Happy Beds Lynx 2 Door Sliding MirroredWardrobe User manual

Lynx 2 Door Sliding Mirrored
Wardrobe
Assembly Instructions
www.happybeds.co.uk
Important before assembly:
Read these instructions carefully before assembling or using the product.
Please check the contents of the boxes before attempting to assemble this product. The instructions will
have a checklist of parts and fittings.
It would be sensible to lay a rug or a carpet on the floor where you intend to assemble the product,
to void scratches and damaging the product or the floor.
Assemble the product as close to its intended final location/room as possible.
Do NOT use any power tools as this may damage the frame.
Health & Safety:
This product or some parts of this product will be heavy. Please use an assistant when lifting.
DO NOT jump on the product or any of its parts.
DO NOT use this product if any parts are missing, damaged or worn.
DO NOT use this product unless all fixings are secured.
Please keep small parts out of reach of children.
Always use on a level, even surface.
Please keep these instructions for future reference.

@
This product or some parts of this product will be heavy. Please use an assistant
when lifting.
Never drag or push the pieces across a hard or stone floor as this will cause
damage to the joints. Use a carpet or a rug for extra care.
If you have problems assembling or have damaged or missing pieces, please
contact us by visiting:
https://www.happybeds.co.uk/customer-service
(Not metal)
These tools are not
necessary, but may
help to assemble
certain parts of the
product.
Do NOT use any power
tools as this may
damage the frame.

11 151 82 10 134 50 167 9
Vendor: S000139
3 12 146
12
13
14
Top Panel
Shelf
Top Plinth
Left Panel
Right Panel
Shelf Divider
Back Support
Front Support
Page
2
Back Rail
Bottom Plinth
Left Door
Right Door
Back Panel
Base Panel
10
09
10
14
04
05
02
09
09 08
07
09
06
03
01
13
13
12
11
W5
W6
** You will need a small mallet and a screwdriver for
assembly.
** Some screws and wooden dowel may remain.
** Wall plug and screw is supplied to attach strap to
the wall.
4
2
V4
3.5 x 20mm Screw
Qty
1
1Bushing
A 5 x 60 mm Screw
Identification of Accessories
DescripionPart
B3
of
Metalic Angle Plates
B5
3
28
1
9
4
4
20
4
28
14
25
L
N 10 x 10mm Tack
Simple Minifix ScrewJ
F 8 x 50mm Wooden Dowel
Plastic Cap
Recycle
M
Cam Lock
Double Minifix ScrewK
E7
E9
Small Plastic Foot
Strap
E 8 x 30mm Wooden Dowel
Metal Claw 7
C1
2P5 3,5 x 14mm Screw
Handle W4
2
Open Rail Support
V5 1
T 3.5 x 25mm Screw 6
Upper Pulley
W3A
4
Lower Pulley
W3B
Door Stopper
W3C
1
4.5 x 25mm Screw
W3D
1
4 x 14mm Screw
W3E
32
13
3.5 x 14mm Screw
S
Hanging Rail
R4 1
Bottom Runner
Top Runner
2
Z4
Rail Support
1
1
2
2
2
2
1
1
1
1
1
1
1
Box
1
1
1
1
2
1
1
2
4
1
1
1
1
1
1
1
1
Qty
Parts List
DescripionPart
09
01
02
03
04
05
06
07
08
10
11

V4
B5
J
S
E
J
W3E
J
W3B
W3E
W5
E
J
P5
E
E
W3E
W3E
W3E
T
E
J
J
E7
J
J
N
N
E7
J
J
J
J
EF
E
E
W3E
V5
V4
W4
T
T
T
W3C
W3D
W3B
W3E
W3A
W3A
W3E
W3E
Vendor: S000139
W4
E
EW3E
W3E
J
E
E
Z4
JJ
J
J
N
E7
N
E7
J
JE
J
E
W3E
E
E
E
E
E
E
T
S
T
3 of
Prepare these parts for assembly using hardware parts B5, E, E7, F, J, N, P5, S, V4, V5, W3A, W3B,
W3C, W3D, W3E, W4, W5 and Z4. You will need to use a small mallet and a screwdriver (not provided).
2x
09
03
01
14
02
05
04
Central fixing
the handle adjustable
12
10
2x
11
06
DO NOT use any power tools as this may damage the frame and will invalidate any claim.
Page
Step 1:
9

E
K
L
F
E
F
M
ML
L
Vendor: S000139
L
L
L
K
9
Step 2:
4 Page
09
07
07
14
Attach the back rails (9) to the back support (7) using hardware parts E, K and L with a small mallet and
screwdriver (not provided).
DO NOT use any power tools as this may damage the frame and will invalidate any claim.
09
07
09
Attach the back support (7) and front support (8) to the base panel (14) using hardware parts F, L and
M with a small mallet and a screwdriver (not provided).
DO NOT use any power tools as this may damage the frame and will invalidate any claim.
Step 3:
08
09
of

Vendor: S000139
ML
L
K
ML
L
L
M
M
M
M
L
Page
Step 4:
Step 5:
01
08
07
06
DO NOT use any power tools as this may damage the frame and will invalidate any claim.
Attach the shelf (2) using hardware parts K, L and M with a screwdriver (not provided).
DO NOT use any power tools as this may damage the frame and will invalidate any claim.
02
02
of 5 9
Attach the self divider (6) and the top panel (1) using hardware parts L and M with a screwdriver (not
provided).

L
L
Vendor: S000139
M
L
M
L
L
L
L
Page 6
Attach the bottom plinths (10) to the right panel (5). Step 6:
10
05
DO NOT use any power tools as this may damage the frame and will invalidate any claim.
DO NOT use any power tools as this may damage the frame and will invalidate any claim.
Step 7:
10
05
of 9
Join the assembled inner frame section of the assembled side frame section using hardware parts L
and M with a screwdriver (not provided).

Vendor: S000139
W3E
M
M
W3E
W3E
W3E
M
M
L
L
LL
L
L
L
Position the hanging rail R4 then attach the left panel (4) using hardware parts L and M with a
screwdriver (not provided)
Put the back panels (13) in place and fix the bottom runner W6 using hardware part W3E and a
screwdriver (not provided).
W6
ofPage 7
Step 9:
1,34"
13
04
1º
DO NOT use any power tools as this may damage the frame and will invalidate any claim.
2º
13
9
R4
Step 8:
DO NOT use any power tools as this may damage the frame and will invalidate any claim.

C1
N
N
C1
S
N
N
N
N
C1
N
S
W3E
W3E
Vendor: S000139
C1
C1
N
C1
N
N
C1
of
DO NOT use any power tools as this may damage the frame and will invalidate any claim.
Step 10:
8
Page
03
DO NOT use any power tools as this may damage the frame and will invalidate any claim.
Step 11:
9
Secure the back panels (13) using hardware parts C1 and N with a small mallet (not provided). Attach
the top plinth (3) using harware part S with screwdriver (not provided).
1º
2º
12
11
Attach the doors (11) and (12) as shown in the diagram.

 
Vendor: S000139
E9
A

B3

9
To secure the item to the wall use hardware parts A, B3 and E9 using a drilling machine (not provided)
and a screwdriver (not provided).Then attach hardware part S tothe item with a screwdriver (not provided).
Birlea Furniture advise you use the wall straps provided to further enhance the safety of this product.
ofPage 9
Step 12:

www.happybeds.co.uk
General Care & Maintenance
Please dispose of all packaging safely.
Wipe clean with a slightly damp cloth.
Avoid the use of all household cleaners and abrasives.
Periodically check all screw & fixings to ensure they are secure.
When moving your product, carefully lift into place. Never drag or push the pieces across the
floor as this will cause damage to the joints and could result in failure to the product that will
invalidate the warranty.
For more information on cleaning and product care visit:
https://www.happybeds.co.uk/help-and-advice
We’ve tried to make this product as easy to assemble as possible. In the unlikely event that
you have problems putting it together or have damaged or missing pieces, please contact
us by visiting:
https://www.happybeds.co.uk/customer-service
Notes