aivituvin GUT02 User manual

INSTRUCTION
MANUAL
GUT02
www.aivituvin.com

Please retain these instructions for future reference.
NOTICE
Firmly secure all bolts,screws and knobs before use.
Reconfirm that all bolts,screws,and knobs are secure every 90
days.
Fasten screws loosely during initial assembly. Do not fully
tighten screws until the item is completely assembled.
Do not use or store this item in the proximity of open flame or
flammable/combustible chemicals.
Be aware that some parts are heavy and have sharp edges.
Be aware that moving parts can injure,crush and cut.
If any parts are missing,broken,damaged,or worn,stop using
this product until repairs are made and/or factory replacement
parts are installed.
Do not use this item in a way inconsistent with the
manufacturer’ s instructions as this could void the product
warranty.
01

TOOLS REQUIRED
PHILLIPS
SCREWDRIVER
DRILL
(RECOMMENDED)
2PERSON
ASSEMBLY
APPROXIMATELY
30MIN. ASSEMBLY
HARDWARE
20PCS++1 spare
P1 P2
P3
02
M3.5x60mm SCREW
36PCS++1spare
M3.5x35mm SCREW
4PCS spare
M6.0x90mm SCREW

PARTS
A B C
C1 D E
F
Side panel
1PC
Bottom panel
1PC
Bottom panel
1PC
Asphalt roof
1PC
1PC 1PC 1PC
A B C
DEF
G
2 PCS
2 PCS
03
HI
1 PC 2 PCS
2 PCS
2 PCS
4 PCS
Short panel with slot
2 PCS Long panel with slot
Leg A Leg B Short panel
Long panel-Second level
Long panel-Bottom level Bottom panel H Bottom panel I
2 PCS

PARTS
A B C
C1 D E
F
Side panel
1PC
Bottom panel
1PC
Bottom panel
1PC
Asphalt roof
1PC
1PC 1PC 1PC
J K L
MN
2 PCS Base panel
04
12 PCS
2 PCS
Bottom panel J
2 PCS Supporting panel K
Supporting for side table Side table panel
1 PC
O
Divider O
3 PCS
PQ R
4 PCS Inner lining
1 PC
Divider P
1 PC Leg end

A B C
C1 D E
F
Side panel
1PC
Bottom panel
1PC
Bottom panel
1PC
Asphalt roof
1PC
1PC 1PC 1PC
05

PRODUCT ASSEMBLY
01
02
06
Repeat to build another set of legs.
①
Slide two Part C and one Part D short panels into Part A & Part
B legs
Secure panels with P2X4.
②
D
P2 X4
C
A
B
A
BC
D
P2 X4

PRODUCT ASSEMBLY
03
04
07
Slide a Part G, Part F,Part E orderly into the legs.Secure panels
with P2X4.
Repeat on the other side.
P2 X4
E
GF
P2 X4
E
GF

PRODUCT ASSEMBLY
05
06
08
Insert two Part J and one Part H,two Part I bottom panels.
Attach Part K to legs with bolt P1X2
JH
I
J
K
P1 X2
I

PRODUCT ASSEMBLY
07
08
09
Attach Part L to Part K with P3X12.
Repeat on the other side.
P1 X2
K
LX12
P3 X12

PRODUCT ASSEMBLY
09
10
10
Insert the Part R inner lining.
Screw P3X12 on the other side.
P3 X12
R

PRODUCT ASSEMBLY
11
11
Stuck in divider one Part P and three Part O into the slots.
①Attach two Part M to with P2X4.
12
②
【
The side table can be assemble on left/right side either. Both
pre-drilled are included！

OOOP
MX2
P2 X4
】

PRODUCT ASSEMBLY
13
12
① Attach Part N to the Part M with P3X4.
②
【The side table can be assemble on left/right side either. Both
pre-dilled holes are included!
P3 X4
Attach four Part Q leg ends with P3X8.
14
N
P3 X8
QX4
】

WARNING
Manufacturer and seller expressly disclaim any and all liability for personal injury,property
damage or loss,whether direct,indirect,or incidental,resulting from the incorrect
attachment,improper use,inadequate miantenance,or neglect of this product.