Harman JBL BAR 300 User manual

BAR 300
OWNER’S MANUAL

22
IMPORTANT SAFETY INSTRUCTIONS
Verify Line Voltage Before Use
The JBL BAR 300 (soundbar) has been designed for use with
100-240 volt, 50/60 Hz AC current. Connection to a line voltage
other than that for which your product is intended can create
a safety and re hazard and may damage the unit. If you have
any questions about the voltage requirements for your specic
model or about the line voltage in your area, contact your retailer
or customer service representative before plugging the unit into
a wall outlet.
Do Not Use Extension Cords
To avoid safety hazards, use only the power cord supplied
with your unit. We do not recommend that extension cords be
used with this product. As with all electrical devices, do not run
power cords under rugs or carpets, or place heavy objects on
them. Damaged power cords should be replaced immediately
by an authorized service center with a cord that meets factory
specications.
Handle the AC Power Cord Gently
When disconnecting the power cord from an AC outlet, always
pull the plug; never pull the cord. If you do not intend to use this
speaker for any considerable length of time, disconnect the plug
from the AC outlet.
Do Not Open the Cabinet
There are no user-serviceable components inside this product.
Opening the cabinet may present a shock hazard, and any
modication to the product will void your warranty. If water
accidentally falls inside the unit, disconnect it from the AC power
source immediately, and consult an authorized service center.

www.jbl.com
English
33
TABLE OF CONTENTS
IMPORTANT SAFETY INSTRUCTIONS 2
1. INTRODUCTION 4
2. WHAT’S IN THE BOX 5
3. PRODUCT OVERVIEW 6
3.1 SOUNDBAR 6
3.2 REMOTE CONTROL 7
4. PLACE 8
4.1 DESKTOP PLACEMENT 8
4.2 WALL-MOUNTING 8
5. CONNECT 9
5.1 CONNECTION WITH YOUR TV AND DIGITAL DEVICES 9
5.2 BLUETOOTH CONNECTION 11
5.3 CONNECTION WITH YOUR HOME NETWORK 11
6. SETUP 12
6.1 CONNECT POWER 12
6.2 3D SURROUND SOUND 13
7. PLAY 14
7.1 POWER-ON/AUTO STANDBY/AUTO WAKEUP 14
7.2 PLAY FROM THE TV SOURCE 15
7.3 PLAY FROM THE HDMI IN SOURCE 15
7.4 PLAY FROM THE BLUETOOTH SOURCE 16
7.5 PLAY THROUGH THE JBL ONE APP 16
7.6 PLAY THROUGH CHROMECAST BUILT-IN 17
7.7 PLAY THROUGH AIRPLAY 17
7.8 PLAY THROUGH AMAZON MUSIC 17
7.9 MULTI-ROOM PLAYBACK 18
8. SOUND SETTINGS 19
8.1 AUDIO SYNC 19
8.2 SMART MODE 19
8.3 PUREVOICE DIALOGUE ENHANCEMENT
TECHNOLOGY 19
9. RESTORE FACTORY SETTINGS 20
10. SOFTWARE UPDATE 20
11. PRODUCT SPECIFICATIONS 21
12. TROUBLESHOOTING 22
13. TRADEMARKS 24
14. OPEN SOURCE LICENSE NOTICE 25

44
1. INTRODUCTION
Thank you for purchasing the JBL BAR 300 (soundbar) which
is designed to bring an extraordinary 3D sound experience to
your home entertainment system. We encourage you to take a
few minutes to read through this manual, which describes the
product and includes step-by-step instructions for setting up
and getting started.
To make the most of product features and support, you may
need to update the product software through the Internet
or the USB connector in the future. Refer to the software
update section in this manual to ensure that your product
has the latest software.
Designs and specications are subject to change without notice.
If you have any questions about the soundbar, installation or
operation, please contact your retailer or customer service
representative, or visit our website: www.jbl.com.
JBL One app
With the JBL One app, you can
• easily complete product setup;
• connect *music streaming services;
• discover new music with integrated music services;
• use one button to access your preset playlist and speaker
settings;
• access software updates when they are available.
JBL One
JBL One
For more information, see “5.3 Connection with your home
network” and “7.5 Play through the JBL One app”.
NOTES:
– *Subscription may be needed and not provided by the JBL One app.

www.jbl.com
English
55
2. WHAT’S IN THE BOX
Unpack the box carefully and ensure that the following parts are
included. If any part is damaged or missing, do not use it and
contact your retailer or customer service representative.
Soundbar
Remote control (with 2 AAA batteries)
(AAA)
Power cord*
* Power cord quantity and plug type vary region.
HDMI cable (1.2 m/3.9 ft.)
Wall-mounting kit
x 2
x 2
x 2
x 2
x 2
Product information & wall-mounting template

66
3. PRODUCT OVERVIEW
3.1 Soundbar
3.1.1 Controls
5
34 12
1) (Source)
• Switch on
• Select a sound source: TV (default, for audio input
from TV connection where the HDMI OUT (TV ARC/
TV eARC) connector is prioritized over the OPTICAL
connector), Bluetooth or HDMI IN
2) /(Volume)
• Switch on
• Decrease or increase the volume
• Press and hold to decrease or increase the volume
continuously
• Press the two buttons together to mute or unmute
3) Status indicator
System:
Regular flashing (white) System startup
Fast flashing (white) Software updating in progress
Solid (amber) Restoring factory settings
Network connection:
Slow flashing (white) Entering Wi-Fi setup mode, or
network disconnected
Solid (green) Soundbar discovered by the JBL
One app
Solid (white) Network connected
Solid (yellow) Weak Wi-Fi connection
4) Microphone
• For sound calibration
5) Status display
3.1.2 Rear connectors
1 2 3 4
5
1) POWER
• Connect to power (with the supplied power cord)
2) USB
• USB connector for software update
• Connect to a USB storage device for MP3 le playback
(for US version only)
3) ETHERNET
• Connect to your home network through an Ethernet
cable
4) HDMI IN
• Connect to the HDMI output on your digital device
5) TV connectors
HDMI OUT (TV ARC/ TV eARC)
• Connect to the HDMI ARC / HDMI eARC input on
your TV
OPTICAL
• Connect to the optical output on your TV or digital device

www.jbl.com
English
77
3.2 Remote control
8
7
6
5
4
1
2
3
1)
• Switch on or to standby
2) Source selectors
TV
• Select the TV source (default, for audio input from TV
connection where the HDMI OUT (TV ARC/ TV eARC)
connector is prioritized over the OPTICAL connector)
(Bluetooth)
• Select the Bluetooth source
• Press and hold to connect a Bluetooth device
HDMI
• Select the HDMI IN source
3) Sound effect buttons
• Switch the virtual Dolby Atmos®sound effects on or off
(Default: on)
• Select the bass level for subwoofer: 1/2/3 (default)/4/5
4) CALIBR
• Press to start sound calibration
5) (Moment)
• Press to directly access your music playlist and speaker
settings that you have personalized in the JBL One app
6) (Playback controls during the music streaming over JBL
One app, Chromecast built-in™, AirPlay, Alexa or Bluetooth)
• Single press: Pause or resume playback
• Double press: Next track
• Triple press: Previous track
7) /
• Increase or decrease the volume
• Press and hold to increase or decrease the volume
continuously
8) (Mute)
• Mute/unmute
3.2.1 App-enabled control
With the JBL One app on your Android and iOS device, you can
do the following:
• Wi-Fi setup;
• Audio calibration & demo;
• Personalize audio settings;
• Manage and control device;
• Music service integration;
• Additional features.

88
4. PLACE
4.1 Desktop placement
Place the soundbar on a at and stable surface.
2.5-3.0 m / 8.2-9.8 ft
> 4 m / 13 ft
>5cm / 2”
NOTES:
– The power cord shall be properly connected to power.
–Do not place any objects on the top of the soundbar.
4.2 Wall-mounting
1
540 mm/21.26’’
1a)
1b)
1c)
> 50 mm/2’’
≤8 mm/0.31"
4 mm/0.16"
≥30 mm/1.18"
2 3
44
1. Preparation:
a) With a minimum distance of 2” (50mm) from your TV, stick
the supplied wall-mounting template to a wall by using
adhesive tapes.
b) Use your ballpen tip to mark the screw holder location.
Remove the template.
c) On the marked location, drill a 4 mm/0.16” hole.
2. Install the support for wall-mounting bracket.
3. With the screw, fasten the wall-mounting bracket onto the
bottom of the soundbar.
4. Mount the soundbar.
NOTES:
– Make sure that the wall can support the weight of the soundbar.
–Install on a vertical wall only.
–Avoid a location under high temperature or humidity.
–Before wall-mounting, make sure that cables can be properly
connected between the soundbar and external devices.
–Before wall-mounting, make sure that the soundbar is unplugged
from power. Otherwise, it may cause an electric shock.

www.jbl.com
English
99
5. CONNECT
5.1 Connection with your TV and digital
devices
For audio playback through the soundbar, connect the soundbar
with your TV through the supplied HDMI cable or an optical cable
(sold separately).
An HDMI connection supports digital audio and video with a
single connection. HDMI connectivity is the best option for your
soundbar.
5.1.1 TV (HDMI ARC / eARC)
(Recommended connection for the best Dolby Atmos experience)
HDMI IN
HDMI (ARC)
HDMI OUT
(TV ARC/TV eARC)
HDMI OUT
*
HDMI IN
1. Connect the soundbar with the HDMI IN (ARC) connector on
your TV by using the supplied HDMI cable.
• On your TV, check that HDMI-CEC and HDMI ARC have
been enabled. Refer to the owner’s manual of your TV for
more information.
2. Use an HDMI cable (V2.0 or later) to connect the soundbar
with your digital device, such as a set-top box, DVD/Blu-ray
player or game console.
• On your digital device, check that HDMI-CEC has been
enabled. Refer to the owner’s manual of your digital
device for more information.
• On your digital device, select “Bitstream” or “Raw data”
in the audio output settings for the best Dolby Atmos
experience.
3. To play audio from the digital device connected to the
soundbar, select HDMI on the remote control.
NOTES:
–If your TV does not support HDMI eARC, make sure that you
connect your digital device through the HDMI IN connector on
the soundbar instead of your TV. Otherwise, the Dolby Atmos
information cannot pass through the HDMI (ARC) connectors from
the TV to the soundbar.

1010
5.1.2 TV (HDMI eARC)
HDMI OUT
(TV ARC/TV eARC)
HDMI OUT
*
HDMI (eARC)
HDMI IN
TV
1. Connect the soundbar with the HDMI IN (eARC) connector
on your TV by using the supplied HDMI cable.
• On your TV, check that HDMI-CEC and HDMI eARC have
been enabled. Refer to the owner’s manual of your TV for
more information.
2. Use an HDMI cable (eARC compatible, V2.0 or later) to connect
your TV with your digital device, such as a streaming device,
set-top box, DVD/Blu-ray player or game console.
• On your digital device, check that HDMI-CEC has been
enabled. Refer to the owner’s manual of your digital
device for more information.
• On your TV and digital device, select “Bitstream” or “Raw
data” in the audio output settings for the best Dolby
Atmos experience.
3. To play audio from the digital device connected to your TV,
select TV on the remote control.
5.1.3 OPTICAL
HDMI OUT
*
OPTICAL
HDMI IN
OPTICAL
TV
NOTES:
–With the Virtual Dolby Atmos design, the Dolby surround upmixer
of the soundbar can expand the legacy channel-based audio of
Dolby Digital format, including 5.1 and 7.1 content, and provide an
immersive 3D Atmos experience.
1. Connect the soundbar with your TV by using an optical cable.
2. Use an HDMI cable (V2.0 or later) to connect your TV with your
digital device, such as a streaming device, set-top box, DVD/
Blu-ray player or game console.
3. To play audio through the optical cable, select TV on the
remote control.
NOTES:
–* The HDMI cable (for digital device connection) and the optical cable
are sold separately.
–Full compatibility with all HDMI-CEC devices is not guaranteed.
–When both HDMI ARC and optical cables are connected to the
soundbar for audio input from TV connection, the HDMI ARC
connection is prioritized.