HAUL MASTER 34313 User manual

EXCESSCARGOCARRIER
ASSEMBLYandOPERATINGINSTRUCTIONS
3491MissionOaksBlvd./Camarillo,CA93011
Copyright © 1997 by Harbor Freight Tools®. All rights reserved.
No portion of this manual or any artwork contained herein may be reproduced in any
shape or form without the express written consent of Harbor Freight Tools.
For technical questions and replacement parts, please call 1-800-444-3353.
®

SPECIFICATIONS
SAVE THIS MANUAL
You will need the manual for the safety warnings and cautions, assembly instructions, operating
procedures, maintenance procedures, trouble shooting, parts list, and diagram. Keep your
invoice with this manual. Write the invoice number on the inside of the front cover. Keep
both this manual and your invoice in a safe, dry place for future reference.
SAFETYWARNING & CAUTIONS
WARNING: When using electric tools, machines, or equipment, basic safety precautions should
always be followed to reduce the risk of fire, electric shock, and personal injury. READ ALL
INSTRUCTIONS BEFORE USING THIS TOOL!
1. KEEP WORK AREA CLEAN. Cluttered areas invite injuries.
2. OBSERVE WORK AREA CONDITIONS. Do not use machines or power tools in damp,
wet, or poorly lit locations. Don’t expose to rain. Keep work area well lit. Do not use electri-
cally powered tools in the presence of flammable gases or liquids.
3. KEEP CHILDREN AWAY. Children must never be allowed in the work area. Do not let them
handle machines, tools, or extension cords.
4. STORE IDLE EQUIPMENT. When not in use, tools must be locked up in a dry location to
inhibit rust. Always lock up tools and keep out of reach of children.
5. DO NOT FORCE THE TOOL. It will do the job better and more safely at the rate for which it
was intended. Do not use inappropriate attachments in an attempt to exceed the tool’s
capacities.
6. USE THE RIGHT TOOL FOR THE JOB. Do not attempt to force a small tool or attachment
to do the work of a larger industrial tool. Do not use a tool for a purpose for which it was not
intended.
7. DRESS PROPERLY. Do not wear loose clothing or jewelry as they can be caught in moving
parts. Protective, electrically non-conductive clothes and non-skid footwear are recom-
mended when working. Wear restrictive hair covering to contain long hair.
8. USE EYE AND EAR PROTECTION. Always wear ANSI approved chemical splash goggles
when working with chemicals. Always wear ANSI approved impact safety goggles at other
Platform Dimensions 20" x 60"
Carrying Capacity 500 lbs.
Hitch Size 2" Standard
Total Weight 52 lbs.
Page 2 -- SKU: 34313
®

9. DO NOT ABUSE THE POWER CORD. Do not yank it to disconnect it from the receptacle.
Do not carry tools by the cord.
10. DO NOT OVERREACH. Keep proper footing and balance at all times. Do not reach over or
across running machines.
11. MAINTAIN TOOLS WITH CARE. Keep tools sharp and clean for better and safer perfor-
mance. Follow instructions for lubricating and changing accessories. Inspect tool cords
periodically and, if damaged, have them repaired by an authorized technician. The handles
must be kept clean, dry, and free from oil and grease at all times.
12. DISCONNECT POWER. Unplug when not in use, before servicing, and when changing
accessories.
13. REMOVE ADJUSTING KEYS AND WRENCHES. Make it a habit to check that keys and
adjusting wrenches are removed from the tool or machine work surface before plugging it in.
14. AVOID UNINTENTIONAL STARTING. Be sure the switch is in the OFF position when not in
use and before plugging in. Do not carry any tool with your finger on the trigger, whether it is
plugged in or not.
15. OUTDOOR EXTENSIONS CORDS. When the equipment is operated outdoors, use only
extension cords intended for outside use. See chart under “Extension Cords” for the proper
AWG rating depending on the length of the cord(s) being used.
16. STAYALERT. Watch what you are doing; use common sense. Do not operate any tool when
you are tired.
17. CHECK DAMAGED PARTS. Before using any tool, any part that appears damaged should
be carefully checked to determine that it will operate properly and perform its intended
function. Check for alignment and binding of moving parts; any broken parts or mounting
fixtures; and any other condition that may affect proper operation.Any part that is damaged
should be properly repaired or replaced by a qualified technician. Do not use the tool if any
switch does not turn on and off properly.
18. GUARD AGAINST ELECTRIC SHOCK. Prevent body contact with grounded surfaces such
as pipes, radiators, ranges, and refrigerator enclosures.
19. REPLACEMENT PARTS AND ACCESSORIES. When servicing, use only identical replace-
ment parts. Use of any other parts will void the warranty. Only use accessories intended for
use with this tool.Approved accessories are available from Harbor Freight Tools.
20. DO NOT OPERATE TOOL IF UNDER THE INFLUENCE OF ALCOHOL OR DRUGS. Read
warning labels on prescriptions to determine if your judgment or reflexes are impaired while
taking drugs. If there is any doubt, do not operate the tool.
Page 3 -- SKU: 34313
times. Wear a full face shield if you are producing metal filings or wood chips. Wear an ANSI
approved dust mask or respirator when working around metal, wood, and chemical dusts
and mists.
REV 09/02
®

UNPACKING
If any parts are missing or broken, please call Harbor Freight Tools at the number on the cover of
this manual.
Ref Item Description Quantity
A Receiver Mounting Bar 1
N/A HardwareBag 1
B Detachable Side Rail 2
C1 Side Rail Brace 3
C2 Side Rail Brace 3
D Bed Frame 1
ASSEMBLY
Step 1: Place all the pieces for your Excess Cargo Carrier onto a clear work area.
Step 2: Make sure the set of three holes in the RECEIVER MOUNTING BAR (#A) are oriented
vertically. Turn the RECEIVER MOUNTING BAR to properly orient it.
Step 3: Insert the RECEIVER MOUNTING BAR (#A) under the mesh screen of the BED
FRAME (#D) and between the arched Bed Frame Supports as shown in Figure 1.
Bed Frame
(#D)
Receiver
Mounting Bar
(#A)
Figure 1 — Attatching the Mounting Receiver Bar
Page 4 -- SKU: 34313 REV 09/02
Caution: Be aware of the possible risk of fire and damage to property resulting from the
vehicle’s exhaust pipe pointing at the cargo put in this Cargo Carrier. Before installing the Cargo
Carrier, check to make sure that the exhaust pipe is not pointing in the direction of the cargo.
Flammable cargo can ignite from exposure to heat. Other cargo can be damaged from the heat.
Always be aware of this potential danger, and never use the Cargo Carrier if this risk exists.
REV 10/02

Step 4: Insert two HEX BOLTS (#E) through the top of the BED FRAME and down through the
RECEIVER MOUNTING BAR as shown in Figure 2.
Hex Bolts
(#E)
Nuts
(#F)
Figure 2 — Inserting Hex Bolts
Step 5: Attach a NUT (#F) to each of the HEX BOLTS and tighten.
Detachable Side Rails
The following Steps show how to assemble the DETACHABLE SIDE RAILS (#B). These side
rails should always be in place when using the Excess Cargo Carrier.
Page 5 -- SKU: 34313 REV 09/02
®

Step 1: Attach one DETACHABLE SIDE RAIL to the outside corners of the BED FRAME as
shown in Figure 3. Assemble with one BOLT (#G) and one NUT (#H) per corner.
Tighten the NUTS.
Figure 3 — Attaching Side Rails
Step 2: Place a SIDE RAIL BRACE (#C1) outside on the vertical folded edges of the DETACH-
ABLE SIDE RAIL and BED FRAME as shown in Figure 4.
Figure 4 — Attaching Center Side Rail Braces
Bolts
(#G)
Nuts
(#H)
Side Rail
Brace
(#C1)
Nut
(#H)
Nut
(#H)
Bolt
(#G)
Bolt
(#G)
Detachable
Side Rail
(#B)
Detachable
Side Rail
(#B)
Page 6 -- SKU: 34313

Step 3: Assemble with two BOLTS (#G) and two NUTS (#H) using the holes in the DETACH-
ABLE SIDE RAIL and BED FRAME. Tighten the NUTS.
Step 4: Attach a SIDE RAIL BRACE (#C2) to the inside vertical folded edges of the corner of
the Carrier Assembly as shown in Figure 5. Attach with two BOLTS and two NUTS.
Tighten the NUTS.
Bolts
(#G)
Bolts
(#G)
Nuts
(#H)
Side Rail
Brace
(#C2)
Side Rail
Brace
(#C2)
Figure 5 — Attaching Corner Side Rail Braces
Step 5: Repeat Step 4 for the other corner of the CarrierAssembly.
Step 6: Repeat Steps 1 through 5 to assemble the second DETACHABLE SIDE RAIL.
Your Excess Cargo Carrier is ready for use.
Page 7 -- SKU: 34313 REV 09/02
®

Your Excess Cargo Carrier can be loaded with up to 500 lbs. of cargo.
Caution: The load weight must be centered or evenly distributed across the Bed Frame (D).
Always use appropriate tie-down restraints to securely attach any cargo loaded onto the Excess
Cargo Carrier before moving your vehicle any distance. Do not leave loose items on the BED
FRAME while operating the vehicle.
DO NOT EXCEED THE MANUFACTURER’S RECOMMENDED PRODUCT WEIGHT
CAPACITY. Doing so can result in personal injury and/or damage to the product.
Caution: Be aware of dynamic loading! If the vehicle hits a bump, a slight play in the receiv-
ing hitch or a movement in the load could result in a momentary dynamic loading effect that
could dramatically increase the actual load weight. This momentary dynamic loading effect
could result in damage to the Excess Cargo Carrier, damage to the load and possible personal
injury.
Note: Any load over 350 Lbs. requires a Class 3 hitch on the vehicle.
(Class 2 Hitch = 350 Lbs. maximum tongue weight)
(Class 3 Hitch = 500 Lbs. maximum tongue weight)
PARTS LIST
Item# Description Qty Item# Description Qty
A Receiver Mounting Bar 1 E Hex Bolt M10 2
B Detachable Side Rail 2 F Nut M10 2
C1 Side Rail Brace 2 G Hex Bolt M6 16
C2 Side Rail Brace 4 H Nut M6 16
D Bed Frame 1
OPERATION
Step 1: Request a friend’s help to lift the Excess Cargo Carrier.
Step 2: Lift the Excess Cargo Carrier and place the RECEIVER MOUNTING BAR into the
Hitch Receiver mounted to your vehicle.
Step 3: Line up the horizontal hole in the RECEIVER MOUNTING BAR with the hole in your
Hitch. When the holes line up, place your locking mechanism through the holes to
secure the Excess Cargo Carrier.
Page 8 -- SKU: 34313 REV 09/02

ASSEMBLYDIAGRAM
DISCLAIMER
PLEASE READ THE FOLLOWING CAREFULLY
THE MANUFACTURER AND/OR DISTRIBUTOR HAS PROVIDED THE PARTS
DIAGRAM IN THIS MANUAL AS A REFERENCE TOOL ONLY. NEITHER THE
MANUFACTURER NOR DISTRIBUTOR MAKES ANY REPRESENTATION OR WAR-
RANTY OF ANY KIND TO THE BUYER THAT HE OR SHE IS QUALIFIED TO MAKE
ANY REPAIRS TO THE PRODUCT OR THAT HE OR SHE IS QUALIFIED TO RE-
PLACE ANY PARTS OF THE PRODUCT. IN FACT, THE MANUFACTURER AND/OR
DISTRIBUTOR EXPRESSLY STATES THE ALL REPAIRS AND PARTS REPLACE-
MENTS SHOULD BE UNDERTAKEN BY CERTIFIED AND LICENSED TECHNI-
CIANS AND NOT BY THE BUYER. THE BUYER ASSUMES ALL RISK AND LIABIL-
ITY ARISING OUT OF HIS OR HER REPAIRS TO THE ORIGINAL PRODUCT OR
REPLACEMENT PARTS THERETO, OR ARISING OUT OF HIS OR HER INSTALLA-
TION OF REPLACMENT PARTS THERETO.
Page 9 -- SKU: 34313
®