HAUL MASTER 92709 Quick reference guide

ASSEMBLY & OPERATING INSTRUCTIONS
92709
3491 Mission Oaks Blvd., Camarillo, CA 93011
Visit our Web Site at www.harborfreight.com
Copyright©2005 by Harbor Freight Tools®. All rights reserved. No portion of this manual or
any artwork contained herein may be reproduced in any shape or form without the
express written consent of Harbor Freight Tools.
For technical questions and replacement parts please call 1-800-444-3353.
®
HAND TRUCK
ALUMINUM FOLDING

SKU 92709 For technical questions please call 1-800-444-3353. Page 2
THANKYOU for choosing a HARBOR FREIGHTTOOLS product. For future reference, please
complete the owner’s record below:
Model______________ Serial No._____________ Purchase Date_______________
SAVE THE RECEIPT, WARRANTY AND THESE INSTRUCTIONS. It is important that you read the
entire manual to become familiar with the unit BEFORE you begin assembly.
Technical Specifications
Material: Aluminum Alloy
Folding Dimensions: 2.37” L x 19.3”W x 30.1” H
Toe Dimension: 19-1/8” L x 10-1/2” D
Wheels: 7” Diameter x 1-3/8 W
Maximum Weight Capacity: 200 Lbs.
Safety Warnings and Precautions
WARNING:When using product, basic safety precautions should always be followed to
reduce the risk of personal injury and damage to equipment.
Read all instructions before using this product!
1. Keep work area clean. Cluttered areas invite injuries.
2. Observe work area conditions. Keep work area well lighted.
3. Store idle equipment. When not in use, the Hand Truck must be stored in a dry location to
inhibit rust. Always lock up products and keep out of reach of children.
4. Use the right product for the job. There are certain applications for which the Hand Truck
was designed.Do not modify the Folding Hand Truck and do not use the Folding Hand Truck for
a purpose for which it was not intended.
5. Check for damaged parts. Before using any product, any part that appears damaged should
be carefully checked to determine that it will operate properly and perform its intended function.
Check for any broken or damaged parts and any other conditions that may affect its operation.
Replace or repair damaged or worn parts immediately.
6. Replacement parts and accessories. When servicing, use only identical replacement parts.
Use of any other parts will void the warranty.
7. Do not operate product if under the influence of alcohol or drugs. Read warning labels on
prescriptions to determine if your judgment or reflexes are impaired while taking drugs. If there
is any doubt, do not operate the product.
8. Use eye protection. Always wear ANSI approved impact safety goggles.
9. Do not exceed the product’s maximum load capacity of 200 Lbs.

SKU 92709 For technical questions please call 1-800-444-3353. Page 3
10. Only use on a flat surface capable of supporting the HandTruck and its maximum
capacity load of 200 Lbs . It is easy to lose control of the HandTruck if attempting to pull a
load on a sloping or uneven surface. Always use an assistant when handling heavy loads.
11. Do not allow children to play on, stand upon or climb into the HandTruck. The Hand
Truck is not for carrying people or animals.
12. Always check hardware and assembled parts after assembling. All connections should be
tightand hardware tightened.
13. Always distribute objects in the HandTruck evenly. Uneven weight distribution could cause
tipping. Harbor Freight Tools is not responsible for damage to persons or cargo. Do not lean or
climb on the side panels.
14. Be aware of dymanic loading! Suddenly dropping or bouncing a load on the Hand Truck may
create, for a brief instant, an excess load, which may result in damage to the product and/or
personalinjury.
15. Be careful with the Stretch Cord. Cords can be dangerous; if they come undone they will act
as a projectile and will cause serious damage. Do not allow children to play with or use the
Stretch Cord.
Warning: The warnings, cautions, and instructions discussed in this instruction manual cannot
cover all possible conditions and situations that may occur. It must be understood by
the operator that common sense and caution are factors which cannot be built into
this product, but must be supplied by the operator.
Unpacking
When unpacking your Aluminum Folding Hand Truck, check to make sure the following parts
are included. If any parts are missing or broken, please call HARBOR FREIGHT TOOLS
at1-800-444-3353.
Assembly
Your Hand Truck comes completely assembled. It is important that you read the entire manual to
become familiar with the product BEFORE you use the Hand Truck. Before operating the Hand
Truck be sure that you have all parts described in the Parts List and Assembly Diagram located on
the last pages of this manual.
To Open and Close
1. To release the Handle (2), press down on the Button (5) located on the bar beneath the
Handle (2)-see Assy Diagram and Figure 1. At the same time, pull up on the Handle (2) and
push down on the Plate (23) with your shoe-see Figure 1.
2. Set the Handle (2) to the height you desire.
3. To close the Hand Truck, reverse the above instructions. Press down on the Button (5),
push down on the Handle (2) and pull the Plate (23) up into its closed position-see Figure 2.

SKU 92709 For technical questions please call 1-800-444-3353. Page 4
Button(5)
Plate (23)
Figure 1-Opening Figure 2-Hand Truck Folded Up
Operation
1. Open the Hand Truck as in previous steps. Place the load on the Plate (23). Do not exceed
the maximum weight limit of 200 Lbs.
2. Secure load with Stretch Cord (29). If the load can not be securely secured using the
Stretch Cord, you may need to use a rope (not included) or some other method to safely
secure the load.
3. Using two hands, move the Hand Truck with its load. Make certain the load is evenly
distributed and is centered on the HandTruck.
Caution: Always use two hands when moving the HandTruck. This provides support in
case one hand slips while moving a load.
Parts List
Part # Description Quantity Part # Description Quantity
1 Foam Grip 1 16 Plug 2
2 Handle 1 17 Down Stator 2
3 Tuble Clip 1 18 Shrink Tack 4
4 Rivet 4 19 Wheel 2
5 Button 1 21 Long Screw 2
6 Frame 1 22 Lock Nut 2
7 Sheath 2 23 Plate 1
8 Rivet 2 24 Short Screw M4 x 16 4
9 StrentheningTube 1 25 M4 Lock Nut 4
10 Tri-Tube 2 26 Up Stator 2
11 Rivet 2 27 Gear 2
12 Set 2 28 Round Screw 2
13 Wheel Bracket 2 29 Stretch Cord 1
14 Middle Screw 2
15 Lock Nut M6 2

SKU 92709 For technical questions please call 1-800-444-3353. Page 5
Note: Some parts are listed and shown for illustration purposes only and are not available
individually as replacement parts.
PLEASE READ THE FOLLOWING CAREFULLY
THE MANUFACTURER AND/OR DISTRIBUTOR HAS PROVIDED THE PARTS DIAGRAM IN THIS MANUAL AS A REFERENCE
TOOL ONLY. NEITHER THE MANUFACTURER NOR DISTRIBUTOR MAKES ANY REPRESENTATION OR WARRANTY OF ANY
KIND TO THE BUYER THAT HE OR SHE IS QUALIFIED TO MAKE ANY REPAIRS TO THE PRODUCT OR THAT HE OR SHE IS
QUALIFIED TO REPLACE ANY PARTS OF THE PRODUCT. IN FACT,THE MANUFACTURER AND/OR DISTRIBUTOR EXPRESSLY
STATES THAT ALL REPAIRS AND PARTS REPLACEMENTS SHOULD BE UNDERTAKEN BY CERTIFIED AND LICENSED
TECHNICIANS AND NOT BY THE BUYER. THE BUYER ASSUMES ALL RISK AND LIABILITY ARISING OUT OF HIS OR HER
REPAIRSTOTHE ORIGINAL PRODUCT OR REPLACEMENT PARTSTHERETO, OR ARISING OUT OF HIS OR HER INSTALLATION
OF REPLACEMENT PARTS THERETO.
Parts/Assembly Diagram
#29-Stretch Cord not shown