HARVEST H1392 User manual

1
H1392
ASSEMBLY MANUAL
(Do not operate with guards missing!)
(Do not operate tractor PTO over 540 RPM)
Read & understand all instructions pertaining to this option prior to operate.

2
Contents
H1392 ................................................................................................................................................................................ 1
Safety Alertness is the Business of everyone.......................................................................................................................... 4
Receiving and Unpacking .............................................................................................................................................. 7
Missing, Damaged or Replacement Parts ................................................................................................................... 7
Where to Start .................................................................................................................................................................... 7
AUGER TUBE IDENTIFICATION ............................................................................................................................................ 8
Flighting and Tube Assembly .............................................................................................................................................. 9
Step 1 .............................................................................................................................................................................. 9
Step 2 ............................................................................................................................................................................ 10
Step 3 ............................................................................................................................................................................ 10
Step 4 ............................................................................................................................................................................ 11
Discharge Assembly Installation ....................................................................................................................................... 11
Step 5 ............................................................................................................................................................................ 11
Step 7 ............................................................................................................................................................................ 12
Step 8 ............................................................................................................................................................................ 13
Step 9 ............................................................................................................................................................................ 13
You’re ready to install the In-Feed Housing...................................................................................................................... 14
Step 10 .......................................................................................................................................................................... 14
Step 11 .......................................................................................................................................................................... 14
Step 12 .......................................................................................................................................................................... 15
Step 13 .......................................................................................................................................................................... 16
Step 14 .......................................................................................................................................................................... 17
Step 15 .......................................................................................................................................................................... 18
Drive line (PTO) installation .............................................................................................................................................. 19
Step 16 .......................................................................................................................................................................... 19
Jack Stand installation....................................................................................................................................................... 22
Step 17 .......................................................................................................................................................................... 22
Installation of clean out and cover plates......................................................................................................................... 22
Step 18 .......................................................................................................................................................................... 22

3
Swing hopper lift arm........................................................................................................................................................ 24
Step 19 .......................................................................................................................................................................... 24
Installing the hydraulic lines and valves............................................................................................................................ 25
Step 20 .......................................................................................................................................................................... 25
Installation of cable brackets ............................................................................................................................................ 26
STEP 21.......................................................................................................................................................................... 26
Installation of backbone (option)...................................................................................................................................... 28
Step 22 .......................................................................................................................................................................... 28
Installation of the cables................................................................................................................................................... 28
Step 23 .......................................................................................................................................................................... 28
You are now ready to assemble the Under Carriage........................................................................................................ 32
Step 24 .......................................................................................................................................................................... 32
Installation of manual holder............................................................................................................................................ 41
Step 25 .......................................................................................................................................................................... 41
Installation of winch bracket............................................................................................................................................. 42
Step 26 .......................................................................................................................................................................... 42
Winch assembly ................................................................................................................................................................ 43
Step 27 .......................................................................................................................................................................... 43
Swing tube and hopper assembly ..................................................................................................................................... 43
Step 28 .......................................................................................................................................................................... 43

4
Safety Alertness is the Business
of everyone
Watch for this ALERT Symbol. It identifies potential hazards to Personal SAFETY and your HEALTH. It
points out SAFETY precautions
This SAFETY symbol means:
ATTENTION:
BE ALERT
Why is SAFETY Important to you?
THREE BIG REASONS:
*ACCIDENTS DISABLE AND KILL*
* ACCIDENTS COST*
*ACCIDENTS CAN BE AVOIDED*
Failure to read this Auger manual before assembling or operation of Auger is misuse of the equipment and a
needless risk to your HEALTH and SAFETY. Your life and limbs are worth keeping. Use this equipment with
care.
Symbol
Signal Words:
DANGER, WARNING, CAUTION:
The appropriate signal word for each message has been selected using the following
Guidelines below the Alert Symbol
BE ALERT!
DANGER- Indicates an imminently hazardous situation that, if not avoided, will result in death or serious injury. This
signal word is to be limited to the most extreme situations, typically for machine components that, for functional
purposes, cannot be guarded
Warning- Indicates an imminently hazardous situation that, if not avoided, will result in death or serious injury, and
includes hazards that are exposed when guards are removed. It may also be used to alert against unsafe practices
CAUTION- Indicates an imminently hazardous situation that, if not avoided, will result in minor or moderate injury. It
may also be used to alert against unsafe practices.

5
Read and understand this page prior to operation!
Do not operate with guards missing!
Shut tractor off prior to attaching or working with PTO shafts!
Augers and attchments
After the auger has been positioned, block the tires, front & rear so the auger cannot roll.
Make sure to keep all body parts away from hitch and pto area during operations.
Attach the auger pto shaft to the tractor pto shaft by sliding the knurled collar latch sleeve toward the center of
the knuckle cross, then push the auger pto shaft onto the tractor pto shaft until the knuled latch sleeve locks the
pto shaft into the groove on the tractor pto shaft.
After making sure the area around the auger pto shaft and swing hopper is clear of people and any loose articles,
slowly engage the tractor pto shaft.
With the auger running slow, gradually increase the pto rpm until it reaches operating speed and begin the
augering process.
Once the load is empty, let the auger run long enough to empty the auger and then shut off the tractor pto shaft.
After the first load has been unloaded and the pto shaft shut off, check the following:
1) Check all fasteners. Make sure they are tight and in the proper position.
2) Check position of sprockets. All sprockets should run inline with each other.
3) Check chain tension. Make sure idler sprocket hasn’t moved & chain has the proper tension.
4) Check all set screws. Set screws should be tightened to hold sprockets, couplers, & keys in place.
Lubrication Intervals:
PTO Shaft – grease every 50 hours of operation, both ends of pto shaft with high quality multi-lith grease
Bearings – grease every 50 hours of operation with high quality grease
Drive Chain – lube daily or more with high quality chain lube
Toolbars
Make sure to keep all body parts away from hitch and PTO area during operations.
If using a PTO Attach PTO shaft to the tractor PTO shaft by sliding the knurled collar latch sleeve toward the center of the
knuckle cross, then push the PTO shaft onto the tractor PTO shaft until the knurled latch sleeve locks the PTO shaft into
the groove on the tractor PTO shaft.
Lubrication Intervals:
PTO Shaft – grease every 50 hours of operation, both ends of pto shaft with high quality multi-lith grease
Bearings – grease every 50 hours of operation with high quality grease
Head trailers
Lubrication Intervals:
Bearings – grease every 50 hours of operation with high quality grease

6
Tools Needed To Assemble
(1) Electric Drill
(1) Hammer
(1) 3/8” Drill Bit
(1) 1/2” Drill Bit
(2) 9/16” Wrenches*
(2) 1/2” Wrenches*
(2) 3/4” Wrenches*
(2) 1-1/8” Wrenches*
(1) 5/16” Wrench
(1) 3/16” Allen Wrench METRIC AND STANDERD ALLEN WRENCHES
1) COMBINATION WRENCHES FROM 5/16” THRU 1 ½”
1) ½” DRIVE SOCKETS FROM5/16” THRU 1 ½”
4) LIFT STRAPS
2) PRY BARS, A LONG TAPERING PUNCH
2) PIPE WRENCHS
4) PLIARS AND CHANNEL LOCKS
2) COME ALONG OR CHAIN HOIST OR CABLE STRECHER
*Wrenches can be exchanged or used with sockets & a ratchet and/or an impact drive for ease of assembly

7
Receiving and Unpacking
1) Open all crates, boxes; pull out all parts, bags of parts, and hardware.
2) Now proceed to remove all shipping blocks and stops so that they are not left to cause damage to the auger or as
your laying them out
3) check to make sure you have the right amount of hardware, and that you have received all the parts and
hardware so that you will be able to find and assemble the auger, without missing or delay in final assembly,
Missing, Damaged or Replacement Parts
1) With the highest of standards we attempt to ship every order with all Parts necessary to
assemble our products, With that been said; We also understand that there are circumstances that or out of
our hands, to which parts may be misplaced, lost and/or damaged
2) If there is missing parts Tel: [phone] or 888.218.5373 to report the missing parts and\or hardware
so that they can be shipped directly out to you.
Where to Start
1) At this point you will need to decide what you want to work first the carriage assembly or with the tubes, if
you want to start with the carriage assemblies turn to page 35.
2) If you want to start with the tubes then go to the next page.
3) You will want to remove all the flighting from the tubes and inspect both them for any shipping damage. Reinsert
the flighting making sure that there is a stub shaft and open tube ends facing each other.
4) You will start from one end and working your way to the other end of the auger one tube junction at a time.

8
AUGER TUBE IDENTIFICATION
Tube 1
Tube 2
Tube 3
Tube 4
Tube 5
Tube 6
Infeed support brackets
Under carriage bracket
Swing
hopper
transport
bracket
Cable truss bracket base
Backbone brace
mounting bracket
Mast and
outrigger
mounting
bracket
and
support
Backbone brace
mounting bracket
Cable truss bracket base
Notice the distance
between flange and
cable truss bracket
base this one way to
tell tube 5 form 6
Cable truss bracket base
Cable
truss
mounting
point
Cable
truss
mounting
point
Factory used
only paint hook

9
Flighting and Tube Assembly
Step 1
1) Lay out the tubes on blocks or stands at a height that is comfortable to you to work with, make sure to keep
the blocks or stands near the tube flanges this way you will not damage the tubes by denting them in,
Align holes and make sure that the flighting aligns is like in Figure 1.1 not 180 degrees off,
2) ŝŶƐƚĂůůĂŶĚƚŝŐŚƚĞŶ;ϯͿзyϯĐŽƵƌƐĞƚŚƌĞĂĚ,ĞdžŽůƚƐĂŶĚзĐŽƵƌƐĞƚŚƌĞĂĚdŽƉ>ŽĐŬEƵƚƐĂƐƐŚŽǁŝŶŐŝŶ
Figure 1.2 the use of along tapered punch will help to align holes.
FIG 1- 1
FIG 1- 2
Stud end of Flighting
Receiver end of Flighting
Align Bolt Holes
Flighting properly aligned
(3) 5/8” Course threaded
Top Lock nuts
Align Flighting
ϱϴyϯ

10
Step 2
1) After this section of flighting is tightened slide the two tubes together and align the holes, as in figure 2.1, a
long tapered punch works best.
FIG 2- 1
FIG 2- 2
Step 3
1) Then you install a total of (10) ЪyϭЪĐŽƵƌƐĞƚŚƌĞĂĚ,ĞdžŽůƚƐĂŶĚ½”course thread flanged Nuts, as in figure
3.1, the use of a long tapered punch works to align bolt holes best.
Alignment of
tubes
;ϭϬͿЪyϭЪĐŽƵƌƐĞ
thread bolts and
½”flanged nuts

11
2) At tube #4 on the top side you will want to install the top and bottom ;ϮͿ;ϰƚŽƚĂůͿЪyϭЪĐŽƵƌƐĞƚŚƌĞĂĚ,Ğdž
Bolts and ½” course thread Top Lock Nuts to a snug fit so that you can install the quick link chain truss cable
bracket,
3) dŚĞŶŝŶƐƚĂůůƚŚĞĐĂďůĞďƌĂĐŬĞƚĂŶĚƌĞŵĂŝŶŝŶŐЪyϭЪĐŽƵƌƐĞƚŚƌĞĂĚ,ĞdžŽůƚƐĂŶĚЪŶƵƚƐ
Step 4
1) after all bolts are in make sure to tighten them all down, work your way back down the tubes, so that you can
recheck and make sure you have not missed installing or tighten the tube junction bolts.
Discharge Assembly Installation
Step 5
1) You are ready to install the Discharge Assembly, (fig5-1) if you are transporting the auger you will need to install
the red flag provided to you.
2) Slide the discharge assemble down over the flighting at the top of the auger.
FIG 5- 1
FIG 5- 2
Hub studs
Hub center
Flighting end hub
Discharge housing

12
Step 6
1) Watch the hub and line up the hub studs and the holes in the discharge assembly outer housing and finish
sliding the discharge assembly down so that it bottoms out onto the hub, (fig5-2) and install the (6) ½” fine
threaded lug nuts and ½” lock washers, have them flip over using the flat side of the nuts against the discharge
assemble with lock washers between the nuts and discharge assembly.
FIG 6- 1
Step 7
1) hƐŝŶŐ;ϭϬͿЪyϭЬďŽůƚƐĂŶĚĨůĂŶŐĞĚŶƵƚƐďŽůƚƚŚĞĚŝƐĐŚĂƌŐĞĂƐƐĞŵďůLJƚŽƚŚĞĂƵŐĞƌƚƵďĞĨůĂŶŐĞ
2) The bottom four bolts need to be inserted so that the bolt heads are on the inside, (fig 7.1) threads on the
outside of the discharge assembly so as to not be an area to slow down grain flow.
FIG 7- 1
This are the bolts to make
sure threads are outside
the discharge chute
This are the bolts to
make sure threads
are outside the
discharge chute

13
Step 8
1) Now with all bolts tighten down take the (2) 4” coiled springs with hooks on both sides open the overflow lid on
the discharge assembly (fig 8-1) and block it open with a block of wood, now hook the springs on the eye hook
on the inside of the discharge assemble on both the left and right sides.
FIG 8- 1
Step 9
1) Take a set of pliers and grab a hold of the spring with them and stretch it to the lid and hook it onto the eye
hooks on the inside of the lid.
2) Make sure that both springs are hooked up.
FIG 9- 1
Factory used, paint
hook only.
Discharge overflow hood spring hooks
1/2" Flange Nut
Discharge overflow hood
Discharge
overflow hood
Discharges overflow
ƐƉƌŝŶŐyϮ
Factory used, paint
hook only.
Inside spring hooks

14
You’re ready to install the In-Feed Housing
Step 10
1) Start by sliding the in feed housing over the flighting that is protruding for auger tube one,
2) The in feed will have the tongue on one side and an opening the same size as the auger on the other,
3) ^ůŝĚĞŝƚďĂĐŬƚŝůůŝƚŝƐĂŐĂŝŶƐƚƚŚĞĂƵŐĞƌƚƵďĞĨůĂŶŐĞƚĂŬĞ;ϲͿЪyϭЪĨůĂŶŐĞďŽůƚƐŝŶƐĞƌƚƚŚĞŵƐŽƚŚĂƚƚŚĞďŽlt
ŚĞĂĚƐĂƌĞŽŶƚŚĞƚƵďĞƐŝĚĞĂŶĚƚŚĞƚŚƌĞĂĚĂƌĞŽŶƚŚĞŝŶĨĞĞĚƐŝĚĞƚŚĞ;ϰͿďŽƚƚŽŵЪyϭЪďŽůƚƐĂƌĞŝŶƐĞƌƚĞĚƐŽ
that the threads are on the tube side and the heads or on in feed side, use (10) ½” flange nuts tighten all bolts.
FIG 10- 1
Step 11
1) dĂŬĞƚŚĞďĞĂƌŝŶŐǁŝƚŚƚŚĞϰďŽůƚƐƋƵĂƌĞŚŽƵƐŝŶŐϭЬŝŶƐŝĚĞďŽƌĞĂŶĚĞĐĐĞŶƚƌŝĐůŽĐŬŝŶŐĐŽůůĂƌ
FIG 11- 1
2) Slide it over the top shaft which is located and protruding outwards towards the top of the in feed assemble, use
;ϰͿЪyϭЪĨůĂŶŐĞďŽůƚƐĂŶĚƉůĂĐĞƚŚĞЪĨůĂŶŐĞŶƵƚƐŽŶƚŚŽƵŐŚƚƚŚĞďŽƚƚŽŵŝŶƐƉĞĐƚŝŽŶŚŽůĞĨƌŽŵŝŶƐŝĚe of the
in feed housing, making sure that the grease fitting is pointing up,
3) Push on the locking collar against the bearing, turn the collar clockwise to lock, using a punch tap the lock collar
till tight. Tighten set screw on lock collar using Allen wrench.
Auger Tongue 
Infeeder housing
First tube assemble
ϭЬďŽƌĞďĞĂƌŝŶŐ
block
Auger flighting
shaft
Grease fitting


15
FIG 11- 2
Step 12
1) Locate the bearing cover and the bearing 4 bolt square housing, 1 ¾” inside bore and eccentric locking collar
FIG 12- 1
2) ^ůŝĚĞŝƚŽǀĞƌƚŚĞďŽƚƚŽŵƐŚĂĨƚǁŝƚŚƚŚĞŐƌĞĂƐĞĨŝƚƚŝŶŐŽŶƚŚĞůĞĨƚƐŝĚĞƵƐĞ;ϰͿЪyϭЪĨůĂŶŐĞďŽůƚƐĂŶĚƉůĂĐĞƚŚĞ
½” flange nuts on thought the bottom inspection hole from inside of the in feed housing, tighten bolts.
3) Take the lock collar and slip it over the shaft and push it against the bearing turn the lock collar counter
clockwise, using a punch and hammer to tap it to lock it, tighten the set screw on the lock collar with a Allen
wrench
Grease fitting

1 ¾” bore bearing
block
Lock collar 
Lock collar


16
Step 13
1) Turn both shafts so that the keyways are facing up, tap the key stock into the top shaft now place the first of two
key stock for lower shaft keeping it 1” from the lock collar tap it in,
FIG 13- 1
2) Take sprocket part #11052 and slide it on the top shaft, take sprocket part #10555 and slide it onto the lower shaft
.
FIG 13- 2
FIG 13- 3
#11052
sprocket
#10555
sprocket 
Key stock

17
FIG 13- 4
FIG 13- 5
Step 14
1) Take the ½” x 2” carriage bolt and place it thought the hole on the bracket for the idler sprocket and slide it
toward the other sprockets now place the (7) ½” flat washers on the bolt you may want to put a piece of tape on
them to hold the in place.
FIG 14- 1
Idler sprocket

10555
Sprocket
11052 sprocket




Idler
sprocket

18
Step 15
1) Take ŝĚůĞƌƐƉƌŽĐŬĞƚƉĂƌƚηϭϬϯϬϬĂŶĚƐůŝĚĞŝƚŽŶƚŽƚŚĞЪyϮĐĂƌƌŝĂŐĞďŽůƚǁŝƚŚƚŚĞ;ϳͿĨůĂƚЪǁĂƐŚĞƌƐ
2) Take the #60 chain part
#10552A
FIG 15- 2
3) lay it around the two sprockets so the gap meets on one side or the other or the top of the top sprocket whichever
is easier for you,
4) Take part # 10822 ½ link
FIG 15- 3
5) and part # 10553
FIG 15- 4
#10300
sprocket
FIG 15- 1FIG15- 1FIG 15- 1
FIG 15- 2

19
1) chain connector and connected the chain then slide the idler in to take up the slack in the chain
FIG 15- 5
Drive line (PTO) installation
FIG 16- 1
Step 16
1) Tap in the 2nd key stock into lower shaft about ½” from sprocket, take the drive line (PTO) and slip it on the lower
shaft.
PTO shaft

PTO shield
tractor side 
PTO
shield
infeed
side

20
FIG 16- 2
1) >ŝŶĞƵƉƚŚĞWdKŚŽůĞƐǁŝƚŚƚŚĞŚŽůĞƐŝŶƚŚĞůŽǁĞƌƐŚĂĨƚĂŶĚƚĂŬĞϯϴyвƚŚƌĞĂĚĐƵƚƚŝŶŐďŽůƚŝŶƐƚĂůůŝŶƚŽƚŚĞŚŽůĞƐ
and tighten bolt.
2) Place the chain guard (FIG 16-3) over the drive line(PTO) and push it against the in feed assemble line up bolt holes
and place (4) ďŽůƚƐϯϴyвƐĞůĨ-cutting thread bolts
FIG 16- 3
3) Locate the chain guard cover (FIG 16-4) this guard is slotted to allow you to slide it up from the bottom side of the
ĚƌŝǀĞůŝŶĞ;WdKͿĂůŝŐŶŚŽůĞƐĂŶĚƚŝŐŚƚĞŶƵƐŝŶŐвyϭhE&ůĂŶŐĞĚŚĞĂĚĞĚďŽůƚƐ
FIG 16- 5
FIG 16- 4
CHAIN IDLER SPROCKET


SECOND KEY
STOCK