Happy Beds HIGHGATE Wooden 1 Drawer Lamp Table User manual

Title of Product
Assembly Instructions
www.happybeds.co.uk
Important before assembly:
.
Health & Safety:
.
Read these instructions carefully before assembling or using the product.
Please check the contents of the boxes before attempting to assemble this product. The instructions will
have a checklist of parts and fittings.
It would be sensible to lay a rug or a carpet on the floor where you intend to assemble the product, to avoid
scratches and damaging the product or the floor.
Assemble the product as close to its intended final location/room as possible.
Do NOT use any power tools as this may damage the frame.
This product or some parts of this product will be heavy. Please use an assistant when lifting.
Please keep small parts out of reach of children.
Always use on a level, even surface.
DO NOT jump on the product or any of its parts.
DO NOT use this product if any parts are missing, damaged or worn.
DO NOT use this product unless all fixings are secured.
Please keep these instructions for future reference.
HIGHGATE Wooden 1 Drawer Lamp Table

ASSEMBLY INSTRUCTIONS
HIGHGATE 1 DRAWER LAMP TABLE
Page 1 of 7
IMPORTANT: READ THESE INSTRUCTIONS CAREFULLY BEFORE ASSEMBLING OR USING YOUR
HIGHGATE 1 DRAWER LAMP TABLE.
PLEASE KEEP THESE INSTRUCTIONS FOR FUTURE REFERENCE.
HEALTH & SAFETY:
DO NOT use this item if any parts are missing, damaged or worn.
DO NOT use this item unless all fixings are secured.
Please keep small parts out of reach of children.
Always use on a level, even surface.
It is recommended that two people handle and assemble the item.
Birlea advise you use the wall straps provided to further enhance the safety of this product.
CARE & MAINTENANCE:
Assemble in the room of use.
To avoid damages assemble the item on a soft, clean surface
Periodically check all screws & fixings to ensure they are secure.
DO NOT push the item as this will damage the base.
Always lift the item with two people to reposition.
Keep any sharp objects away from the item.
This product is manufactured in pine which is a wood with natural characteristics including knots, grains,
clusters or indentations.
On unpacking the item you may notice an odour due to production processes but this will disappear after a
period of time.
DO NOT place the item next to a radiator or direct sunlight - this item is susceptible to temperature change.
It is recommended an even room temperature be maintained with no sudden fluctuations.
DO NOT place hot or cold items directly onto the surface of the item as marking will occur
For general cleaning use a duster or damp cloth (almost dry) not wet - do not use soap and water,
detergents, aerosol sprays or any polish as use of these materials would invalidate any claims.
DO NOT place the item onto wet or damp flooring as staining may occur to the floor.
Vendor: S000398
www.birlea.com

@
This product or some parts of this product will be heavy. Please use an assistant
when lifting.
Never drag or push the pieces across a hard or stone floor as this will cause
damage to the joints. Use a carpet or a rug for extra care.
If you have problems assembling or have damaged or missing pieces, please
contact us by visiting:
https://www.happybeds.co.uk/customer-service
(Not metal)
These tools are not
necessary, but may
help to assemble
certain parts of the
product.
Do NOT use any power
tools as this may
damage the frame.

** WARNING: THE USE OF POWER TOOLS TO ASSEMBLE THIS PRODUCT WILL INVALIDATE
ANY CLAIM AND MAY DAMAGE THIS PRODUCT MAKING IT UNSAFE. Page 2 of 7
PARTS LIST HARDWARE LIST: Carton 1 of 1
Part Description Qty Part Description Qty
1Top Panel 1ACAM NUT 15mm 20
BCAM BOLT 20
CWOOD DOWEL M6 x 25mm 20
D 4
ECSK SCREW M3.5 x 12mm 12
FPAN HEAD SCREW M3.5 x 12mm 2
GTXM MOON HANDLE 1
H1
I
J
1
KPVC NAIL 4 NAIL 12
Carton 1 of 1:
2Left Panel 1
3Right Panel 1
4 Bottom Panel 1
5 Attach Rail 1
6Left Front & Right Back Post Panel 2
7Left Back & Right Front Post Panel 2
8Drawer Front Panel 1
** You will need a screwdriver and a small mallet
( NOT provided)
1
2
3
4
5
7
6
7
6
8
9
10
11
12
13
9Drawer Back Panel 1
10 Drawer Left Panel 1
11 Drawer Right Panel 1
12 Drawer Bottom Panel 1
13 Back Panel 1
METAL RUNNER TRUCK 14"
METAL RUNNER 14"
CSK SCREW M4 x 38mm
Vendor: S000398

Page 3 of 7
1A20
B20
C20
4
H
Insert hardware part A & part B using a screwdriver
(not provided).
Insert hardware part C using a small mallet (not provided). Insert hardware part J using a
small mallet (not provided).Attach hardware H with screw E using screwdriver (not
provided).
DO NOT use any power tools as this may damage the frame and will invalidate any claim.
A
3
2
11
10
4
8
7
6 x2
7 x2
5
A
AA
A
AA
AA
A
A
A
A
A
A
A
A
A
A
B
BB
B
B
B
B
B
B
B
C
CC
C
C
C
C
C
C
C
C
C
C
CC
C
C
C
C
C
J
JJ
J
E
H
J
6
E
HH
1
Vendor: S000398

Page 4 of 7
CA
B
CA
B
23
7
6
6
7
3
4
5
2
6
7
Attach the Left Front & Right Back Post Panel (6) and Left Back
& Right Front Post Panel (7) to Left Panel (2) and Right Panel (3) by screwdriver (not provided).
DO NOT use any power tools as this may damage the frame and will invalidate any claim.
2
3Attach the Bottom Panel (4) and Attach Panel (5) To Left Panel (2) and Right Panel (3) by screwdriver (not
provided).
DO NOT use any power tools as this may damage the frame and will invalidate any claim.
Vendor: S000398

Page 5 of 7
1
24
13
34
4
5
K
K12
CA
B
Attach the Top Panel (1) To Left Panel (2) and Right Panel (3)
by screwdriver (not provided).
DO NOT use any power tools as this may damage the frame and will invalidate any claim.
K
Attach the Back Panel (13) with Nail (K) by small mallet (not provided).
DO NOT use any power tools as this may damage the frame and will invalidate any claim.
Vendor: S000398

Page 6 of 7
6
7E 6 Insert Drawer Bottom Panel (12) as shown and fix Drawer Front Panel (8) by screwdriver (not
provided).
Fix hardware (I) onto the Drawer Left Panel (10) and Drawer Right Panel (11) using screw (E)
by screwdriver (not provided).
DO NOT use any power tools as this may damage the frame and will invalidate any claim.
10
11
9
12
11
9
8
12
11
CA
B
D4Attach the Drawer Left Panel (10) and Drawer Right Panel (11)
to Drawer Back Panel (9) with screw (D)by screwdriver (not provided).
DO NOT use any power tools as this may damage the frame and will invalidate any claim.
D
D
D
D
EEE
E
E
E
I
I
I 1
Vendor: S000398

8F 2
Page 7 of 7
Fix Handle (G) using screw (F) onto Drawer Front Panel (8)
by screwdriver (not provided).
DO NOT use any power tools as this may damage the frame and will invalidate any claim.
1
2
8
F
F
G
G
G1
. Additional Information:
. For complete product information, images and dimension diagrams please visit the website
www.birlea.com
. If you have any issues with your item please contact the retailer directly you purchased it from who
will be able to resolve any issues with Birlea.
. Why don't you send us photos of your assembled furniture to [email protected] to be shared in our
#birleahome feature on lnstagram.
Vendor: S000398

www.happybeds.co.uk
General Care & Maintenance
Please dispose of all packaging safely.
Wipe clean with a slightly damp cloth.
Avoid the use of all household cleaners and abrasives.
Periodically check all screw & fixings to ensure they are secure.
When moving your product, carefully lift into place. Never drag or push the pieces across the
floor as this will cause damage to the joints and could result in failure to the product that will
invalidate the warranty.
For more information on cleaning and product care visit:
https://www.happybeds.co.uk/help-and-advice
We’ve tried to make this product as easy to assemble as possible. In the unlikely event that
you have problems putting it together or have damaged or missing pieces, please contact
us by visiting:
https://www.happybeds.co.uk/customer-service
Notes