Harbor Freight Tools Badland 57607 Assembly instructions

57607
Visit our website at: http://www.harborfreight.com
Email our technical support at: [email protected]
Owner’s Manual & Safety Instructions
Save This Manual Keep this manual for the safety warnings and precautions, assembly,
operating, inspection, maintenance and cleaning procedures. Write the product’s serial number in the
back of the manual near the assembly diagram (or month and year of purchase if product has no number).
Keep this manual and the receipt in a safe and dry place for future reference. 21g
When unpacking, make sure that the product is intact
and undamaged. If any parts are missing or broken,
please call 1-888-866-5797 as soon as possible.
Copyright©2020 by Harbor Freight Tools®. All rights reserved.
No portion of this manual or any artwork contained herein may be reproduced in
any shape or form without the express written consent of Harbor Freight Tools.
Diagrams within this manual may not be drawn proportionally. Due to continuing
improvements, actual product may differ slightly from the product described herein.
Tools required for assembly and service ma y n o t b e i n c l u d e d .
Read this material before using this product.
Failure to do so can result in serious injury.
SAVE THIS MANUAL.

Page 2 For technical questions, please call 1-888-866-5797. Item 57607
Important Safety Information
TO PREVENT SERIOUS INJURY:
1. Do not exceed 12,000 lb pull capacity.
Be aware of dynamic loading!
Sudden load movement may
briefly create excess load
causing product failure.
Capacity limited by hitch mounted on.
2. Obey DOT and local regulations
for use on public roads.
3. Route cable through fairlead slot
and pull straight back only.
4. Wear ANSI-approved safety goggles and
heavy-duty work gloves during setup.
5. Secure before use.
6. Inspect before every use;
do not use if parts loose or damaged.
7. Use as intended only.
8. Read winch manual and manual for hitch
receiver this is mounted in before setup.
9. Assemble only according to these
instructions. Improper assembly
can create hazards.
10. Keep assembly area clean and well lit.
11. Keep bystanders out of the
area during assembly.
12. Do not assemble when tired
or when under the influence
of drugs or medication.
13. Do not drill new holes to attach winch
to mount or weld winch to mount.
14. Weight capacity and other product
capabilities apply to properly and
completely assembled product only.
15. This product is not a toy. Do not allow
children to play with or near this item.
16. Maintain product labels and nameplates.
These carry important safety information.
If unreadable or missing, contact
Harbor Freight Tools for a replacement.

Page 3For technical questions, please call 1-888-866-5797.Item 57607
Assembly Instructions
Assembling the Winch Hitch Mount
1. Assemble the two Handles (1) to the
Winch Hitch Mount using included
hardware: Eight Bolts (5), Washers (6),
and Nuts (7). Tighten securely.
Handle (1)
Handle (1)
Bolt (5)
Washer (6)
Nut (7)
Mount Plate
Mount (3)
Connecting the Winch Hitch Mount to Hitch
1. Insert the Mount (3) into the
receiver on the hitch.
2. Connect by inserting the Hitch Pin (2)
through the holes in the Mount (3) and
Hitch Receiver. Secure with R-Clip (4).
R-Clip (4)
Hitch Pin (2)
Mount (3)
Hitch
Receiver
Hitch

Page 4 For technical questions, please call 1-888-866-5797. Item 57607
Attaching Winch to Winch Hitch Mount
1. Attach Winch (sold separately) to the
Winch Hitch Mount. Fasten with four
bolts and nuts (sold separately).
2. Attach Roller Fairlead (sold separately)
to the side of the Mount Plate.
3. Pull in the Sliding Blocks (8), if needed.
4. Fasten with bolts and nuts (sold
separately). Tighten securely.
Winch Hitch
Mount
Winch
Mount Plate
Roller Fairlead
Sliding Blocks (8)
Roller Fairlead

Page 5For technical questions, please call 1-888-866-5797.Item 57607
PLEASE READ THE FOLLOWING CAREFULLY
THE MANUFACTURER AND/OR DISTRIBUTOR HAS PROVIDED THE DIAGRAM IN THIS
DOCUMENT AS A REFERENCE TOOL ONLY. NEITHER THE MANUFACTURER OR DISTRIBUTOR
MAKES ANY REPRESENTATION OR WARRANTY OF ANY KIND TO THE BUYER THAT HE
OR SHE IS QUALIFIED TO MAKE ANY REPAIRS TO THE PRODUCT, OR THAT HE OR SHE IS
QUALIFIED TO REPLACE ANY PARTS OF THE PRODUCT. IN FACT, THE MANUFACTURER AND/
OR DISTRIBUTOR EXPRESSLY STATES THAT ALL REPAIRS AND PARTS REPLACEMENTS
SHOULD BE UNDERTAKEN BY CERTIFIED AND LICENSED TECHNICIANS, AND NOT BY
THE BUYER. THE BUYER ASSUMES ALL RISK AND LIABILITY ARISING OUT OF HIS OR
HER REPAIRS TO THE ORIGINAL PRODUCT OR REPLACEMENT PARTS THERETO, OR
ARISING OUT OF HIS OR HER INSTALLATION OF REPLACEMENT PARTS THERETO.

Page 6 For technical questions, please call 1-888-866-5797. Item 57607
Parts List and Diagram
Parts List
Part Description Qty
1 Handle 2
2 Hitch Pin 1
3 Mount 1
4 R-Clip 1
5 Bolt 8
6 Washer 8
7 Nut 8
8 Sliding Block 2
Record Serial Number Here:
Note: If product has no serial number, record
month and year of purchase instead.
Note: Some parts are listed and shown
for illustration purposes only, and are
not available individually as replacement
parts. Specify UPC 193175418722
when ordering parts.

Page 7For technical questions, please call 1-888-866-5797.Item 57607
Assembly Diagram

Limited 90 Day Warranty
Harbor Freight Tools Co. makes every effort to assure that its products meet high quality and durability
standards, and warrants to the original purchaser that this product is free from defects in materials
and workmanship for the period of 90 days from the date of purchase. This warranty does not apply to
damage due directly or indirectly, to misuse, abuse, negligence or accidents, repairs or alterations outside
our facilities, criminal activity, improper installation, normal wear and tear, or to lack of maintenance.
We shall in no event be liable for death, injuries to persons or property, or for incidental, contingent,
special or consequential damages arising from the use of our product. Some states do not allow the
exclusion or limitation of incidental or consequential damages, so the above limitation of exclusion
may not apply to you. THIS WARRANTY IS EXPRESSLY IN LIEU OF ALL OTHER WARRANTIES,
EXPRESS OR IMPLIED, INCLUDING THE WARRANTIES OF MERCHANTABILITY AND FITNESS.
To take advantage of this warranty, the product or part must be returned to us with transportation charges
prepaid. Proof of purchase date and an explanation of the complaint must accompany the merchandise.
If our inspection verifies the defect, we will either repair or replace the product at our election or we may
elect to refund the purchase price if we cannot readily and quickly provide you with a replacement. We will
return repaired products at our expense, but if we determine there is no defect, or that the defect resulted
from causes not within the scope of our warranty, then you must bear the cost of returning the product.
This warranty gives you specific legal rights and you may also
have other rights which vary from state to state.
26541 Agoura Road • Calabasas, CA 91302 • 1-888-866-5797