Harbor Freight Tools Braun Quick Connect 56200 User manual

Visit our website at: http://www.harborfreight.com
Email our technical support at: [email protected]
Owner’s Manual & Safety Instructions
Save This Manual Keep this manual for the safety warnings and precautions, assembly,
operating, inspection, maintenance and cleaning procedures. Write the product’s serial number in the
back of the manual near the assembly diagram (or month and year of purchase if product has no number).
Keep this manual and the receipt in a safe and dry place for future reference. 19d
When unpacking, make sure that the product is intact
and undamaged. If any parts are missing or broken,
please call 1-888-866-5797 as soon as possible.
Copyright© 2019 by Harbor Freight Tools®. All rights reserved.
No portion of this manual or any artwork contained herein may be reproduced in
any shape or form without the express written consent of Harbor Freight Tools.
Diagrams within this manual may not be drawn proportionally. Due to continuing
improvements, actual product may differ slightly from the product described herein.
To ol s r eq ui r ed f o r as s em bl y a nd se rvice m a y not be i nc luded.
Read this material before using this product.
Failure to do so can result in serious injury.
SAVE THIS MANUAL.

Page 2 For technical questions, please call 1-888-866-5797. Item 56200
Specifications
Input Rating 5VDC, 1A
Battery 3.7V, Li-Ion
18650 type
Charge Time* 4 hr 45 min
*Note: Charge time will vary depending on the amp rating of the USB port the cord is attached to.
IMPORTANT SAFETY INFORMATION
To prevent serious injury, FIRE, and EXPLOSION:
1. Keep dry.
2. Only use included charging adaptors. Other
adaptors may damage tool or cause fire.
3. Do not submerge Light.
4. Do not operate in explosive atmospheres,
such as in the presence of flammable
liquids, gases, or dust.
5. People with pacemakers should consult their
physician(s) before use. Electromagnetic fields in
close proximity to heart pacemaker could cause
pacemaker interference or pacemaker failure.
6. Not a toy. Keep out of reach of children.
7. Contains Li-Ion battery. Battery must be
recycled or disposed of properly. Do not open,
crush, heat above 140° F or incinerate.

Page 3For technical questions, please call 1-888-866-5797.Item 56200
Charging Instructions
Read the ENTIRE IMPORTANT SAFETY INFORMATION section at the beginning of this document
including all text under subheadings therein before set up or use of this product.
1. Insert one end of the USB Charging
Cable into the Charging Jack on the side
of the Handle, under the cover.
Charging
Jack
USB
Charging
Cable
Handle
Base
Power
Switch
(other side)
2. Plug the other end of the USB Charging
Cable into a powered USB port.
3. The Charging Indicator on the Power Switch will
turn Red during charging. When charging is done,
it will turn Green. Unplug the Charging Cable.
NOTICE: Do not leave the Battery in a
discharged state. Charge the Battery every 3 months
if the Light is not in use. This will keep the Battery
from wearing down and add to its life. Do not
charge the Light at temperatures below 40° F.
Battery Replacement
1. Unscrew the Base of the Handle.
2. Remove the old battery.
3. Insert a new battery into the
Handle, positive end first.
4. Screw the Base onto the Handle until tight.
5. Contains Li-Ion battery. Battery must be
recycled or disposed of properly. Do not open,
crush, heat above 140° F or incinerate.

Page 4 For technical questions, please call 1-888-866-5797. Item 56200
Operation Instructions
Read the ENTIRE IMPORTANT SAFETY INFORMATION section at the beginning of this document
including all text under subheadings therein before set up or use of this product.
NOTE: Before using the Light for the
first time, fully charge the Battery.
1. Connect one of three Light attachments
to the Handle: Flashlight, Inspection
Light or Flexible Slim Light.
2. To connect Light attachment:
a. Insert the attachment inside the Locking
Collar until it clips firmly in place.
Locking
Collar Power
Switch
b. To remove attachment, pull Locking
Collar back to release the attachment.
3. Once a Light is connected to the Handle,
press the Power Switch to turn on the Light.
4. Press the Power Switch again to
switch to economy mode.
5. Press the Power Switch a third
time to turn the Light off.
6. The Magnetic Swivel Hook can
be used in two ways:
a. Place the Light into the Hook’s clip and
adjust the clip angle as desired.
b. Place the bottom of Light’s Base onto the Hook’s
magnetic plate, adhering the Hook to the Light.
7. When finished using the Light, store
indoors away from children.

Page 5For technical questions, please call 1-888-866-5797.Item 56200
PLEASE READ THE FOLLOWING CAREFULLY
THE MANUFACTURER AND/OR DISTRIBUTOR HAS PROVIDED THE PARTS LIST AND ASSEMBLY DIAGRAM
IN THIS MANUAL AS A REFERENCE TOOL ONLY. NEITHER THE MANUFACTURER OR DISTRIBUTOR
MAKES ANY REPRESENTATION OR WARRANTY OF ANY KIND TO THE BUYER THAT HE OR SHE IS
QUALIFIED TO MAKE ANY REPAIRS TO THE PRODUCT, OR THAT HE OR SHE IS QUALIFIED TO REPLACE
ANY PARTS OF THE PRODUCT. IN FACT, THE MANUFACTURER AND/OR DISTRIBUTOR EXPRESSLY
STATES THAT ALL REPAIRS AND PARTS REPLACEMENTS SHOULD BE UNDERTAKEN BY CERTIFIED AND
LICENSED TECHNICIANS, AND NOT BY THE BUYER. THE BUYER ASSUMES ALL RISK AND LIABILITY
ARISING OUT OF HIS OR HER REPAIRS TO THE ORIGINAL PRODUCT OR REPLACEMENT PARTS
THERETO, OR ARISING OUT OF HIS OR HER INSTALLATION OF REPLACEMENT PARTS THERETO.

Page 6 For technical questions, please call 1-888-866-5797. Item 56200
Parts List and Diagram
Parts List
Record Product’s Serial Number Here:
Note: If product has no serial number, record month and year of purchase instead.
Note: Some parts are listed and shown for illustration purposes only,
and are not available individually as replacement parts.
Part Description Qty.
1 Handle 1
2 Flashlight 1
3 Inspection Light 1
4 Flexible Slim Light 1
Part Description Qty.
5Li-Ion Battery, 3.7V 2600 mA 1
6 USB Charging Cable 1
7 Magnetic 180° Swivel Hook 1
8 Nylon Bag 1

Page 7For technical questions, please call 1-888-866-5797.Item 56200
Assembly
12
3
4
5
6
7
8

26541 Agoura Road • Calabasas, CA 91302 • 1-888-866-5797
Limited 90 Day Warranty
Harbor Freight Tools Co. makes every effort to assure that its products meet high quality and durability
standards, and warrants to the original purchaser that this product is free from defects in materials
and workmanship for the period of 90 days from the date of purchase. This warranty does not apply to
damage due directly or indirectly, to misuse, abuse, negligence or accidents, repairs or alterations outside
our facilities, criminal activity, improper installation, normal wear and tear, or to lack of maintenance.
We shall in no event be liable for death, injuries to persons or property, or for incidental, contingent,
special or consequential damages arising from the use of our product. Some states do not allow the
exclusion or limitation of incidental or consequential damages, so the above limitation of exclusion
may not apply to you. THIS WARRANTY IS EXPRESSLY IN LIEU OF ALL OTHER WARRANTIES,
EXPRESS OR IMPLIED, INCLUDING THE WARRANTIES OF MERCHANTABILITY AND FITNESS.
To take advantage of this warranty, the product or part must be returned to us with transportation charges
prepaid. Proof of purchase date and an explanation of the complaint must accompany the merchandise.
If our inspection verifies the defect, we will either repair or replace the product at our election or we may
elect to refund the purchase price if we cannot readily and quickly provide you with a replacement. We will
return repaired products at our expense, but if we determine there is no defect, or that the defect resulted
from causes not within the scope of our warranty, then you must bear the cost of returning the product.
This warranty gives you specific legal rights and you may also have other rights which vary from state to state.