Happy Beds WILSON STORAGE BED 5FT User manual

WILSON STORAGE BED
5FT
ASSEMBLY INSTRUCTIONS
Page 1 of 10

Page 2 of 10
REQUIRE 2 PEOPLE TO ASSEMBLE

No Part List Qty Box
A Headboard 1 pc 1
B Footboard 1 pc 2
C Side Rail 2 pcs 3
D Metal Frame Bed 1 set
E U-bracket 2 pcs
F Base Handle 2 pcs 4
G Hydraulic Base Support 2 pcs
H Hydraulic Pump 2 pcs
I Support Leg 1 pc
J Cross Bar 1 pc 3
K Bottom Bed Base 2 pcs 5
A
B
C
C
D
G
H
J
K
I
F
E
E
Page 3 of 10
No Hardware List Qty Box
1 JCBC M6 x 45mm 8 pcs
2 JCBC M6 x 80mm 2 pcs
3 JCBB M8 x 16mm 10 pcs
4 JCBB M8 x 20mm 12 pcs
5 JCBB M8 x 40mm 8 pcs
6 JCBB M8 x 45mm 6 pcs
7 M8 Flat Washer 8 pcs 3
8 M6 Hex Nuts 10 pcs
9 M8 Hex Nuts 6 pcs
10 M6 Spanner 1 pc
11 M8 Spanner 1 pc
12 Allen Key M4 1 pc
13 Allen Key M5 1 pc
14 L-Shape Metal Corner Bracket 2 pcs 4

C
C
J
C
C
A
B
B
2x
C
B
4
13
AC
4
13
2x
13
3
C
133
J
2x
2x
C
B
14
14
Step 1:
To fix the left side rail (C) and right side rail (C) to the headboard (A) and footboard (B) you will need to use hardware
parts 4 with the M5 allen key (13).
Step 2:
To fix the L-SHAPE BRACKET (14) to the footboard (B) you will need to use hardware parts 3 with the M5 allen key (13).
In order to make sure the side rail not bend inside, you will need to fix the part Support Center (J), by using hardware (3)
with Allen Key M5 (13)
DO NOT fully tighten the screw part until all the screw is in the right hole position.
Page 4 of 10
4 JCBB M8 x 20mm 12 pcs
13 Allen Key M5 1 pc
3 JCBB M8 x 16mm 10 pcs
13 Allen Key M5 1 pc
14 L-Shape Metal Corner Bracket 2 pcs
Do Not Use Power Tools

11
7 5 13
C
C
C
G
H
G
11H
H
G
G
2x 2x
2x
Step 3:
To install Hydraulic (H) to the (G), you will need to loose out the M8 HEX nut from the part (G). After the part (H) go
inside the position, put back the M8 HEX Nut and tighten it using M8 Spanner (11).
To install the complete set of (G) to the left and right side rail (C), you will need to use hardware 5 and 7 with Allen key
M5 (13).
To assemble part G, it is a must to make sure the hole go into the right position as shown in (NOTE). And before
tighten the screw, please make sure part G is in same alignment in between left and right side rail.
DO NOT use any power tools as this may damage the bed frame and will invalidate any claims.
Page 5 of 10
* Please insert the screw end to right hand side.
5 JCBB M8 x 40mm 8 pcs
7 M8 Flat Washer 8 pcs
11 M8 Spanner 1 pc
13 Allen Key M5 1 pc
A
B
Do Not Use Power Tools

2x
E
2x F
D
D
I
D
2x F
D
8
1
10
2
8
10
12
12
Step 4:
To assemble part D, it is a must to make sure the hole go into the right position as shown in (NOTE). And before tighten
the screw, please make sure part G is in same alignment in between left and right side of part G.
DO NOT use any power tools as this may damage the bed frame and will invalidate any claims.
Page 6 of 10
D
E
E
1 JCBC M6 x 45mm 8 pcs
2 JCBC M6 x 80mm 2 pcs
8 M6 Hex Nuts 10 pcs
10 M6 Spanner 1 pc
12 Allen Key M4 1 pc
Do Not Use Power Tools

6 JCBC M8 x 45mm 6 pcs
9 M8 Hex Nuts 6 pcs
11 M8 Spanner 1 pc
13 Allen Key M5 1 pc
G
2x
9
11
Step 5:
To assemble part D, it is a must to make sure the hole go into the right position as shown in (NOTE). And before tighten
the screw, please make sure part G is in same alignment in between left and right side of part G.
DO NOT use any power tools as this may damage the bed frame and will invalidate any claims.
Page 7 of 10
* Please insert the screw balance in the middle of the hole.
D
G
13
6
D
C
C
A
B
Do Not Use Power Tools

6 JCBC M8 x 45mm 6 pcs
9 M8 Hex Nuts 6 pcs
11 M8 Spanner 1 pc
13 Allen Key M5 1 pc
G
2x
9
11
Step 5:
To assemble part D, it is a must to make sure the hole go into the right position as shown in (NOTE). And before tighten
the screw, please make sure part G is in same alignment in between left and right side of part G.
DO NOT use any power tools as this may damage the bed frame and will invalidate any claims.
Page 8 of 10
* Please insert the screw balance in the middle of the hole.
D
G
13
6
D
C
C
A
B
Do Not Use Power Tools

B
A
K
Step 6:
To put the 2 X BOTTOM PANEL (K), you will need to slightly raise up the beds from the footboard (B) and slot in the
panel go direct to the headboard and continue the second pieces there after the first pieces was in right position.
WARNING:
Take care when assembling the base, assemble the ottoman as closed to its final position. The Ottoman has a
powerful mechanism and after assembly should only be closed and opened when the mattress is in place.
B
A
K
K
Page 9 of 10
C
C
COMPLETE

Page 10 of 10
General Care
Recommendations
Warning
Notes
.
When've correctly adjusted the centre support leg on this bed frame should be raised by 5mm from
the floor with added weight of the mattress and bedding.
This bed may fail if it is used on a wooden floor WITHOUT the use of non-slip pads on all the support
legs and bed posts.
If the bed is to be moved, carefully lift the bed frame rather than dragging to ensure that the centre
legs do not become twisted and buckle.