DREAMS SANA User manual

62
17
8
9
Headboard
Footboard
Side Panel - Left
Side Panel - Right
Metal Slat Frame
Angle Brackets
2
Cross Bar
Mattress Stoppers
1
10 2
11
Slat Frame Support Rail (wood)
Base Boards
Base Board Support Rails (wood) 4
Ref. Qty
Ref. Description
5
SANA STORAGE BED
Parts Identification
Qty
1
2
3
1
1
1
Parts Checklist
Description
4 1
Page 1 of 8
5
1
2
6
9
7
160510
PLEASE READ
this sheet prior to assembly to familiarise
yourself with the various stages of construction. Carefully
open the pack supplied and check the contents against the
parts and fittings check list.
Do not destroy any of the packaging until you are certain
that you have all the necessary parts for the assembly.
Please ensure that the packaging is disposed of in
a safe environmentally friendly way.
CAUTION: There are small components used in the
construction of this unit. These loose items should be
diovaot,ylbmessagnirudnerdlihcgnuoymorfyawatpek
the danger of choking.
IMPORTANT: BEFORE STARTING TO ASSEMBLE THE BED - PLEASE READ THESE INSTRUCTIONS CAREFULLY.
1
FABRIC
HANDLE
10
11
3
4
HEADBOARD END
FOOTBOARD END
8

Fittings Checklist
Additional Tools Required Care & Maintenance
Page 2 of 8
QtyCode Description
Ax20
C
x20
Spring Washers (for M8 bolts)
D
E
Qty
Code Description
B
Spring Washers (for M8 bolts)
B
Allen Key (for M8 bolt) x1
x3
Bolts (M8x30mm) for
fitting side panels (3&4) and
to headboard & footboard (1&2)
Flat Washers (for M8 bolts)
I
x1
Spanner (for M8 nut)
Metal Plates (for M8 bolts)
x6
GNuts (for M8 slat frame bolts)
x6
x6
F
HARDWARE NEEDED FOR BED ASSEMBLY (PACK A)
x20
CFlat Washers (for M8 bolts)
x16
HARDWARE FOR FITTING METAL SLAT FRAME (PACK B)
Screws (5x50mm) for
fitting wooden support rail
(9) to footboard (2)
Bolts (M8x50mm) for fitting
Metal Slat Frame (5) to
slat frame support bars
x4
J
Bolts (M8x20mm) for fitting
Metal Plates (K) to Metal
Slat Frame (5)
x2
K
Cross-head Screwdriver
In the unlikely event of missing or damaged parts, please
contact the customer service team on 0344 292 00 00.
When calling this number, please quote the part code
reference numbers shown in this leaflet when
requesting spare or replacement parts.
Please retain your assembly instruction and
tools provided for future use.
Periodically check that all bolts are still tight.
This assembly
Approximate time to
assemble this product
requires two persons.
General Hints & Tips When they are supplied and are
part of the assembly of this bed,
ensure that the barrel nuts are
fitted the correct way so the
hole in the nut is facing towards
the intersecting hole in the panel.
Intersecting
Hole
We recommend the bed is
assembled in
the room it shall be
located in.
QtyCode Description Qty Code Description
HFlange Lock-Nuts (M8) for
gas-lift pistons x2
1 HOUR

Stage
1
Page 3 of 8
Bed Assembly - Use Pack 'A'
A x12 B x12 C x12
D
x1
2
1
PLEASE DO NOT TIGHTEN ANY BOLTS YET.
Fit two sets of bolts (A), spring washers (B) , and flat washers (C) to the holes in the headboard (1) as shown.
Note: Do not tighten fully but leave 10mm protruding as in the diagram.
Fit the side panels (3 & 4) to the headboard locating the brackets behind the flat washers.
Fit the other two sets of bolts through the brackets into the central set of holes.
Tighten them all but loosely for now.
A
B
C
3
&
4
1
A
B
C
10mm
1
3
&
4
A
B
C
10mm
2
3
&
4
Note: Do not tighten fully but leave 10mm protruding
Tighten them all loosely for now.
Fit two sets of bolts (A), spring washers (B),
and flat washers (C) to the holes in the
footboard (2) as shown.
as in the diagram.
Fit the side panels (3 & 4) to the footboard locating
the brackets behind the flat washers.
3
4

2
6
3
A
BC
4
&
Square up the bed to 90 degrees - then using sets of
bolts (A), spring washers (B) & flat washers (C) fit
angle brackets (6) into threaded inserts in the corners
of footboard (2) & the side panels (3&4).
Once all four corners are located tighten
all the bolts using the Allen key (D).
Stage
2
Page 4 of 8
Bed Assembly - Use Pack 'A'
A x8 B x8 C x8
D
x1
Stage
3
11
3
34
&
11
4
iv)
vi)
Fix the base board support rails (11) to both side panels.
IMPORTANT: Be careful not to scratch the leather or fabric
when slotting the wooden supports into the side panel brackets.
MAKE CERTAIN THE BED IS
SQUARED
UP, AS SHOWN IN THE DIAGRAM .
v)
44
32

4
Page 5 of 8
10
Stage
5
i) Carefully fit Base Boards (10).
9
2
E
ii)
Using four sets of bolts (J) & flat washers (C)
dedaerhtotni)K(etalplatemehtfoseceipowttif
insertson top of the Slat frame (5). Using Allen
key (D), tighten them 100%.
ii)
x3
E
Fit base boards - Use Pack 'A'
C x4
D
x1 x4
J
x2
K
2
5
5
Fitting Slat Frame - Use Pack ‘B’
Stage
On the marked line in the centre of the
footboard (2), fix slat frame support rail
(9) using screws (E).
i) Open Metal Slat frame (5).
Note that the screws drive straight into
the footboard, there are no pilot holes.
C
K
J
x2

Page 6 of 8
6
I x1
B x4 C x8
D
x1 x4
G
x4
F
iii) With help from your assistant, lift slat
frame (5) onto slat frame support bars
aligning labeled holes on slat frame with
first set of holes in support bars (nearest
to headboard).
iv) Using two bolt sets on each side, (F),(C),
(B) & (G), loosely fix slat frame to the
other four holes - finger tight.
Fitting Slat Frame - Use Pack ‘B’
Stage
HOLD THEM FORWARD
ii)
i) UN-TIE THE TWO MECHANISMS
5
3
Slat Frame Support Bar
3
F
C
B
C
IG
Bolt into centre of long holes
4

7
Page 7 of 8
7
CROSS BAR FITS HERE
NOTE: IT IS VERY IMPORTANT
THAT THIS CROSS-BAR IS FITTED TO
MAINTAIN THE STRENGTH OF THE FRAME
LABEL
7
HEADBOARD END
D
F
C
G
B
C
I
7
I x1
B x2 C x4
D
x1 x2
G
x2
F
Fitting Cross Bar - Use Pack 'B'
Stage
8
Stage
10mm
Carefully hold cross bar (7) in position under the first set of holes in
the support bars.
The holes to use for cross bar are clearly labeled - look carefully at the
drawing. Note that the cross bar must be fitted in this position
otherwise the gas lift cylinders will be damaged.
Using last two bolt sets (F), (C), (B) & (G) loosely clamp cross bar
to underside of the slat frame support bars.
Carefully lay frame down. Make sure there is an even
gap each side of about 10mm, as in the sketch.
Hold frame then tighten all six bolt sets 100% using spanner (I) & Allen key (D).
Fitting Slat Frame - Use Pack 'B'
I x1
D
x1

Stage
9
Page 8 of 8
Stage
10
Push x2 Mattress Stoppers (8) into metal frame, they should go all the
way through the upper & lower metal sections.
H x2 Ix1
Fitting Slat Frame - Use Pack 'B'
During this next step, the assistant should hold up the
slat frame.
On side panels (3&4), slide gas-lift piston stems (X)
onto the axles (Y) then fit the flange lock-nuts (H).
Tighten nuts with spanner (I) - DO NOT over-
tighten. A small gap is left so stems can move
freely - this is important - see sketch below.
Note: Be very careful what
you store under the bed -
the top of an item, like a
suitcase or a box, must not
touch the slats or they shall
be damaged. Maximum
storage height is 185 mm.
3
4
3
4
SMALL GAP
I
H
(X)
(Y)
3
H
8
Note: Before fitting the mattress, carefully move slat frame up and down against the piston pressure
making sure it slides easily. It is better that two people do this making sure all the mechanism is free.
Note that it shall be stiff to start with. Place frame in the lower position then place mattress on top of
the slats. Depending on the weight of the mattress, the speed of the lift will vary when lifting or
lowering so be careful until you get used to the relevant speed with your own weight of mattress.
Always use the fabric handle to lift or lower the frame - keep fingers well away from the moving parts.