Harman XXV User manual
Harman® • XXV Installation Manual_R31 • 2004 -___ • 11/1513-90-00684i
Model(s):
XXV Freestanding Pellet Stove
Installation Manual
Installation and Appliance Setup
INSTALLER: Leave this manual with party responsible for use and operation.
OWNER: Retain this manual for future reference.
NOTICE: SAVE THESE INSTRUCTIONS
Please read this entire manual before
installation and use of this pellet fuel-
burning room heater.
Failure to follow these instructions could
result in property damage, bodily injury
or even death.
Hot glass will cause burns.
High temperatures may ignite clothing or other
HOT SURFACES!
NOTE
WARNING
WARNING
CAUTION
!
CAUTION
!
Harman® • XXV Installation Manual_R31 • 2004 -___ • 11/1523-90-00684i
TABLE OF CONTENTS
3
4
4
2 Getting Started
6
7
7
3 Framing and Clearances
8
9
4 Termination Location and Vent Information
11
16
18
19
19
19
21
21
5 Appliance Setup
22
22
22
23
23
6 Reference Materials
24
= Contains updated information
Safety Alert Key:
• DANGER!
• WARNING!
• CAUTION!
• NOTICE:
!
Harman® • XXV Installation Manual_R31 • 2004 -___ • 11/1533-90-00684i
Installation Standard Work Checklist
ATTENTION INSTALLER:
Follow this Standard Work Checklist
Customer: ________________________________ Date Installed: __________________________
Lot/Address: ________________________________ Location of Stove: __________________________
________________________________ Installer: __________________________
Model: ________________________________ Dealer/Distributer Ph # __________________________
Serial Number: __________________________
!
WARNING! Risk of Fire or Explosion! Failure to install appliance to these instructions can lead
Appliance Install YES IF NO, WHY?
Venting/Chimney Section 4 (Pg. 10-19)
Electrical Section 1 (Pg. 4)
Appliance Setup Section 5 (Pg. 20-21)
Harman® • XXV Installation Manual_R31 • 2004 -___ • 11/1543-90-00684i
NOTE:
the ASTM E1509-2004, ULC-S628-93, ULC/ORD-C-
1482-M1990, (UM) 84-HUD.
B. Mobile Home Approved
1
MODEL:
LABORATORY:
REPORT NO.
TYPE:
STANDARD(s):
ELECTRICAL
RATING
GLASS
SPECIFICATIONS
The XXV
T H E S T R U C T U R A L I N T E G R I T Y O F T H E
MANUFACTURED HOME FLOOR, WALL, AND
CEILING/ROOF MUST BE MAINTAINED.
DO NOT INSTALL IN SLEEPING ROOM.
WARNING
!
Harman® • XXV Installation Manual_R31 • 2004 -___ • 11/153-90-00684i
NOTE:
F. Electrical Codes
NOTE: Some generator or battery back-up systems may
not be compatible with the micro-processor electronics
WARNING! Risk of Fire! Hearth & Home Technologies
disclaims any responsibility for, and the warranty and agency
listing will be voided by the below actions.
DO NOT:
• Install or operate damaged appliance
• Modify appliance
• Install other than as instructed by Hearth & Home
Technologies
• Operate the appliance without fully assembling all
components
• Install any component not approved by Hearth &
Home Technologies
• Install parts or components not Listed or approved.
• Disable safety switches
Improper installation, adjustment, alteration, service or
maintenance can cause injury or property damage.
installer, service agency or your dealer.
during EPA emissions test.
during EPA emissions test.
and the burn rates from the low and high EPA tests.
****Based on the maximum feed rate per hour multiplied by
approximately 8,600 BTU’s which is the average BTU’s from
a pound of pellets.
ASTM E 136,
Standard Test Method for Behavior of Materials in
a Vertical Tube Furnace at 750° C and UL763
***EPA BTU Output:
****BTU Input
Vent Size:
Hopper Capacity:
Fuel
Harman® • XXV Installation Manual_R31 • 2004 -___ • 11/1563-90-00684i
A
.
Design and Installation Considerations
1. Appliance Location
Notice: Check building codes prior to installation.
Marginal Location:
Marginal Location:
Figure 2.1
2 Getting Started
• Air Conditioner
NOTICE: Locating the appliance in a location of considerable
air movement can cause intermittent smoke spillage from
appliance. Do not locate appliance near:
• Frequently open doors
• Central heat outlets or returns
Harman® • XXV Installation Manual_R31 • 2004 -___ • 11/1573-90-00684i
B. Tools And Supplies Needed
Tools and building supplies normally required for
installation, unless installing into an existing masonry
C. Inspect Appliance and Components
• Read all of the instructions before starting the
installation. Follow these instructions carefully
during the installation to ensure maximum safety
WARNING
!
Risk of Fire, Explosion or Electric Shock! DO NOT use
and to replace any part of the control system which
Do NOT
WARNING
!
RISK OF FIRE OR EXPLOSION! Damaged parts
DO NOT install damaged,
incomplete or substitute components. Keep appliance
dry.
May also need:
Harman® • XXV Installation Manual_R31 • 2004 -___ • 11/1583-90-00684i
3 Clearances
Figure 3.1
A. Appliance Dimension Diagram
28-7/16”
722 mm
31-1/8”
791 mm
29-7/16”
748 mm
14-3/4””
375 mm
4-1/16””
103 mm
8-5/8””
219 mm
12-7/16””
316 mm
Outside Air
Intake
Harman® • XXV Installation Manual_R31 • 2004 -___ • 11/1593-90-00684i
B. Clearances to Combustibles
Figure 3.2
Floor Protection
12"/ 305mm
3"/ 76mm
Floor Protection
6.25"
159mm
6.25"
159mm
CAUTION
!
THIS APPLIANCE MUST BE VENTED TO THE OUTSIDE.
WARNING
!
RISK OF FIRE OR BURNS! Provide adequate
clearance around air openings and for service
Due to high temperatures, the appliance should
draperies.
Notice:
to individual design preference.
Harman® • XXV Installation Manual_R31 • 2004 -___ • 11/15 3-90-00684i
C. Floor Protection
NOTE for Canadian installation only:
space heater
requirements ONLY if the user agrees to completely
shut-down the appliance, and allow it to cool to where
door or ash door.
Floor protector minimum: 36” X 36” (914mm X 914mm)
D. Mobile Home Installation
•
DO NOT MIX COMPONENTS FROM
DIFFERENT MANUFACTURERS.
Floor Protection KJ
Canada
L
J
USA
40”
40”
as they satisfy the measurement requirements shown
hearth pad is 40” x 40” (USA ONLY). This also allows the
NOTE:
Floor Protection
Requirements US Canada
J
K
L
Harman® • XXV Installation Manual_R31 • 2004 -___ • 11/1511 3-90-00684i
4 Termination Location and Vent Information
A. Vent Termination Minimum Clearances
Figure 4.1
Figure 4.2
to
Combustibles
to Combustibles
INSTALL VENT AT CLEARANCES SPECIFIED BY THE
VENT MANUFACTURER
#1 Preferred method (Figure 4.1)
Do not place joints within wall pass-through.
3 Ft.
to
Combustibles
3 Ft.
to Combustibles
#2 Preferred method (Figure 4.2)
termination is at least 12” above grade. The outlet must also
be 1 foot from the house/building.
Do not place joints within wall pass-through.
CAUTION
!
KEEP COMBUSTIBLE MATERIALS (SUCH AS GRASS,
LEAVES, ETC.) AT LEAST 3 FEET AWAY FROM THE
FLUE OUTLET ON THE OUTSIDE OF THE BUILDING.
DO NOT USE MAKESHIFT COMPROMISES WHEN
INSTALLING THIS APPLIANCE. DAMAGE AND/OR
INJURY MAY RESULT.
CAUTION
!
WARNING
!
THE CHIMNEY AND CONNECTOR MUST BE
MAINTAINED IN GOOD CONDITION AND KEPT CLEAN.
Harman® • XXV Installation Manual_R31 • 2004 -___ • 11/1512 3-90-00684i
Figure 4.3
Figure 4.4
#3 Installing into an existing chimney (Figure 4.3)
(Figure 4.4)
Harman® • XXV Installation Manual_R31 • 2004 -___ • 11/1513 3-90-00684i
(Figure
4.5) w/Full Liner
#6 Installing into an existing chimney (Figure 4.6) w/Full liner
Figure 4.5
Figure 4.6
4"/102mm
18"/457mm
Optional Top Vent Pipe Clearances
6"/152mm
Harman® • XXV Installation Manual_R31 • 2004 -___ • 11/1514 3-90-00684i
PL vent manufacturer's
restop spacer and support
1" MIN.
No insulation or other
combustible materials
are allowed within 1"
of the PL vent pipe.
ashing
storm collar
1" MIN.
1" MIN.
12" MIN
1” MIN.
12"
min. above ground level
#7 Installing through the ceiling
Do not place joints within wall pass-through.
12"
min. wall to outlet
36"
min. clearance to any
combustable material
Figure 4.7 Figure 4.8
Figure 4.9
Harman® • XXV Installation Manual_R31 • 2004 -___ • 11/15 3-90-00684i
B. Chimney Diagram
V=Vent Terminal A=Air Supply Inlet =Area where termination is not permitted
Door
Sidewalk
Fixed
Closed
Openable
Openable Fixed
Closed
Inside Corner
Detail
Porch or
Openable
Deck
or Fixed
Requirements for Terminating the Venting
Figure 4.10
with outside air installed, 6 feet
(B. also)
NOTE: The clearance to vegetation and other exterior
combustibles such as mulch is 36” as measured from
the center of the outlet or cap. This 36” radius continues
to grade or a minimum of 7 feet below the outlet.
See NFPA 211 for more installation clearance reductions when
using outside air.
NOTE: Where passage through a wall, or partition of
combustible construction is desired, the installation
shall conform to CAN/CSA-B365. (if in Canada)
WARNING
!
Venting terminals must not be recessed into a wall
or siding.
stops should be used when venting through combustible
materials.
Always take into consideration the effect the prevailing
wind direction or other wind currents will cause with
In addition, the following must be observed:
with outside air installed, 9”
to side and below
Harman® • XXV Installation Manual_R31 • 2004 -___ • 11/1516 3-90-00684i
C. Venting & Use of Elbows
+= Positive static pressure
= Negative static pressure
+
+
-
-
Figure 4.11
Equivalent Vent Length: The equivalent vent length for
common pellet vent components are:
The total allowable equivalent vent length is:
Example: First Floor Installation
The equivalent vent length is:
Example: Connection to Masonry Chimney
The equivalent vent length is:
Harman® • XXV Installation Manual_R31 • 2004 -___ • 11/1517 3-90-00684i
C. Venting & Use of Elbows continued
Note:
Note:
Note:
Example:
No Change of Combustion
Blower Fan Blade Needed
0 Ft5 Ft 5 Ft
10,000
9,000
8,000
7,000
6,000
5,000
4,000
3,000
5 Ft
0 Ft
10 Ft
Combustion Blower Fan
Blade Changeover Line
Altitude
10 Ft
15 Ft
20 Ft
25 Ft
30 Ft
5 Ft
0 Ft
15 Ft
Equivalent Vent Length (EVL)
Maximum Horizontal Run
• NOTE:
• INSTALL VENT AT CLEARANCES SPECIFIED BY THE VENT MANUFACTURER
Harman® • XXV Installation Manual_R31 • 2004 -___ • 11/1518 3-90-00684i
D. Outside Air
Outside Air:
Hearth & Home Technologies recommend attaching
outside air in all installations, especially lower level and
Use silicone to create an effective vapor barrier at the
location where the chimney or outside air ducting passes
through to the exterior of the structure.
pipe goes here.
Figure 4.12
Direct Vent Wall Pass-through Kit
(Part #1-00-677177)
Figure 4.14
Inlet Cover part#
1-10-09542
Figure 4.13
Harman® • XXV Installation Manual_R31 • 2004 -___ • 11/1519 3-90-00684i
E. Locating Your Appliance & Chimney
G. Negative Pressure
F. Draft
Minimum Vacuum Requirements: .35 - .55
CAUTION
!
all
NOTICE: Hearth & Home Technologies assumes no
responsibility for the improper performance of the chimney
system caused by:
• Inadequate draft due to environmental conditions
• Downdrafts
• Tight sealing construction of the structure
• Mechanical exhausting devices
Risk of Asphyxiation! Negative pressure can cause
spillage of combustion fumes and soot.
WARNING
!
Harman® • XXV Installation Manual_R31 • 2004 -___ • 11/15 3-90-00684i
H. Avoiding Smoke and Odors
Negative Pressure, Shut-down, and Power Failure:
To reduce the probability of back-drafting or burn-back in
the pellet burning appliance during power failure or shut-
down conditions, the stove must be able to draft naturally
Outside Air
Vent Pipe
Hearth & Home Technologies assumes no responsibility
for, nor does the warranty extend to, smoke damage
caused by reverse drafting of pellet appliances under
shut-down or power failure conditions.
Other manuals for XXV
8
Table of contents
Other Harman Stove manuals
Harman
Harman XXV-TC User manual
Harman
Harman Super-Magnum Coal Stoker Stove Safety guide
Harman
Harman P43 User manual
Harman
Harman P43 User manual
Harman
Harman P43-C User manual
Harman
Harman Allure50 User manual
Harman
Harman TLC 2000 Installation instructions
Harman
Harman XXV User manual
Harman
Harman Absolute 43 User manual
Harman
Harman Oakwood Installation instructions
Harman
Harman Allure50 User manual
Harman
Harman P43 User manual
Harman
Harman XXV User manual
Harman
Harman Clarity 929 DV Installation instructions
Harman
Harman P43 User manual
Harman
Harman Magnum Stoker User manual
Harman
Harman Super-Magnum User manual
Harman
Harman P43 User manual
Harman
Harman XXV User manual
Harman
Harman SF 250 Installation instructions
Popular Stove manuals by other brands
Percy Doughty & Co
Percy Doughty & Co FIREFOX 5 CLEAN BURN II Installation and operating instructions
Lopi
Lopi Sturbridge owner's manual
Jøtul
Jøtul F 400 ECO Installation and operating instructions
St. Croix
St. Croix SCR Installation & operation manual
HWAM
HWAM 3120 operating instructions
Sergio Leoni
Sergio Leoni MARLENE P/I installation guide
Enviro
Enviro 50-1221 Technical manual
Wamsler
Wamsler K 118 Instructions for installation and use
Regency
Regency F38-NG2 Owners & installation manual
Contura
Contura C 32 installation instructions
Napoleon
Napoleon Bayfield GDS25N-1 Installation and operating instructions
Bullerjan
Bullerjan B3 Keramik MAX installation manual
MCZ
MCZ SUITE-CLUB-MUSA Hydromatic 18 M2 installation guide
United States Stove
United States Stove VOGELZANG VG5780 manual
Ribimex
Ribimex PRF315 User and maintenance manual
xeoos
xeoos Twinfire Basic Operating and installation instructions
Arada
Arada BK605 installation guide
Ravelli
Ravelli Infinity Plus 11 Use and maintenance manual