M6x12
S-D (x8)
M6x35
S-E (x45)
M5x16
T-A (x1)
5mm Allen Wrench
T-B (x1)
2mm Allen Wrench
T-C (x1)
4mm Allen Wrench
S-F (x21)
Rubber Pad
S-G (x2)
Cable Clip
SOME EXTRA HARDWARE INCLUDED MAY NOT BE USED.
R (x4)
Foot Pad

3
ASSEMBLY STEPS
STEP 1
Attach Le Crossbar (J) to Le Leg (D) and Right Crossbar (M) to Leg With Motor (E) with M8x47 Screws
(S-A). Tighten using 5mm Allen Wrench (T-A).
176lbs
(80kg)
DO NOT EXCEED WEIGHT CAPACITY.
Failure to do so may result in serious injury.
TOOLS NEEDED
Phillips
Screwdriver
Drill
Level
SOME EXTRA HARDWARE INCLUDED MAY NOT BE USED.
B
GS=5mm
B
S=5mm
A
A
A
B
B
C
C
D
E
FG
H
I
J
K
L
M
N
O
P
Q
T-A
M
ED
S-A
J

4
STEP 1 (Continued)
STEP 2
Attach Side Brackets (B) to Le Leg (D) and Leg With Motor (E) using M6x10 Screws (S-B) and 4mm
Allen Wrench (T-C). Mount Feet (C) to Le Leg (D) and Leg With Motor (E) using M6x35 Screws (S-D)
and tighten using 5mm Allen Wrench (T-A). Attach Foot Pads (R) to Feet (C).
Attach Inner Le Crossbar (K) and Inner Right Crossbar (L) to Center Leg (F) using M8x47 Screws (S-A)
and 5mm Allen Wrench (T-A).
S=4mm
S=4mm
C
S=5mm
A
E
Foot (x4)
S=5mm
C
B
T-C
T-A
R
R
S-B
S-D
S-D
S-B
D
E
L
K
S-A
T-A S=5mm
S-A
S=5mm
F

5
STEP 3 - OPTION A: Le Side Extension
STEP 4 - OPTION A: Le Side Extension
Slide Inner Crossbar (N) into Right Crossbar (M) and Inner Right Crossbar (L). Secure using M6x12 Screw
(S-C) and 4mm Allen Wrench (T-C). Attach Crossbar Connector (O) to Inner Le Crossbar (K) and Le
Crossbar (J) using M6x12 Screw (S-C) and 4mm Allen Wrench (T-C). For correct position of Crossbar
Connector (O), use 1st and 2nd holes from le, and 2nd and 3rd holes from right.
S=4mm
Recommended
Installation Position
Rubber Pad(x19)
S=2mm
Assemble the rubber pad
T-C
S-C
N
GH
Insert the Short Sync Rod (G) into Le Leg (D). Loosen the nut on the Short Sync Rod, then extend the
rod onto Center Leg (F) and tighten the nut. Insert the Long Sync Rod (H) into right side of Center Leg
(F) and extend the rod onto Leg with Motor (E) and tighten the nut. Tighten both set screws on the end
of the Short and Long Sync Rods (G, H) using the 2mm Allen wrench (T-B). Insert Rubber Pads (S-F)
into the desktop mounting holes in the desk frame assembly.
S-F
T-B
M
L
S-C
K
J
T-C
DFE
S-F
Loosen the nut
on the Sync Rods
(G, H).
Insert the Sync
Rods (G, H) into
the hex holes in
Legs (F, D) and
turn them counter
clockwise until they
it reach their lowest
positions.
Insert the other end
of Sync Rods (G,
H) into the slots on
Legs (F, E). Secure
the Sync Rods (G, H)
to the slots by
tightening the
pre-installed set
screw using 2mm
Allen Wrench (T-B)..
Retighten the nut
O
T-B
T-B
S-F
Insert Rubber Pads (S-F).Retighten the nut.

6
STEP 5 - OPTION A: Le Side Extension
Position Desktops (A) on frame assembly with center section aligned lengthwise with le section.
Mount Desktops (A) to frame assembly using M5x16 Screws (S-E) and a Phillips screwdriver. Connect
Desktop (A) sections using Connecting Plates (I) and M5x16 Screws (S-E). Tighten using Phillips
Screwdriver.
NOTE: Mounting holes in Desktops (A) for Side Brackets (B) and Connecting Plates (I) are pre-drilled.
For other locations, Screws (S-E) may be driven directly into Desktops (A) by applying pressure while
turning Screws (Screws have sharp ends for self-tapping).
F
F
S-E P
S-E
Mount Control Panel (P) to the underside Desktop (A) using M5x16 Screws (S-E) and a Phillips
screwdriver.
S-E
A
S-E
I
B
A

7
STEP 6 - OPTION A: Le Side Extension
Connect the AC Adapter (Q) to the cable from the motor and Control Panel (P), then plug the AC
Adapter (Q) into a wall outlet to power on the desk for operation. Organize cables using the Cable
Clips (S-G).
Cable Clip (x2)
Q
S-G
S-G
P

8
H
J
H
D
S=4mm
Installation steps for right
L
Rubber Pad(x19)
J
HS=2mm
Recommended
Installation Position
H
J
H
D
S=4mm
Installation steps for right
L
Rubber Pad(x19)
J
HS=2mm
Recommended
Installation Position
STEP 7 - OPTION B: Right Side Extension
Slide Inner Crossbar (N) into Le Crossbar (J) and Inner Le Crossbar (K). Secure using M6x12 Screw
(S-C) and 4mm Allen Wrench (T-C). Attach Crossbar Connector (O) to Inner Right Crossbar (L) and
Right Crossbar (M) using M6x12 Screw (S-C) and 4mm Allen Wrench (T-C). For correct position of
Crossbar Connector (O), use 2nd and 3rd holes from le, and 1st and 2nd holes from right.
O
NS-C
T-C
G
H
Loosen the nut on the Short Sync Rod (G), and Insert the Short Sync Rod (G) into the right side of
Center Leg (F). Then extend the rod onto Leg with Motor (E) and tighten the nut. Insert the Long Sync
Rod (H) into Le Leg (D), extend the rod onto Center Leg (F) and tighten the nut. Tighten both set
screws on the end of the Short and Long Sync Rods (G, H) using the 2mm Allen wrench (T-B). Insert
Rubber Pads (S-F) into the desktop mounting holes in the desk frame assembly.
S-F
T-B
J
K
S-C
L
M
F
E
D
S-F
S-F
T-B
T-B
Loosen the nut
on the Sync Rods
(G, H).
Insert the Sync
Rods (G, H) into
the hex holes in
Legs (F, D) and
turn them counter
clockwise until they
it reach their lowest
postions.
Insert the other end
of Sync Rods (G, H)
into the slots on Legs
(F, E). Secure the
Sync Rods (G, H) to
the slots by
tightening the
pre-installed set
screw using 2mm
Allen Wrench (T-B).

9
F
Assemble the desktop
F
STEP 8 - OPTION B: Right Side Extension
Position Desktops (A) on frame assembly with center section aligned lengthwise with right section.
Mount Desktops (A) to frame assembly using M5x16 Screws (S-E) and a Phillips screwdriver. Connect
Desktop (A) sections using Connecting Plates (I) and M5x16 Screws (S-E). Tighten using Phillips Screw-
driver.
NOTE: Mounting holes in Desktops (A) for Side Brackets (B) and Connecting Plates (I) are pre-drilled.
For other locations, Screws (S-E) may be driven directly into Desktops (A) by applying pressure while
turning Screws (Screws have sharp ends for self-tapping).
I
S-E A
S-E P
S-E
Mount Control Panel (P) to the underside Desktop (A) using M5x16 Screws (S-E) and a Phillips
screwdriver.
S-E
B
A

10
Cable Clip (x2)
K
Assemble the controller
K
STEP 9 - OPTION B: Right Side Extension
Connect the AC Adapter (Q) to the cable from the motor and Control Panel (P), then plug the AC
Adapter (Q) into a wall outlet to power on the desk for operation. Organize cables using the Cable
Clips (S-G).
Q
S-G
S-G
P