Hasbro Play-Doh Creativity Table 23070 User manual

Phillips/cross head screwdriver (not included) required for assembly.
AGES 3+
23070
CONT NTS: 4 five-ounce cans and 4 two-ounce cans of PLAY-DOH Brand
Modeling Compound (Net Weight 28 oz., 793 grams), tabletop center,
2 tabletop ends, 4 table legs, carousel, roller, ruler, FUZZY PUMP R®extruder,
extruder ring, extruder post, extruder rail, FUN FACTORY®extruder, 4 shelves,
4 crayons, 4 markers, 10 sheets of paper, bag of screws.
CCrreeaattiivviittyy TTaabbllee™ CCrreeaattiivviittyy TTaabbllee™
WARNING: This product contains small parts which
are necessary for assembly. Prior to and during assembly
of this product, keep small parts out of children’s reach.
Small parts pose a choking hazard to children under 3.
Adult assembly
required.

AASSSSEEMMBBLLYY
RULER
ROLLER
4. Stand table on legs. Snap
carousel onto tabletop.
Snap FUZZY PUMPER post
onto tabletop. Snap FUN
FACTORY extruder onto
tabletop.
5. Fit 4 shelves into either of
the legs with shelf slots.
6. Slide roller onto ruler.
3. Push and snap legs onto table as shown. Be sure to match
the letter on the leg with the letter on the table.
2. Turn tabletop
assembly over. Use a
Phillips/cross head
screwdriver to tighten 3
screws into tabletop
center/end on one side.
Repeat for other side.
1. Fit 2 tabletop ends onto tabletop
center.
TABLETOP
CENTER
TABLETOP ENDS
FUZZY PUMPER POST
CAROUSEL
FUN FACTORY
EXTRUDER
SHELVES

FFUUZZZZYY PPUUMMPPEERR
1. Fill FUZZY PUMPER extruder with
PLAY-DOH compound.
2. Slide extruder ring over extruder.
3. Slide FUZZY PUMPER extruder onto
post to extrude compound!
DDRRAAWWIINNGG
1. Use the markers and crayons to
write, draw pictures on the paper!
RRUULLEERR DDEESSIIGGNNSS
1. Press PLAY-DOH compound
into recess in ruler.
2. Place extruder rail over
compound.
3. Slide the roller over the rail for
cool creations!!
FFUUNN FFAACCTTOORRYY
1. Fill FUN FACTORY extruder with
PLAY-DOH compound.
2. Slide the extruder rail on and choose
the shape you want.
3. Press the FUN FACTORY handle to
extrude compound!
PPLLAAYY FFEEAATTUURREESS

PLAY-DOH and the PLAY-DOH logo are trademarks identify-
ing quality modeling compound products produced exclu-
sively by Hasbro, Inc.
© 2003 Hasbro. All Rights Reserved.
® denotes Reg. U.S. Pat. & TM Office.
23070 P/N 6241080000
EEAASSYY 33--SSTTEEPP CCLLEEAANNUUPP!!
1. Place PLAY-DOH Brand Modeling Compound back in cans
and seal lid.
2. Remove excess from carpets/fabrics, then allow remaining
compound to dry.
3. Loosen dried compound with stiff brush and vacuum clean. If
necessary, brush with gentle soap and cold water. (Do not use hot
water or cleaning solutions to clean PLAY-DOH compound from
carpets/fabrics.)
Note to parents: markers and crayons may stain certain surfaces.
Use soap and warm water to clean.
PLAYDOH.COM
PLAYDOH.COM
FOR NEW PRODUCTS AND OFFERS
FOR NEW PRODUCTS AND OFFERS
Questions? Call: 1-800-327-8264
SSTTOORRAAGGEE
- Store PLAY-DOH cans in the can holders on the shelves.
- Place crayons and markers in the carousel.
- Store roller on a shelf; store ruler and extruder rail in paper tray.
Results vary depending on child’s age and level of skill.
NONTOXIC CONFORMS TO ASTM D-4236