HAUL MASTER 61283 Assembly instructions

61283
Visit our website at: http://www.harborfreight.com
Email our technical support at: [email protected]
Owner’s Manual & Safety Instructions
Save This Manual Keep this manual for the safety warnings and precautions, assembly,
operating, inspection, maintenance and cleaning procedures. Write the product’s serial number in the
back of the manual near the assembly diagram (or month and year of purchase if product has no number).
Keep this manual and the receipt in a safe and dry place for future reference. 20k
When unpacking, make sure that the product is intact
and undamaged. If any parts are missing or broken,
please call 1-888-866-5797 as soon as possible.
Copyright© 2020 by Harbor Freight Tools®. All rights reserved.
No portion of this manual or any artwork contained herein may be reproduced in
any shape or form without the express written consent of Harbor Freight Tools.
Diagrams within this manual may not be drawn proportionally. Due to continuing
improvements, actual product may differ slightly from the product described herein.
To ols required for assembly and se rv ic e m ay n ot b e i nc lu de d .
Read this material before using this product.
Failure to do so can result in serious injury.
SAVE THIS MANUAL.

Page 2 For technical questions, please call 1-888-866-5797. Item 61283
Specifications
Maximum Weight Capacity 1000 lb. (per Dolly)
Wheels Four Swivel Casters
Maximum Tire Width 13-9/16"
Important Safety Information
Assembly Precautions
1. Assemble only according to these
instructions. Improper assembly
can create hazards.
2. Wear ANSI-approved safety goggles
and heavy-duty work gloves
during assembly.
3. Keep assembly area clean and well lit.
4. Keep bystanders out of the
area during assembly.
5. Do not assemble when tired
or when under the influence
of drugs or medication.
6. Weight capacity and other product
capabilities apply to properly and
completely assembled product only.
Use Precautions
1. Study, understand, and
follow all instructions before
operating this device.
2. Do not exceed rated capacity.
3. Use only on hard level surface.
4. Before moving a load, assure that
the load is centered and secured
with a load restraint device.
5. No alterations shall be
made to this product.
6. Wear ANSI-approved safety goggles
and heavy-duty work gloves
during use.
7. Keep clear of load′s path while
placing on and removing from
dollies, and while moving.
8. Do not use for aircraft purposes.
9. Inspect before every use; do not
use if parts loose or damaged.
10. Be aware of dynamic loading!
Sudden load movement may
briefly create excess load
causing product failure.
11. Use Vehicle Dollies to support
FRONT or REAR end of the vehicle.
Do not use Dollies to support one
side of vehicle. Use four Dollies
(two pairs) to support entire vehicle.
12. Read vehicle owner’s manual
and instruction manual for
Jack (not included) for proper
jacking positions before use.
13. Position Dollies so that rails
are parallel to the wheels.
14. Make sure sides of tires do not
press against Dolly edges.
15. If used for extended storage under
Vehicle tires, periodically lift Vehicle
and turn tires to preserve tire shape.

Page 3For technical questions, please call 1-888-866-5797.Item 61283
16. Move supported vehicle carefully
and slowly. Keep all people and body
parts out of path of moving vehicle.
17. Do not work on supported vehicle.
18. Keep lifting area free of spectators
and do not allow anyone into
vehicle while on Dollies.
19. Use wheel chocks at opposite
end of vehicle when lifting.
20. This product is not a toy. Do not allow
children to play with or near this item.
21. Maintain product labels and
nameplates. These carry
important safety information.
If unreadable or missing, contact
Harbor Freight Tools for a replacement.
Assembly and Use Instructions
1. Insert Casters through holes in Frame.
Fasten together using Spring Washers
and Acorn Nuts. See Diagram, below.
2. Repeat for other Dolly.
3. Once Dollies are assembled, roll Dollies
along surface to verify all connections
are secure and Dollies roll freely.
4. Chock wheels (or chock dollies if
another set of dollies is already in use)
on opposite end of vehicle.
Use appropriate jacks to safely lift front
or rear end of vehicle. Place Dollies
in position under raised wheels and
lower vehicle slowly onto them.
5. If raising front and rear of vehicle, use
jack to raise other end, remove wheel
blocks, and set up four Dollies (sold
in sets of two). Once vehicle is resting
on all Dollies, carefully guide vehicle.
Parts List and Diagram
Part Description Qty
1 Frame 2
2 Swivel Caster 8
3 Spring Washer Ø12 8
4 Acorn Nut M12 8
Record Serial Number Here:
Note: If product has no serial number,
record month and year of purchase instead.
Note: Some parts are listed and shown
for illustration purposes only, and are
not available individually as replacement
parts. Specify UPC 193175020925
when ordering parts.

PLEASE READ THE FOLLOWING CAREFULLY
THE MANUFACTURER AND/OR DISTRIBUTOR HAS PROVIDED THE PARTS LIST AND ASSEMBLY
DIAGRAM IN THIS DOCUMENT AS A REFERENCE TOOL ONLY. NEITHER THE MANUFACTURER
OR DISTRIBUTOR MAKES ANY REPRESENTATION OR WARRANTY OF ANY KIND TO THE
BUYER THAT HE OR SHE IS QUALIFIED TO MAKE ANY REPAIRS TO THE PRODUCT, OR
THAT HE OR SHE IS QUALIFIED TO REPLACE ANY PARTS OF THE PRODUCT. IN FACT, THE
MANUFACTURER AND/OR DISTRIBUTOR EXPRESSLY STATES THAT ALL REPAIRS AND PARTS
REPLACEMENTS SHOULD BE UNDERTAKEN BY CERTIFIED AND LICENSED TECHNICIANS,
AND NOT BY THE BUYER. THE BUYER ASSUMES ALL RISK AND LIABILITY ARISING OUT OF
HIS OR HER REPAIRS TO THE ORIGINAL PRODUCT OR REPLACEMENT PARTS THERETO,
OR ARISING OUT OF HIS OR HER INSTALLATION OF REPLACEMENT PARTS THERETO.
Limited 90 Day Warranty
Harbor Freight Tools Co. makes every effort to assure that its products meet high quality
and durability standards, and warrants to the original purchaser that this product is free from
defects in materials and workmanship for the period of 90 days from the date of purchase.
This warranty does not apply to damage due directly or indirectly, to misuse, abuse, negligence
or accidents, repairs or alterations outside our facilities, criminal activity, improper installation,
normal wear and tear, or to lack of maintenance. We shall in no event be liable for death,
injuries to persons or property, or for incidental, contingent, special or consequential damages
arising from the use of our product. Some states do not allow the exclusion or limitation of
incidental or consequential damages, so the above limitation of exclusion may not apply to you.
THIS WARRANTY IS EXPRESSLY IN LIEU OF ALL OTHER WARRANTIES, EXPRESS OR
IMPLIED, INCLUDING THE WARRANTIES OF MERCHANTABILITY AND FITNESS.
To take advantage of this warranty, the product or part must be returned to us with transportation
charges prepaid. Proof of purchase date and an explanation of the complaint must accompany
the merchandise. If our inspection verifies the defect, we will either repair or replace
the product at our election or we may elect to refund the purchase price if we cannot readily
and quickly provide you with a replacement. We will return repaired products at our expense,
but if we determine there is no defect, or that the defect resulted from causes not within
the scope of our warranty, then you must bear the cost of returning the product.
This warranty gives you specific legal rights and you may also
have other rights which vary from state to state.
26541 Agoura Road • Calabasas, CA 91302 • 1-888-866-5797