HAUL MASTER 93226 Assembly instructions

Page 2 For technical questions, please call 1-888-866-5797. Item 93226, 93227
Specifications
Product Application Marker / Clearance Lamps
Overall Dimensions: 4-1/8” L x 2-1/16” W x 1” H
Housing: 4-1/8” L x 2-1/16” W x 5/8” H
Lens: 4” L x 2” W x 11/16” H.
Mounting Holes: 1/4” diameter and 3” apart at centers
Construction: White ABS Poly and lens is red/amber acrylic.
Light Bulb: 12VDC (2 included)
Important Safety Information
Assembly Precautions
1. Assemble only according to these
instructions. Improper assembly
can create hazards.
2. Wear ANSI-approved safety goggles and
heavy-duty work gloves during assembly.
3. Keep assembly area clean and well lit.
4. Keep bystanders out of the
area during assembly.
5. Do not assemble when tired
or when under the influence of
alcohol, drugs or medication.
6. Replacement parts and accessories.
When servicing, use only identical
replacement parts. Use of any other
parts will void the warranty.
7. Always check hardware and assembled
parts after assembling. All connections
should be tight and hardware tightened.
8. Weight capacity and other product
capabilities apply to properly and
completely assembled product only.
Use Precautions
1. This product is not a toy. Do not allow
children to play with or near this item.
2. Use as intended only.
3. Inspect before every use; do not use
if parts are loose or damaged.
4. Use the right product for the job.
There are certain applications for
which the Lamp was designed.
5. Make certain to follow all local DMV
(Department of Motor Vehicles)
laws regarding vehicles and
vehicle lighting requirements.
6. Do not cut or rewire any
part of the Lamp.
7. Make certain the vehicle is turned
off before doing any maintenance.
8. The warnings, cautions, and instructions
discussed in this instruction manual
cannot cover all possible conditions
and situations that may occur. It must
be understood by the operator that
common sense and caution are factors
which cannot be built into this product,
but must be supplied by the operator.
9. Maintain product labels and nameplates.
These carry important safety information.
If unreadable or missing, contact
Harbor Freight Tools for a replacement.

Page 3For technical questions, please call 1-888-866-5797.Item 93226, 93227
Assembly Instructions
Read the ENTIRE IMPORTANT SAFETY INFORMATION section
at the beginning of this document including all text under subheadings therein
before set up or use of this product.
Before operating this product be sure that you
have all parts described in the Parts List and
Assembly Diagram located on page 4 of this
manual. If you do not have experience doing
this type of electrical work, the job should be
done by an automotive service technician.
1. Make certain that the vehicle’s engine
is OFF before doing any maintenance
or installation. Proceed with the
following steps for assembling the
2 Piece Marker/Clearance Lamp.
2. Use a pin connector or in-line splice
connector (neither included) to
connect the 2 Piece Marker/Clearance
Lamp to your vehicle. When using
an in-line splice connector, it is not
necessary to strip the wires.
3. Insert the wire from your vehicle into one
channel of the in-line splice connector.
Insert the wire extending from the Lamp
into the second channel of the in-line splice
connector. Fold down the tab on the in-line
splice connector to make the connection.
4. When mounting the lights to a trailer,
both the forward (amber) and rear
(red) marker lights are connected
to the trailer’s tail light wires.
5. When attaching the Lamp to the
vehicle or trailer, the ground screw
must make contact with a metal
surface to assure proper grounding.
6. Once the wires are properly connected,
test them before setting the Lamp in place.
7. To mount onto a trailer or vehicle, use
the mounting holes on the Lamp. The
mounting holes are spaced 3" from center
to center and are 1/4" diameter. Make
certain that the ground screw makes
proper contact with a metal surface.
Mounting hardware is not included.
Installing the Light Bulb
1. To remove the Lens insert a screwdriver
between the Lens and Housing.
Gently twist the screwdriver to pry
the Lens) off of the Housing.
2. Gently grasp the Light Bulb (12VDC)
(included) and slide it into the
socket. Twist until the Light Bulb
locks in place. See Figure A.
Socket
Light Bulb
Housing
Figure A
3. Verify that the Light Bulb is
securely in place. Snap the Lens
back onto the Housing.

Record Serial Number Here:
Note: If product has no serial number, record
month and year of purchase instead.
Note: Replacement parts are
not available for this item.
Limited 90 Day Warranty
Harbor Freight Tools Co. makes every effort to assure that its products meet high quality
and durability standards, and warrants to the original purchaser that this product is free from
defects in materials and workmanship for the period of 90 days from the date of purchase.
This warranty does not apply to damage due directly or indirectly, to misuse, abuse, negligence
or accidents, repairs or alterations outside our facilities, criminal activity, improper installation,
normal wear and tear, or to lack of maintenance. We shall in no event be liable for death,
injuries to persons or property, or for incidental, contingent, special or consequential damages
arising from the use of our product. Some states do not allow the exclusion or limitation of
incidental or consequential damages, so the above limitation of exclusion may not apply to you.
THIS WARRANTY IS EXPRESSLY IN LIEU OF ALL OTHER WARRANTIES, EXPRESS
OR IMPLIED, INCLUDING THE WARRANTIES OF MERCHANTABILITY AND FITNESS.
To take advantage of this warranty, the product or part must be returned to us
with transportation charges prepaid. Proof of purchase date and an explanation
of the complaint must accompany the merchandise. If our inspection verifies the
defect, we will either repair or replace the product at our election or we may elect
to refund the purchase price if we cannot readily and quickly provide you with a
replacement. We will return repaired products at our expense, but if we determine
there is no defect, or that the defect resulted from causes not within the scope
of our warranty, then you must bear the cost of returning the product.
This warranty gives you specific legal rights and you may also
have other rights which vary from state to state.
3491 Mission Oaks Blvd. • PO Box 6009 • Camarillo, CA 93011 • 1-888-866-5797