Hathaway OUTLAW NG1040 User manual

OUTLAW FREE STANDING
DART CABINET
ASSEMBLY INSTRUCTIONS
NG1040
Please Do Not Hesitate to
Contact Our Consumer Hotline
at 800-759-0977
with Any Questions That May
Arise During Assembly or
Use of This Product!

THANK YOU!
Thank you for purchasing this product.
We work around the clock and around the globe to ensure that our products
maintain the highest possible quality. However, in the rare case of issues
during assembly or use of this product, please contact our Consumer Hotline
at 800-759-0977 for immediate assistance before contacting your retailer.
Please read the warranty information at the back of these assembly
instructions for further details.
IMPORTANT! PLEASE READ THESE ASSEMBLY INSTRUCTIONS
IN ENTIRETY BEFORE ASSEMBLING YOUR PRODUCT.
2

PARTS IDENTIFIER (NOT TO SCALE)
#9
3 pcs
DRAOBEGAROTS
#10
1 pc
#11
2 pcs
LEGSHINGE
#13 #14 #15
4 pcs
1/4"x1" BOLT
6 pcs
1/4" WASHER
6 pcs
#12
#17
#21 #22
#18 #19
#16
#1 #2 #3 #4 #5
#6 #7 #8
#20
2 pcs
SIDE PANEL
2 pcs
CROSS BOARD 1 pc
COVERPLATE 1 pc
BASE PLATE 1 pc
TOP BACK BOARD
2 pcs
DART HOLDER
2 pcs
SIDE PANEL 1 pc
COVER PLATE
2 pcs
DOOR
GEAR
35 pcs
TLOBDAERHT
35 pcs
DOOR HANDLE
2 pcs
1/2" SCREW
16 pcs
1/2" FLAT SCREW
4 pcs
1" SCREW
4 pcs
3/4" FLAT SCREW
28 pcs
ADDITIONAL EQUIPMENT REQUIRED:
3
Please see Parts List at end of manual for part number when ordering parts. For replacement parts please call 800-759-0977.
#23
ALLEN KEY
1pc
3/8" BOLT
4 pieces
#24 #25
1 set
ELECTRONIC TARGET
B
A
B
A
BOTTOM BACK BOARD
#26 #27
#28 #29
5/8" SCREW
4 pcs
3/8" FLAT SCREW
4 pcs
MAGNETIC PART
2 pcs
STEEL PLATE
2 pcs

ASSEMBLY TIPS
1. Find a clean, level surface to begin the assembly of your game table. The table will be
partially assembled upside down and then turned over onto its legs. This is a heavy game
and turning it over will require at least two strong adults.
2. Remove all of the contents from box and verify that you have all of the parts shown on the
Note: Some parts may be pre-installed or
pre-assembled.
understand the text before beginning each assembly step.
4. When installing parts that have more than one screw or bolt, hand tighten all screws or
bolts in place before finishing tightening with screwdriver or hex wrench.
5. Electric screwdrivers may be helpful during assembly; however, please set a low torque
and use extreme caution because screws may be stripped or overtightened if the electric
screwdriver's torque is set too high.
WARNINGS!
READ AND FOLLOW ALL ASSEMBLY, OPERATION AND SAFETY INSTRUCTIONS CAREFULLY.
CHOKE HAZARD - THIS TABLE CONTAINS SMALL BALLS AND PARTS - NOT
SUITABLE FOR CHILDREN UNDER 3 YEARS OF AGE.
4

ASSEMBLY INSTRUCTIONS
#20
#20
#21
#2A
#1B
#3
#1A
#2B
#4
#21
#21
#21
#21
#19
#5
5
Step 1: Screw thread bolts #21 into the side panel #1A and #1B, and cross board #2A and #2B
as shown below. Insert gears #20 into cover plate #3, base plate #4 and cross board #2A
and #2B. Note: see illustration below for alignment of gear to hole. Attach cross board #2A to
base plate #4 with gears #20. Attach cross board #2B to cover plate #3 with gears #20.
Attach side panel #1A and #1B to plates #3 and #4 in the same manner.
Step 2: Attach the top back board #5 to the assembled cabinet with screw #19.
Note: Position top back
board so four dartboard
mounting holes are closer
to the top than bottom of
cabinet.
Note: When gear is inserted into
hole, the arrow should point
directly out toward hole that
bolt will be inserted into.
Once bolt is inserted, turn gear
clockwise to lock.

ASSEMBLY INSTRUCTIONS (CONT.)
#10
#19
6
.6#lenapedisdna7#etalprevocotni12#stlobdaerhtwercS:3petS Insert gears #20 into storage
shelves #9. Attach cover plate #7 and storage shelves #9 to side panel #6 with gear #20
as shown. Repeat for other side panel #6. Attach magnetic part #26 to pre-drilled holes on
center of long side of board #7 with screw #28.
Step 4: Attach the bottom back board #10 to the assembled cabinet with screw #19.
#7
#6
#9
#9
#9
#6
#20
#21
#21 #21
#20
#20
#20
#21
#26
#28
Note: Finished edge will
face front and the gears
will be on the bottom of
all storage shelves.

ASSEMBLY INSTRUCTIONS (CONT.)
7
#21
#20
#21
#21
Step 5: Attach the dart holder #12 using the pre-drilled holes on the door with screw #18.
Attach the doors #8 to the bottom cabinet with hinges #13 and screw #16 and screw #17.
Attach the legs #11 to the cabinet bottom with washer #15 and bolt #14. Note: see Step 7
if attaching to wall. Attach the door handles #22 to the doors. Attach the magnet steel plates
#27 to pre-drilled holes in top outer cor ners on the inside of the doors with screw #29.
Step 6: Screw thread bolts #21 into the bottom cabinet and attach the top cabinet to the bottom
cabinet with gears #20 as shown below..
#16
#11
#14
#15
#8
#12 #18
#8
#11
#16
#17
#13
#22
#27
#29

ASSEMBLY INSTRUCTIONS (CONT.)
8
#24
#24
#25
#24
Step 7: Attach the electronic dartboard #25, using the threaded holes on backboard, with bolts #24.
Optional (attach the cabinet to a wall):
If you plan to attach the cabinet to a wall, don't
attach the legs #11. Use the 16" on center pre-drilled
holes in the backboard to attach the top and bottom
cabinet to the wall with screw #19 as shown.
Please make sure to screw into wall studs or use
the appropriate wall anchors (not included).
WALL
#19
#19
#19
16"
#24
#24
#25

CONGRATULATIONS!
You have now assembled your Game Table.
Please note the Care and Use instructions below to
ensure years of trouble free use of your game table.
CARE AND USE
1. This product is intended for INDOOR use only.
2. Do NOT sit, climb or lean on the table.
3. Do NOT drag the table when moving it as this will damage the legs.


180-DAY LIMITED WARRANTY
This product is warranted to the original purchaser to be free from defects in material or workmanship
for a period of 180 days from the date of the original retail purchase.
This warranty does not cover defects or damage due to improper installation, alteration, accident or
any other event beyond the control of the manufacturer. Defects or damage resulting from misuse,
abuse or negligence will void this warranty. This warranty does not cover scratching or damage that
may result from normal usage.
This product is not intended for institutional or commercial use; the manufacturer does not assume
any liability for such use. Institutional or commercial use will void this warranty.
This warranty is nontransferable and is expressly limited to the repair or replacement of the defective
product. During the warranty period, the manufacturer shall repair or replace defective parts at no
cost tothe purchaser. Shipping charges and insurance are not covered and are the responsibility of
the purchaser. Labor charges and related expenses for removal, installation or replacement of the
product or components are not covered under this warranty.
The manufacturer reserves the right to make substitutions to warranty claims if parts are unavailable
or obsolete.
The manufacturer shall not be liable for loss of use of the product or other consequential or incidental
costs, expenses or damages incurred by the consumer of any other use. The user assumes all risk of
injury resulting from the use of this product.
This warranty is expressly in lieu of all other warranties, expressed or implied, including warranties of
. Neither the manufac-
turer nor any of its representatives assumes any other liability in connection with this product.
All warranty claims must be made through the retailer where the product was originally
purchased. A purchase receipt or other proof of date of purchase will be required to process
all warranty claims. The model number and part numbers found within the assembly
instructions will be required when submitting any parts requests or warranty claims.
For further warranty information or inquiries, please call 800-759-0977