Hawking Hi-Gain HAWNR3 User manual

QUICK INSTALLATION GUIDE
Part No. HAWNR3 Hi-Gain™ Wireless 300N Router with Range Amplifier
HAWNR3 - V1.QIG 2012.03.28
HW2R1 rev 1 I QIG v.20101118
Technical Support | Toll free US & Canada: 1.888.202.3344 | Email: techsuppor[email protected] www.hawkingtech.com
Start Here TV
oConfiguring the HAWNR3 Router using Wireless Connection
(For Wired Connection, please do Step 1d , then go straight to Step 3).
nHardware Setup
a.) Attached the two 3dBi
Antennas the the Router.
b.) Connect the A/C power
adapter to an electrical
source, and then connect
it to the ‘Power’ socket of
the router.
c.) Connect your Broadband Modem to
the Router’s “MODEM” port with an
Ethernet cable. Reset your modem by
unplugging it and plugging it back in.
d) (OPTIONAL: Only do this step if you
are going to configure the HAWNR3
using a wired connection)
Using an ethernet cable, connect your
computer to any one of the 4 Wired
LAN Ports located on the back of the
router. Proceed to step 3.
Package Contents
[:LUHOHVV15RXWHU
[9$3RZHU$GDSWHU
[G%L2PQL'LUHFWLRQDO$QWHQQDV
[6HWXS&'520
[4XLFN,QVWDOODWLRQ*XLGH
[(WKHUQHW&DEOH
Requirements
:LUHGRU:LUHOHVV,QWHUQHW&RQQHFWLRQ
$1HWZRUN(QDEOHG'HYLFH&RPSXWHU
6PDUW3KRQHRU7DEOHW
3RZHU2XWOHW
(optional)
Port 1-4
WAN
Internet Connection
LED is on, when there is an established connection with a cable/DSL modem
LED DESCRIPTION
Wired Connection (Port 1-4)
LED is on when a device is plugged in and connected to an associated port. Blinking when
transmitting/receiving data
Power
LED is on, when the power adapter is connected and plugged into an outlet
Wireless Connection
LED is on when Wireless Connection is established. Blinking when
transmitting/receiving wireless data
BACK PANEL DESCRIPTION
Wireless Radio On/Off Switch
Turns off the wireless functions
Power
12V1A Power Adapter Plug
Antennas
Two 3dBi Omni-Directional Antennas (Upgradable)
Antenna Connectors (RP-SMA)
Wired (4 LAN Ports)
LAN port connects your computer and other wired
network devices to your network
Reset Switch / WPS (WiFi Protected Setup)
Resets your router to its default settings / initiates WPS Setup
Modem Port
Connects to your Broadband Modem’s Ethernet port
Power Adapter
Broadband
Modem
Wired Laptop/
Desktop
For Windows Computer
1.) To connect to your HAWNR3 using a
Windows PC, click the ‘Network and
Sharing Center’ icon in your system tray.
2.) Find the HAWNR3, default ID: Hawking_300N,
(refer to the image on the right). Double click
on it to connect to the network. Proceed to
step 2C.
For Mac Computer
1.) Click the wireless network icon in
the upper right hand corner of the
Finder.
2.) From the drop-down menu select
your wireless network (default ID:
Hawking_300N). Proceed to step
2C.
Simply go to your Device’s
Wireless Settings (a).
Select “wireless & networks”
(b). Be sure to turn your Wi-Fi
on (c) and then join the
Hawking_300N network (d). For
more instructions on how to
connect to a wireless network,
please refer to your Device’s
User Manual.
For iPad® or iPhone®
Hawking_HD45R_...
(b)
2.) Make sure your Wi-Fi is connected
to the Router’s network (b).
1.) Go to Settings > Wi-Fi networks and
select Hawking_300N (a).
For Android® Mobile Device
(a)
(b)
(c)
Hawking_HD45R_...
(a)
Hawking_300N
Hawking_300N
(d)
Hawking_HD45R_2.4GHz
Hawking_300N

Broadband Type: L2TP
If you are using L2TP (Layer
Two Tunneling Protocol) , please
input your settings provided by
your Internet Service Provider
into the fields. Click Continue.
Broadband Type: PPTP
If you are using PPTP (Point to
Point Tunneling Protocol) , please
input your settings provided by
your Internet Service Provider into
the fields. Click Continue.
Broadband Type: PPPoE
If you are using PPPoE (Point-to-Point Protocol over
Ethernet), please enter your username/password. The
other fields are optional unless specified by your Internet
Service Provider. Please check with your Internet Service
Provider if you are not sure. Click Continue.
Broadband Type: Dynamic IP
Most common setup. If you have have a Dynamic
IP, put in your host name (optional) and your Mac
address (optional). Click Continue.
qPlease Enter your Broadband information.
Broadband Type: Static IP
If you have have a static IP, please input your IP
Address, Subnet Mask and Default Gateway and
DNS Address. These are provided by your Internet
Service Provider. Click Continue.
A.) Please enter a wireless name for your network.
By default, the HAWNR3’s wireless name is
Hawking_300N
C.) Congratulations. Please click “Finish” to
complete the setup process. If you wish to make
changes, click “Back”. After you click Finish, the
HAWNR3 will reset and enable your settings.
To connect your Wi-Fi enabled devices, simply go to
your Wi-Fi settings and select the newly configured
network.
To connect your WiFi enabled devices to
network, simply go to your WiFi settings and
select the newly configured network.
rSetup your wireless features
B.) Please enter a security key (optional). A wireless
security key is recommended to secure against
unwanted users. Type in an eight or more character
key or leave it blank, then click “Continue” Note: After
configuration, you will be prompted by your computer
to enter this key when you try to reconnect.
Note: If you decide to have a Wireless Security key, you will be
prompted to enter your password when you reconnect to the
HAWNR3.
© 2012 Hawking Technologies, Inc. All rights reserved. All trademarks herein are the property of
their respective owners. Apple, Mac, iPhone and iPad are registered trademarks of Apple Computer,
Inc. No affiliation implied or expressed.
Technical Support | Toll free US & Canada: 1.888.202.3344 | Email: techsuppor[email protected]
HAWNR3 - V1.QIG 2012.03.28
pLogin and Continue
A.) Open your web browser. In the address field,
type “192.168.1.254”, press enter to
connect to the Setup Page
A Username/password prompt will appear.
Default Username: admin
Password: 1234
B.) After loging in, the Quick Setup Tab will
automatically be selected. Please choose
your time zone. Click Next.
C.) Choose your broadband type and click Next.
[The most common type is Cable Modem (Dynamic
IP). If you are unsure of your broadband type, please
contact your internet service provider.]