HARVEY GYROAIR G700 User manual

G700
Filter Assembly Replacing Instruction
Filter assembly need to replace regularly (normally twice a year), it must use the
matched filter assembly, as
图片位置不好
不清晰,
Fig.1
1. Remove the Cover
As shown in Fig.2
, loosen 4 hex screws(A), remove screws(B), then remove the
cover(C)
字母大小
Fig.2
2.
Remove the Filter Cover
Open the front cover, remove the back cover and dust bin, as shown in
remove
4 screws on the right side of the frame
图比例不对
Fig.3
不清晰
Filter Assembly Replacing Instruction
Filter assembly need to replace regularly (normally twice a year), it must use the
matched filter assembly, as
Fig.1shown
, loosen 4 hex screws(A), remove screws(B), then remove the
Remove the Filter Cover
Open the front cover, remove the back cover and dust bin, as shown in
4 screws on the right side of the frame
Filter Assembly Replacing Instruction
Filter assembly need to replace regularly (normally twice a year), it must use the
, loosen 4 hex screws(A), remove screws(B), then remove the
Open the front cover, remove the back cover and dust bin, as shown in
Fig.3,

As shown in Fig.4，
remove 4
不清晰
字母大小
Fig.4
3.
Remove and Reinstall the Filter Assembly.
As shown in Fig.5，
remove 4
inside the separator system, remove 8 screws(G), then remove the filter
assembly
Notice: Mark the position where the assembly is installed, it sho ld be
reinstalled to the same position.
字母大小
Fig.5
As shown in Fig.6
, loosen the strap(I), remove the dust collector(J), clean it up
especially the lip for future use
Fig.6
remove 4
locking screws (E)，
then remove the filter cover
Remove and Reinstall the Filter Assembly.
remove 4
screws(F)，
these screws was fastened by nut(F)
inside the separator system, remove 8 screws(G), then remove the filter
Notice: Mark the position where the assembly is installed, it sho ld be
reinstalled to the same position.
, loosen the strap(I), remove the dust collector(J), clean it up
especially the lip for future use
then remove the filter cover
。
these screws was fastened by nut(F)
inside the separator system, remove 8 screws(G), then remove the filter
Notice: Mark the position where the assembly is installed, it sho ld be
, loosen the strap(I), remove the dust collector(J), clean it up

As shown in Fig 7，
remove hex nuts(K)
then remove the filter assembly and install a new one
字母大小
Fig.7
Apply sealer on the lip of the clean dust collector, then install it back to the end
of the filter, then fasten the strap
Notice: the direction of the d st collector sho ld be the same as shown in
Fig.6.
4.
Reinstall the new filter back to its original position as shown in
.
Reinstall the filter cover by step 2.
6.
Reinstall the cover by step 1.
remove hex nuts(K)
，
As shown in Fig 8, remove 6
then remove the filter assembly and install a new one
Fig.8
Apply sealer on the lip of the clean dust collector, then install it back to the end
of the filter, then fasten the strap
Notice: the direction of the d st collector sho ld be the same as shown in
Reinstall the new filter back to its original position as shown in
Reinstall the filter cover by step 2.
Reinstall the cover by step 1.
As shown in Fig 8, remove 6
screws(L)，
Apply sealer on the lip of the clean dust collector, then install it back to the end
Notice: the direction of the d st collector sho ld be the same as shown in
Reinstall the new filter back to its original position as shown in
Fig.5.