Hawking Hi-Gain HAO14MD User manual

HW2R1 rev 1 I QIG v.20101118
Technical Support | Toll free US & Canada: 1.888.202.3344 | Email: techsuppor[email protected]
HAO14MD V1.QIG 20130515
QUICK INSTALLATION GUIDE
Part No. HAO14MD Hi-GainTM Outdoor 14dBi MiMo Directional Antenna Kit
www.hawkingtech.com
Technical Support: 1.888.202.3344
© 2013 Hawking Technologies, Inc. All rights reserved.
Start Here 
• Wireless Networking Device with
Removable Antennas
• Outdoor Antenna Cable
(Hawking Model No. HAC30N,
HAC20N, HAC10N, or
equivalent)
• Copper Grounding Wire
System Requirements
(not included)
Connecting the Antenna to your Wireless Device
NOTE: If your device
has only one removable
antenna port, you can
plug into the port of
your choice. If your
device has two ports,
use both antenna ports.
• HAO14MD Antenna
• N-Type to SMA Adapter (2)
• Pole Bracket Brace (2)
• Mounting Accessories:
U-Bracket (2), M6 Hex Nut (8)
M6 Bolt (4), M4 Wall Anchor (4)
M4 Screw (4), L-Bracket (2)
Package Includes
A. Attach a low-loss
outoor cable (not
included) to the
back of the Antenna
B. Connect your
Antenna Adapter
Cable to the end of
your low-loss cable
C. Remove the
antenna from your
wireless device and
affix the small gold
end to the antenna
port connector
Finding Signal
Once you have connected your Hi-GainTM Outdoor 14dBi MiMo Directional Antenna,
be sure to note the signal pattern of the antenna. While you will experience superior range
and quality with your HAO14MD, you must be in range of the antenna’s signal. As
indicated by the diagram at the right, the directional antenna does not give off signal
directly below or directly behind the product. You will receive optimal wireless signal by
placing your wi-fi enabled device within the designated area. Adjust the antenna as
needed. (NOTE: Your wireless coverage may vary depending on the receiving power of
your wireless adapter. This antenna only boosts the transmitting power of your device, not
the receiving power.)
Wireless Hot Spot
Use the HAO14MD to expand the wireless range of your router, bridge,
access point, or extender with 802.11 b/g/n compatible removable antennas.

Technical Support | Toll free US & Canada: 1.888.202.3344 | Email: techsuppor[email protected]
www.hawkingtech.com
Technical Support: 1.888.202.3344
© 2013 Hawking Technologies, Inc. All rights reserved.
Mounting Options
WALL MOUNT INSTALLATION
POLE MOUNT INSTALLATION
SPECIFICATIONS
Once you have determined the appropriate location for your antenna (Step 2), choose how you would like to mount it. The antenna kit
includes both a pole mounting option and a wall mounting option. Please being both options by attaching an “L-Bracket” to the back of
the antennas with four “M6 Nuts” as detailed in the image to the right.
A. Examine the aerial view of the
antenna a pole to the left. Using
the two included “U-Bracket”
included in the antenna kit,
thread them around the pole,
through the two “Pole Bracket
Brace” and the antenna’s
“L-Bracket”. Secure with four
“M-6 Nuts”.
B. Take note of the extra holes in
the “L-Bracket” and proceed to
Part C.
A. Examine the aerial view of the wall
to the left. Using a Screw Driver or
Drill, mount the “L-Bracket” not
attached to your antenna to your
wall with the four included “M-4
Wall Anchor” and “M-4 Screw”.
B. Next attach the “L-Bracket” on
your antenna to the “L-Bracket”
on the wall with the four “M-6
Bolt” and “M-6 Screw”.
C. Adjust the angle of your direc-
tional antenna according to your
network environment. Simply insert
the “U-Brackets” into the different
holes on the “L-Bracket” until you
have reached the desired mounting
angle. Tighten the “M-6 Nuts” with
a wrench to ensure a lasting hold.
C. Adjust the angle of your direc-
tional antenna according to your
network environment. Simply
thread the “M-6 Bolt” through a
different set of holes and secure
with an “M-6 Nut” until you have
reached the desired mounting
angle. Tighten with a wrench to
ensure a lasting hold.
aerial view
aerial view
side view
aerial view
Connector Brass
Pole Diameter 0.9 to 1.8inches
Operating Temp -40°F to 149°F
40° @H-plane
HPBW (3dB Beam Width) 25° @E-plane
Radiation Pattern Directional
Front/Back Ratio 15dBi
Dual Linear
Polarization Vertical / Horizontal
Gain 14dBi
V.S.W.R. < 2.0
Frequency Range 2.4GHz -2.435GHz
Impedance 50ohm
Insulator Material Teflon or Delrin
Contact Material Metal
Body Material Plastic
Weight 3 Lbs
Dimensions 14.6x9.1 x2.1 inches
Rated Wind Velocity 50m/s@ mount height 40m
side view
side view