Happy Beds Prince User manual

Assembly Instructions
Prince Ottoman TV Bed
www.happybeds.co.uk
Important before assembly: .
Health & Safety:
.
Read these instructions carefully before assembling or using the product.
Please check the contents of the boxes before attempting to assemble this product. The instructions will
have a checklist of parts and fittings.
Assemble the product as close to its intended final location/room as possible.
This product or some parts of this product will be heavy. Please use an assistant when lifting.
Please keep small parts out of reach of children.
Always use on a level, even surface.
DO NOT jump on the product or any of its parts.
DO NOT use this product if any parts are missing, damaged or worn.
DO NOT use this product unless all fixings are secured.
Further instructions are on the following pages.
Please keep these instructions for future reference.
Page 1 of 14

Page 2 of 14
230829
1
2
9
10 x2
3
3
11
12
5
5
6
6
No Part List Qty Box
1 1 pc
2 1 pc
3 2 pcs
4
5 2 pcs
6 2 pcs
7a
Side rails
1 pc
7b
1 pc
14
No Part List Qty Box
12
2 pcs
3 pcs
Double
& King
Super King
13
1 pc
Headboard
Footboard
“U” shaped cross bar
Headboard feet
1
11
3 pcs
4
4
2
1 pc
2
2
3
2
2
2
2
Mattress base board support rail
Gas-lift mechanism
Gas-lift mechanism
Gas-lift pistons 2pcs
82
1 pc
94
Metal connection plates
15 2 pc 2
18
19
16 1 pc
3 pcs
3 pcs
1 pc
17
2
2
2
2
2 pcs
10 2
Mattress stoppers
Mattress base board
Mattress base board
Footboard feet
Fabric base cover
1 pc 2
4
7b
8
8
13
15 x 2
16
17
18
19
14 x3
Fabric hand strap
7a
Mains power lead
Remote control for TV lift
Cable clips
Cable ties

Page 3 of 14
No Qty Box
2 pcs
2 pcs
2
2
Hardware List
HARDWARE NEEDED FOR TV INSTALLATION (PACK B)
U
No Qty Box
Hardware List
1 pc
V
W
1 pc
2 pcs
2
2
2
2 pcs 2
TV Support Slide
X2 pcs 2
Bolt set
M8 x 25mm
Counter-sunk screw
set (M6x12mm)
Counter-sunk screw
set (M4x12mm)
Allen key (2.5mm)
Allen key (4mm)
Plastic spacer for fitting
TV (see Step 13 ii)
No Qty Box
4 pcs
8 pcs
24 pcs 2
Hardware List
HARDWARE NEEDED FOR BED ASSEMBLY (PACK A)
D
H
J
B
A
C
No Qty Box
Hardware List
E16 pcs
K
L
2 pcs
2 pcs
Hook bracket
Hook bracket
Bolt (M8x20mm)
Bolt (M8x65mm)
Bolt (M8x45mm)
Bolt (M6x35mm)
2
2
2
2
2
2
2
4 pcs 2
F 1 pc 2
Bolt (M8x35mm)
8 pcs
12 pcs
16 pcs
Double
& King
Super King
Allen key for M6 bolts
G 1 pc 2
Allen key for M8 bolts
Plastic spacer for lift
mechanism (7a & 7b)
Flanged M8 lock-nuts
M1 pc
Spanner for flanged
M8 lock-nuts 2
WARNING
TO AVOID ACCIDENTS
To access the storage area, the ottoman frame
MUST BE FULLY OPENED and then
FULLY CLOSED afterwards.
CAUTION
To be operated by ADULTS ONLY.
Keep children and pets away from the storage area.
Avoid trapping your fingers by using the handle
to lift & lower the base.
Only lift when the mattress is in place.
Ensure the ottoman support bar is secure when the
base is open.
Regularty air internal storage area and contents.
!
Note: Be very careful what you
store under the bed -the top of
an item, like a suitcase or a box
must not touch the slats or they
may be damaged. Maximum
storage height is 280mm .

Hook bracket
Hook bracket
Step 1:
Step 2:
Page 4 of 14
Bolts (M6x35mm)
D
DD
DD
K
x2
K
J
J
A x3
Headend
Footend
8 pcs F
1
2
1
6
2
5
5
5
6
6
3
Allen key for
M6 bolts 1 pc
Bolts (M8x20mm)
A 12 pcs
GAllen key for
M8 bolts 1 pc
J 2 pcs
2 pcs
K
A x3

B x4
E x4
H x4
H x4
1
1
1
7a
7b
Bolts (M8x65mm) Bolts (M8x35mm)
B 4 pcs
GAllen key for
M8 bolts 1 pc
E 4 pcs
8 pcs
H
Step 3a:
Step 3b:
Page 5 of 14
Plastic spacer for lift
mechanism (7a & 7b)
Bolts (M8x65mm) Bolts (M8x35mm)
B 4 pcs
GAllen key for
M8 bolts 1 pc
E 4 pcs
8 pcs
HPlastic spacer for lift
mechanism (7a & 7b)
Note: Please choose which side of the slat-frame to lift up to reach into the storage area
then depending which size of bed you have purchased.
2
2
B x4
H x4
7b
1
E x4
H x4
2
2
7a

1
2
3
3
Step 4:
Step 5:
Page 6 of 14
Bolts (M8x35mm)
E 12 pcs GAllen key for
M8 bolts 1 pc
Bolts (M8x45mm)
C 4 pcs E Allen key for
M8 bolts 1 pc
E x3
C x2
E x3
KK
J
K
J
J
3
3
3
4
4
Make certain the bed is
squared up as shown
in the diagram then
tighten all bed
assembly bolts 100%.

Step 6:
Step 7:
Page 7 of 14
Fit the fabric base cover (9) evenly
around the inside of the bed.
9
Connect the mains power lead
(17) to your wall socket - for
safety this must be an earthed
power supply.
Press the “UP” button
to raise the TV lift.
ii)
i)
19
16

Note: For illustration purposes only, TV connections may vary.
Tip:
Before fitting the TV, push cables through each
duct from the top choosing the best side to use
depending on where the connection ports are
on back of your TV.
Never cross cables from one side of the
footboard to the other unless cable is threaded
behind the TV supports, in front of the TV Lift.
5mm
Max TV Height
573mm
Height of TV is normally pre-set - follow this guide if it needs to be changed.
V
Step 11:
Step 12:
Page 8 of 14
TV Power Lead
supplied with your TV
W
ii. Loosen the two column adjustment bolts,
slide column so curved lid lifter is just
above the TV and re-tighten the two bolts.
iii. The upper part of each support (W) slides
to hold front of TV in place. Please follow
the instructions on how to correctly set
these supports in Step 14 iii.
i. Measure the height of the TV.
Add 5mm to it's height then
adjust the column to suit.

UU
X
X
V
V
Step 13:
Step 14:
Page 9 of 14
2 pcs
2 pcs
U
2 pcs
M8 x 25mm
Bolt set
Counter-sunk screw
set (M6x12mm)
Counter-sunk screw
set (M4x12mm)
1 pc
V
1 pc
Allen key (2.5mm)
Allen key (4mm)
If the TV is supplied with Vesa bolts and spacers, please use those in preference to those provided
ii.
iii.
Check the hardware supplied with the
television and if Vesa bolts and spacers
are supplied please use these to fit the TV.
i.
iv.
To adjust the two TV supports (W),
stand the TV in position and loosely
secure it to the bracket using the
hardware supplied. Each slider should
be set to just touch the front bezel. To
make sliding each support easier, lift
the TV slightly, above the support
being adjusted.
Once supports are set, lightly push
down In the top centre of the TV
and tighten the two Vesa bolts
100%, these should be in the centre
of the long holes as shown.
If hardware is not
supplied with the
TV, choose suitable
fittings from the TV
Kit
X2 pcs
Spacer for fitting to rear of
the TV. If no spacers are
supplied with the TV itself, please use
these two marked (X) making sure the
bolt length is correct. Fit them in the
position shown in Step 11 part ii.
It is important to fit them to allow more
clearance for the TV hinge system.
When spacers are provided it is
very important that these are fitted
in the correct place, fit between TV
& TV bracket as in this sketch.
These are needed to keep the TV
screen vertical.
TV BRACKET

Note: For illustration purposes only, TV connections may vary.
TV power lead
supplied with your TV Keep all leads tight, peel
off cover from cable clips
& adhere to back of TV.
Press the “DOWN” button
to lower the TV lift.
Step 15:
Step 16:
Page 10 of 14
17
18
KEEP ALL CABLES
TIGHT BY USING CLIPS
& TIES PROVIDED.

Step 15:
Step 16:
Page 11 of 14
Bolts (M8x45mm)
C8 pcs
12 pcs
Double
& King
Super King GAllen key for
M8 bolts 1 pc
13
13
13
13
13
13
11
11
12
12
11
12
C x4
C x4
C
A x2
A x2
C x4
C x4
C x4
Bolts (M8x20mm)
A 6 pcs G Allen key for
M8 bolts 1 pc
11
11
11
12
&
12
12
15
15
14 14
14

Step 15:
Step 16:
Page 12 of 14
A x3
L
L
SMALL GAP
L 4 pcs M 1 pc
Flanged M8 lock-nuts
for gas-lift piston Spanner for flanged
M8 lock-nuts
8
Bolts (M8x20mm)
A 6 pcs G Allen key for
M8 bolts 1 pc
11
11
10
12
12
&

Page 13 of 14
BASS CONTROL
Adjust the Bass attenuation - these buttons increase or decrease the lower
frequencies of the sound.
TREBLE CONTROL
Adjust the Treble attenuation - these buttons increase or decrease the higher
frequencies of the sound until the preferred sound level is achieved.
Note: if higher frequency sound is reduced, the volume of the sound appears
to be reduced too - this is normal.
MIN
VOL.
MAX
+
BASS +
TREB. +
TURN AMPLIFIER ON or OFF.
VOLUME CONTROL
Use --- + or - --- button to increase or decrease the volume.
Note that this control operates step by step and as it is adjusted, the blue LED
light bar follows each step until full volume is reached, then the blue lights are
all on.
SELECT OPTICAL or BLUETOOTH MODE.
Select the required mode by pressing OPT (Optical) to watch TV
or
Select BT (Bluetooth) to connect to your smart device to play music.
Pair your device in the normal way searching for -- 'MY BT'.
Two devices can pair with the system but each will need to disconnect to
allow the other to connect.
If device previously connected, system will immediately say PAIRED.
If not previously connected, system shall say PAIRING.
Note you cannot play films through the system from any BT device.
BT OPT
MODE
LIFT or LOWER THE TV.
Press once and TV will rise to it's upper working position. Power to the TV will
be connected automatically - operate the TV using it's Operation Guide.
Press once and TV Lift will stop.
Press once and TV will go down - as soon as the lower resting position is
reached power to the TV is switched off to prevent it overheating.
NOTE: BLUETOOTH WILL WORK NORMALLY WHEN TV IS UP OR DOWN.
ON OFF
1) Turn on the mains power to the TV Bed.
2) Press the Remote Control (RC) ON button for 2 seconds to synchronise
and prepare the system, system voice shall say 'Power On'.
3) When finished press the OFF button for 2 seconds.
The same blue LED light bar is used to show steps for all the following controls:
VOLUME, BASS & TREBLE.
This button switches on the torch.
BT OPT
MODE
MIN
+
VOL.
BASS
TREB.
MAX
+
+
ON OFF
These buttons are to control
the lights when fitted - they
are not fitted in this version of
your TV Bed.
MUTE
This button turns the sound o ff and back on again.

Page 14 of 14
80
170
830
30
350
310
L
W
H
www.happybeds.co.uk
General Care & Maintenance
Please dispose of all packaging safely.
Wipe clean with a slightly damp cloth.
Avoid the use of all household cleaners and abrasives.
Periodically check all screw & fixings to ensure they are secure.
When moving your product, carefully lift into place. Never drag or push the product across the floor as
this will cause damage to the joints. If the product is used on hard flooring, such as wood or laminated
floor, you must place some protection under the legs to stop the product from moving. If this is not
adhered to, it could result in failure to the product that will invalidate the warranty.
For more information on cleaning and product care visit:
https://www.happybeds.co.uk/help-and-advice
In the unlikely event that you have problems putting this product together or have damaged or
missing parts, please contact us by visiting:
https://www.happybeds.co.uk/customer-service
Notes
Technical Specifications
Overall Dimensions (LWH mm)
Internal Dimensions (LWH mm)
Double: 1900 x 1330 x 280
King : 2030 x 1480 x 280
Double : 2200 x 1380 x 1300
King: 2300 x 1530 x 1300
Super King: 2300 x 1830 x 1300
Super King: 2030 x 1780 x 280
Super King: 1000N
Ottoman Piston Strength
:gniK&elbuoD 900N
Floor to top of
the side rail
Floor to top of the
mattress base