HARVEY GYRO AIR G700 User manual

Revision A (2021-01-30)
298002912

2
Index of Contents
Contents ................................................................................................................................................ 2
1. Foreword...................................................................................................................................................3
2. Machine Description................................................................................................................................3
2.1 Feature Identification.................................................................................................................... 3
2.2 Specification...................................................................................................................................4
2.3 Requirement of electrical power................................................................................................. 5
3. Safety Regulations.................................................................................................................................. 7
3.1 General Safety Instructions......................................................................................................... 7
3.2 Specific Safety Instructions for Dust processor........................................................................8
4. Installation of the machine..................................................................................................................... 9
4.1 Transportation of machines......................................................................................................... 9
4.2 Unpacking.................................................................................................................................... 10
4.3 Positioning the machine............................................................................................................. 11
4.4 Assembly.......................................................................................................................................11
4.4.1 Moving & Placing Base Unit...................................................................................................11
4.4.2 Installation of dust extractor adaptor.................................................................................... 15
5. Operations.............................................................................................................................................. 16
5.1 The operating and instructions of electrical components..................................................... 16
5.2 The operating of manometer.....................................................................................................17
5.3 Clean the dust bin....................................................................................................................... 17
5.4 General operation....................................................................................................................... 17
6. Maintenance...........................................................................................................................................18
7. Trouble shooting guide......................................................................................................................... 19
8. Breakdown & Parts List........................................................................................................................ 21

3
1. Foreword
This manual was developed as an integral part of this machine. It contains basic information for
qualified operating staff. It also contains all necessary information for the correct and safe
operation.These regulations, however, cannot cover all other safety aspects. Operator must
peruse and make sense of this manual before starting to use the machine.
2. Machine Description
The G-700 dust processor is a revolutionary dust extractor with the unique GYRO AIR technology.
Unlike any existing dust extractors in the world, G-700 directs dust flow into the Gyro Air system
that generates powerful centrifugal force and efficiently separates dust from air. With this special
technology, G-700 delivers unprecedented performance, including a 99.9% separation efficiency
before Filter and significantly reduces noise levels.
The dust processor G-700 is used only for wood chips or other dust collection, do not collect
liquid, poisonous gas, explosive goods and viscous substances or other potentially dangerous
substances
The G-700 dust processor is designed to collect dust from one or two machines at the same time.
This can be accomplished by either connecting it to multiple machines using blast gates to control
which branch is active.
The dust processor is intended to be operated not far from the machine needing dust collection
Only a skilled operator or worker instructed and trained may operate the machine. While working
on the machine the operator must be familiar with these instructions and comply with safety rules,
regulations and provisions in force in the respective country.
2.1 Feature Identification (Fig.1)
A
Dust extractor adaptor
B
Control panel
C
Buzzer
D
Pressure Gage
E
Handle
F
Window
G
GYRO Air separate
H
Filter Cleaning Knob
I
Filter(inside)
J
Fine dust cleaning port
K
Dust bin(inside)
L
Door
Fig.1

4
2.2 Specification
Model：G-700
Imperial
Metric
Electrical
Power Requirement:
220V,Single Phase,50/60Hz
Breaker Size:
20A
Inverter Type:
INOVANCE MD200
Motor
Type:
TEFC Induction
Power:
1.5Kw(2HP)
Phase:
3Phase
Rated Amps:
5.8A
Speed:
2280-4275rpm Variable
Product Dimensions
Overall Dimension:
56-1/4x23-1/2x33-7/8"
1430x579x858mm
Packing Size:
59x28-1/2x42-1/4"
1500x725x1072mm
Product Weight
Net Weight:
445lbs
195KG
Gross Weight :
510lbs
222KG
Performance
Max. Air Flow:
1110CFM
1885 m3/h
Max.Static Pressure:
18-1/2 inches of water
4600Pa
Max.Air Flow @4 inch hose:
700CFM
1190 m3/h
Static Pressure @ 4 inch hose:
5-5/8 inches of water
1400Pa
Impeller Size:
12inch
Φ300mm
Main Inlet Size:
6inch
Φ150 mm
Adapter Inlet Size:
4 inch x 2
Φ100 mm x 2
Filter Emission Rating:
0.05mg/m³
0.05mg/m³
Filter Surface Area:
75 SF
7 m2
Noise Rating @3m
61-72 dBA
61-72 dBA
Max.Dust Bin Capacity:
32GAL
120L
Manual Filter Cleaning:
Yes
Intelligent Dust-Full Monitoring system:
Yes
Pressure Gauge:
Yes
Remote Control
Yes
Every machine we produce is fitted with a name plate with its serial number. The number
is also punched on the machine.
An exact description of the machine model and serial number will facilitate rapid and
effective replies from our after-sales service.
Position of nameplate is on the side of the main base unit.

5
2.3 Requirement of electrical power
Power requirement: 220VAC / 1PH
The machine needs no further electrical installation. Equipment comes with 1.8 meters of cable
with a plug. For longer runs, please use an appropriate extension cord meeting your local area
codes.
The input power supply of the machine is 1PH, AC220V. The steady-state AC power supply is
0.9～1.1 times of the rated value.
2.3.1 Equipment grounding
This machine must be grounded, if it should malfunction or breakdown, grounding provide a path
of least resistance for electric current to reduce the risk of electric shock. This appliance is
equipped with a cord having an equipment-grounding conductor and grounding plug. The plug
must be inserted into an appropriate outlet that is properly installed and grounded in accordance
with all local codes and ordinances.
WARNING – Improper connection of the equipment-grounding conductor can result in a risk of
electric shock. Check with a qualified electrician or service person if you are in doubt as to
whether the outlet is properly grounded. Do not modify the plug provided with the appliance – if it
will not fit the outlet, have a proper outlet installed by a qualified electrician.
This appliance is for use on a circuit having a nominal rating 220 V and is factory-equipped with a
specific electric cord and plug to permit connection to a proper electric circuit recommend
minimum 20A circuit breaker. Make sure that the appliance is connected to an outlet having the
same configuration as the plug. No adaptor should be used with this appliance. If the appliance
must be reconnected for use on a different type of electric circuit, the reconnection should be
made by qualified service personnel.
2.3.2 Cable inspection and Extension
Before using, you need to check the power plug and cable to see if there is any damage. If any,
should be immediately repaired or replaced.
We do not recommend using an extension cable with this machine. If you must use an extension
cable, only use it if absolutely necessary and only on a temporary basis. Extension cable cause
voltage drop, which may damage electrical components and shorten motor life. Voltage drop
increases as the extension cable size gets longer and the cable size gets smaller. Any extension
cord used with this machine must contain a ground wire, match the required plug and receptacle,
Any extension cable used with this machine must contain a ground wire, match the required plug
and receptacle
Minimum Gauge Size ........................... 2.5mm2(14 AWG)
Maximum Length (Shorter is Better).......15m (50 ft).

6
2.3.3 Electrical diagram(Fig.2)
Fig.2

7
3. Safety Regulations
3.1 General Safety Instructions
1. Read and understand the owner’s manual and labels affixed to the machine. Learn its
application and limitations as well as its specific potential hazards.
2. The power supply socket or terminals need reliable grounding.
3. Keep in good working order, properly adjusted and aligned. Cluttered areas and benches invite
accidents. Make sure the floor is clean and not slippery due to wax and sawdust build-up.
4. WARNING ! – To reduce the risk of electric shock:
Do not expose the machine to water or moisture.
Do not use outdoors.
5. Do not use this machine within the designated safety areas of flammable liquid stores or in
areas where there may be volatile gases. Keep work area clean, dry, and well-lighted.
6. Keep children from reaching this machine.
7. Don’t force the machine or the attachment to do a job for which it was not designed.
8. Do not wear loose clothing, gloves, neckties or jewelry (rings, watch) because they could get
caught in moving parts. Non-slip footwear is recommended. Wear protective hair covering to
contain long hair. Roll up long sleeves above the elbows.
9. Do not use this machine if you are tired, your attention is wandering or you are being subjected
to distraction.
10. If the work operation appears to be excessively noisy, wear ear protection.
11. Always wear safety glasses or a face shield when operating or observing machinery to reduce
the risk of eye injury or blindness from flying particles. Everyday eyeglasses are not approved
safety glasses.
12. WARNING ! – To reduce the risk of electric shock:
Always unplug the machine during servicing.
13. WARNING ! – To reduce the risk of injury from moving parts :
Always unplug before servicing.
14. Make sure the power switch is on the “OFF” position before plugging in.
15. Turn power ‘’OFF’’. Don’t leave until it comes to a complete stop.
16. Regularly inspect machine for damaged parts, loose bolts or any other conditions that may
affect safe operation. Always repair or replace damaged parts before operating machine.
17. Keep the machine clean; it will enable you to more easily see any damage that may have
occurred. Clean the machine with a damp soapy cloth if needs be, do not use any solvents or
cleaners, as these may cause damage to any plastic parts or to the electrical components.

8
3.2 Specific Safety Instructions for Dust Processor
1. CLEAN ENVIRONMENT
Once you are ready to commence work, remove any tools, objects or items that could
inadvertently get ‘sucked up’ by the machine and place safely out of the way.
2. INTENDED USE
Don't use this machine as a vacuum cleaner, avoid stones, nails, etc., as it may produce a spark
and cause fire or explosion.
3. FIRE SUPPERSSION
Only operate the dust collector in locations that contain a fire suppression system or have a fire
extinguisher nearby.
4. REGULAR CLEANING
Regular check/empty the collection bags to avoid the buildup of fine dust that can increase the
risk of fire. Make sure to regularly clean the surrounding area where the machine is operated
--excessive dust buildup on overhead lights, heaters, electrical panes, or other heat sources will
increase the risk of fire.
5. STATIC ELECTRICITY
Plastic dust lines generate high amounts of static electricity as dust chips pass through them.
Although rare, sparks caused by static electricity can cause explosions or fire. To reduce this risk,
make sure all dust lines are thoroughly grounded by using a grounding wire.
6. HAZARDOUS DUST
Dust created while using machinery may cause cancer, birth defects, or long-term respiratory
damage. Be aware of dust hazards associated with each workpiece material, and always wear a
NIOSH-approved respirator to reduce your risk.
7. DUST ALLERGIES
Dust from certain woods may cause an allergic reaction in people and animals. Make sure you
know what type of wood dust you will be exposed to in case there is a possibility of an allergic
reaction.
8. IMPELLER HAZARDS
Do not place your hands or tools near the open inlet during operation for any reason. The
powerful suction could easily cause accidental contact with the impeller which will cause serious
personal injury or damage to the machine. Always keep small animals and children away from
open dust collection inlets.

9
4. Installation of the machine
This machine need a little assembly, almost can be used directly.
4.1 Transportation of machine
4.1.1 Transportation and store
Anti-rust and shock proofing measures have been taken during packing. The machine should be
transported and stored in -25~55°C ambient temperature.
Take care not to allow the machine to be exposed to rain or damage to the packing during
transportation and storage.
●While transporting or handling the machine, be careful and let the activity be done by
qualified personnel especially trained for this kind of activity!
●While the machine is being loaded or unloaded, make sure that no person is too close to
be subject to injury
●Select proper transportation device according to the weight of the machine.
●Make sure the lifting capacity of transportation device is capable for the weight of the
machine.
4.1.2 Transportation before unpacking
As standard, the machine is packed in a robust wooden
box. Fig.3 shows the method can be used to transport the
packing box.
Fig.3
4.1.3 Confirmation after unpacking
When open the packing box, please pay attention to the following items. If you have any
questions, please contact directly with us.
1) Has the machine been damaged in transportation.
2) All accessories and documents are there.
3) The product is consistent with the contract.
4) The specifications on machine label are consistent with the contract.
4.1.4 Transportation after unpacking
When transporting the machine with a stacker truck, first find the center of gravity of the
machine, insert the fork below the machine and then lift carefully.

10
4.2 Unpacking
This machine was carefully packaged for safe transportation, remove the package materials from
your machine and inspect it. If you find the machine damaged, please immediately call
Customer Service for advice.
Save the containers and all packing materials for possible inspection by the carrier or its agent.
Otherwise, filing a freight claim can be difficult.
When you are completely satisfied with the condition of your shipment, inventory the contents.
Inventory:
The following is a description of the model components shipped, lay the components out to
inventory them.
If you can't find an item on this list, check the mounting location on the machine or
examine the packaging materials carefully. Occasionally we pre-install certain
components for shipping purposes.
Fig.4
Box Contents(Fig.4):
A. Machine(1)
B. φ100mm x 2m long flexible hose (1)
C. Dust extractor adaptor (1)
D. Handel(1 )
E. Tools(1 set)
All other parts except main unit are positioned in the dust collection box. Open the front door and
get them.