Hawking HWUR54G User manual

1

2

3

1) POWER ON: After you have correctly connected your Range Extender to an
available Ethernet port on your Network, please power on the Extender and a PC that
is also on the netweork..
2) INSERT THE SETUP CD: Find the Setup-CD in your package and insert it into
your CD-Rom drive of the PC you wish to configure the Extender from.. Wait for
the Auto-Load Page to load. If the page does not load, please click on the “My
Computer” icon of you PC and find your CD-Rom Drive. Right-Click on the
CD-Rom drive icon and choose “Explore.” Find the file titled “autorun” and
execute it.
Click on the “Setup Wizard” tab to begin configuration of your Router.
4

3) SCAN FOR DEVICE: Once the Setup Wizard has loaded you will need to select
your device from a list of HWUR54G devices in your network. If nothing appears in
the box, double check all your connections and click on “Refresh.” Once the
Wizard has detected your device click “Next” to move on to the next step.
Note: If you wish to skip the Setup Wizard (Not Recommended) and go directly to the
Web-Configuration utility use the following default IP Address:192.168.1.235
User Name: admin Passworld: 1234
Please refer to the Users Manual for more
details.
5

4) SET IP ADDRESS: To successfully communicate to the HWUR54G, an IP
Address must be assigned to the unit. If you are on a network with a router that
distributes IP Address automatically (DHCP) you have the option to automatically
configure the IP Address. However the Extender must be connected to your network
and not directly to the PC for this to work.
You may also manually assign your IP Address (Recommended).
Note: The IP Address of the device must be in the same context/subnet of the PC it is
connected to in order to complete the setup of the device. The listed IP Address in
the Setup Wizard is the recommended IP based on the IP Address on your PC. You
may change the last number of the IP Address but it is highly recommended that you
DO NOT adjust the other numbers.
When you have selected your IP Address click “Next” to continue the setup.
6

5) STATUS: This screen displays the results of your settings. Please save this
information somewhere secure for future use. You will need to enter the IP address
in your web-browser for future configurations.
Click NEXT to continue.
7

Before you use the Web Based Configuration Panel you must enter the
default login information.
User Name: admin
Password: 1234
You can change the login information in the
ADMIN menu of the Configuration Panel.
8

Range Extender Setup Screen
Please view the setup diagram in this section to get a general idea of how
your wireless network setup should look like with the Hawking Range
Extender. (This section will go over the basics of what is needed to get
started. For more information on advanced settings please view the
Users Manual)
1) SSID of Original AP
The Original Wireless Access Point will be the source of the Wireless
network that you wish to extend.
Please input the SSID (Wireless Identification Name) of the “Original
Access Point” into the field that states SSID of Original AP.
(Note: If you do not know your Original AP’s SSID please contact your
wireless network administrator or contact Hawking technical support)
2) Channel Selection
The Range Extender must be set to the same channel that your original
access point is set on. So if the Channel number of your Original AP is
5 then the Range Extender must also be set to 5.
3) SSID of Extender
The SSID of the Extender is an identification name assigned to the Range
Extender so that wireless computers can access and connect to the
Extender. (It is recommended NOT to use the same ID as the Original
AP)
4) OPTIONAL – Security
If your wireless network uses WEP (Wireless Security) you will have to
input the correct security key associated to the original access point to
function correctly. If your wireless network does not use security
please skip this step.
Click APPLY when complete, allow 15 seconds for the Range Extender to
reboot. Disconnect the power and Ethernet cable and follow the next
step.
9

1) After you have completely configured your Range Extender you can
disconnect the Ethernet cable that connects the Extender to your network or
PC for configuration.
2) Take the Range Extender and Power Adapter and place the Extender in a
location half way between your original Access Point and the area that you are
below for more details:
3)Once y
extending your wireless coverage to. See the image
ou have
cated a good location,
plug the power adapter
wer
ht
ly.
4)Tit wirelessly with a wireless
nabled computer. Give the computer 15 seconds to obtain information from
pen
lo
into an available po
outlet and view the
LEDs on the Range
Extender. If the
Range Extender is
working the WLAN lig
should be blinking
repeatedly and the
PWR LED should
remain on constant
est the Range Extender by connecting to
e
the Range Extender after associating to the Range Extender’s SSID. O
your web browser and enter www.hawkingtech.com into the web address bar.
If the page loads your Wireless Range Extender is working correctly. If not
please check the troubleshooting section or reconfigure your Wireless Range
Extender.
10

1) I Can’t Pull up the Web Menu Screen?
In order to pull up the Web Based Configuration Menu your computer must be in
the same IP subnet as your Range Extender. For example, if your PC’s IP
configuration is the following:
IP: 192.168.0.5 Subnet 255.255.255.0 Gateway: 192.168.0.1
Then your Range Extender LAN IP address must be:
IP: 192.168.0.? (any # except 1 and 5) Subnet 255.255.255.0
Gateway: 192.168.0.1
Once these values match you should be able to pull up the Web Menu.
2) I Can’t Connect to the Wireless Repeater or the Internet
Make sure that all your settings are correct on the Range Extender.
Remember that the Original SSID must match the SSID of your original network.
The channel number of the extender must also match that of your original
network. For example, if your original network had the following settings:
SSID: HawkingAP
Channel: 6
LAN IP: 192.168.1.2
SUBNET: 255.255.255.0
- Then the settings of your Range Extender must be:
Original SSID: HawkingAP
Channel: 6
SSID of Range Extender: (any SSID other than HawkingAP)
LAN IP: 192.168.1.x (any number other than 2)
SUBNET: 255.255.255.0
GATEWAY: 192.168.1.2
After you have matched the settings check if you can connect to the internet through
the Wireless Range Extender. If you still cannot access the internet please contact
our technical support department using the number below.
11

Ethernet: A networking standard using cables (Category 5) to create a network.
Network Adapter: Also known as a NIC (Network Interface Card). Used to provide PC’s or laptops with an Ethernet port or
wireless access to the network.
Broadband Modem: A device that allows broadband connection to the internet. Broadband connections include speeds faster
than 56k (dial up modem speed). The two most common types of Broadband connections are DSL and Cable. Cable modem
relies on the bandwidth of cable television lines while DSL modems rely on the telephone lines operating at DSL speeds.
Router: A device used to share internet access from one user to multiple users. By taking one IP address (Addresses used by
ISP’s to assign broadband services to your computer) the Router distributes the services of your broadband access among
multiple users and IP’s.
Wireless IEEE 802.11 – Wireless Network Specifications
•802.11 -- applies to wireless LANs (Networks) and provides 1 or 2 Mbps transmission in the 2.4 GHz band using
either frequency hopping spread spectrum (FHSS) or direct sequence spread spectrum (DSSS).
•802.11b (also referred to as 802.11 High Rate or Wi-Fi) -- an extension to 802.11 that applies to wireless LANs and
provides 11 Mbps transmission (with a fallback to 5.5, 2 and 1 Mbps) in the 2.4 GHz band. 802.11b uses only DSSS.
802.11b was a 1999 ratification to the original 802.11 standard, allowing wireless functionality comparable to
Ethernet.
•802.11g -- applies to wireless LANs and provides 54 Mbps in the 2.4 GHz band. Backwards compatible with IEEE
802.11b products.
ESSID: A unique name identification for your wireless network. All wireless devices must have the same ID or else they will
not work together.
Channel: A Channel that all Wireless devices communicate on. All Wireless devices on the network must be set on the same
channel to work.
WEP/WPA: Wireless networking security protocols and standards, used to keep hackers from entering your wireless network.
12

13